Influence of stationary phase and eluent properties on chromatographic separation of carbohydrates

In this thesis, the sorption and elastic properties of the cation-exchange resins were studied to explain the liquid chromatographic separation of carbohydrates. Na+, Ca2+ and La3+ form strong poly(styrene-co-divinylbenzene) (SCE) as well as Na+ and Ca2+ form weak acrylic (WCE) cation-exchange resins at different cross-link densities were treated within this work. The focus was on the effects of water-alcohol mixtures, mostly aqueous ethanol, and that of the carbohydrates. The carbohydrates examined were rhamnose, xylose, glucose, fructose, arabinose, sucrose, xylitol and sorbitol. In addition to linear chromatographic conditions, non-linear conditions more typical for industrial applications were studied. Both experimental and modeling aspectswere covered. The aqueous alcohol sorption on the cation-exchangers were experimentally determined and theoretically calculated. The sorption model includes elastic parameters, which were obtained from sorption data combined with elasticity measurements. As hydrophilic materials cation-exchangers are water selective and shrink when an organic solvent is added. At a certain deswelling degree the elastic resins go through glass transition and become as glass-like material. Theincreasing cross-link level and the valence of the counterion decrease the sorption of solvent components in the water-rich solutions. The cross-linkage or thecounterions have less effect on the water selectivity than the resin type or the used alcohol. The amount of water sorbed is higher in the WCE resin and, moreover, the WCE resin is more water selective than the corresponding SCE resin. Theincreased aliphatic part of lower alcohols tend to increase the water selectivity, i.e. the resins are more water selective in 2-propanol than in ethanol solutions. Both the sorption behavior of carbohydrates and the sorption differences between carbohydrates are considerably affected by the eluent composition and theresin characteristics. The carbohydrate sorption was experimentally examined and modeled. In all cases, sorption and moreover the separation of carbohydrates are dominated by three phenomena: partition, ligand exchange and size exclusion. The sorption of hydrophilic carbohydrates increases when alcohol is added into the eluent or when carbohydrate is able to form coordination complexes with the counterions, especially with multivalent counterions. Decreasing polarity of the eluent enhances the complex stability. Size exclusion effect is more prominent when the resin becomes tighter or carbohydrate size increases. On the other hand,the elution volumes between different sized carbohydrates decreases with the decreasing polarity of the eluent. The chromatographic separation of carbohydrateswas modeled, using rhamnose and xylose as target molecules. The thermodynamic sorption model was successfully implemented in the rate-based column model. The experimental chromatographic data were fitted by using only one adjustable parameter. In addition to the fitted data also simulated data were generated and utilized in explaining the effect of the eluent composition and of the resin characteristics on the carbohydrate separation.

Critical flux and fouling in ultrafiltration of proteins

In this thesis different parameters influencing critical flux in protein ultrafiltration and membrane foul-ing were studied. Short reviews of proteins, cross-flow ultrafiltration, flux decline and criticalflux and the basic theory of Partial Least Square analysis (PLS) are given at the beginning. The experiments were mainly performed using dilute solutions of globular proteins, commercial polymeric membranes and laboratory scale apparatuses. Fouling was studied by flux, streaming potential and FTIR-ATR measurements. Critical flux was evaluated by different kinds of stepwise procedures and by both con-stant pressure and constant flux methods. The critical flux was affected by transmembrane pressure, flow velocity, protein concentration, mem-brane hydrophobicity and protein and membrane charges. Generally, the lowest critical fluxes were obtained at the isoelectric points of the protein and the highest in the presence of electrostatic repulsion between the membrane surface and the protein molecules. In the laminar flow regime the critical flux increased with flow velocity, but not any more above this region. An increase in concentration de-creased the critical flux. Hydrophobic membranes showed fouling in all charge conditionsand, furthermore, especially at the beginning of the experiment even at very low transmembrane pressures. Fouling of these membranes was thought to be due to protein adsorption by hydrophobic interactions. The hydrophilic membranes used suffered more from reversible fouling and concentration polarisation than from irreversible foul-ing. They became fouled at higher transmembrane pressures becauseof pore blocking. In this thesis some new aspects on critical flux are presented that are important for ultrafiltration and fractionation of proteins.

Arvometallien selektiivinen erottaminen kloridiliuoksista

Työssä tutkittiin jalometallien selektiivistä erottamista kloridiliuoksista synteettisten polymeerihartsien avulla. Laboratoriokokeissa keskityttiin tutkimaan kullan erottamista hydrofiilisen polymetakrylaattipohjaisen adsorbentin avulla. Lähtökohtana oli platinarikaste, joka sisälsi kullan lisäksi platinaa, palladiumia, hopeaa, kuparia, rautaa, vismuttia, seleeniä ja telluuria. Mittauksissa tutkittiin eri metallien ja puolimetallien adsorptiota hartsiin tasapaino-, kinetiikka- ja kolonnikokeilla. Työssä käytettiin myös adsorption simulointiin monikomponenttierotuksen dynaamiseen mallintamiseen tarkoitettua tietokoneohjelmaa, johon tarvittavat parametrit estimoitiin kokeellisen datan avulla. Tasapainokokeet yhtä metallia sisältäneistä liuoksista osoittivat, että hartsi adsorboi tehokkaasti kultaa kaikissa tutkituissa suolahappopitoisuuksissa (1-6 M). Kulta muodostaa hartsiin hyvin adsorboituvia tetrakloroauraatti(III)ioneja, [AuCl4]-, jotka ovat erittäin stabiileja pieniin kloridipitoisuuksiin saakka. Suolahappopitoisuudella oli merkitystä ainoastaan raudan adsorptioon, joka kasvoi huomattavasti suolahappopitoisuuden noustessa johtuen raudan taipumuksesta muodostaa hyvin adsorboituvia [FeCl4]--ioneja väkevissä suolahappopitoisuuksissa. Muiden tutkittujen alkuaineiden adsorptiot jäivät alhaisiksi kaikilla suolahappopitoisuuksilla. Rikasteliuoksella tehdyt tasapainokokeet osoittivat, että adsorptiokapasiteetti kullalle riippuu voimakkaasti muista läsnäolevista komponenteista. Kilpaileva adsorptio kuvattiin Langmuir-Freundlich-isotermillä. Kolonnikokeet osoittivat, että hartsi adsorboi kullan lisäksi hieman myös rautaa ja telluuria, jotka saatiin kuitenkin eluoitua hartsista täysin 5 M suolahappopesulla ja sitä seuraavalla 1 M suolahappopesulla. Tehokkaaksi liuokseksi kullan desorboimiseen osoittautui asetonin ja 1 M suolahapon seos. Kolonnierotuksen eri vaiheet pystyttiin tyydyttävästi kuvaamaan simulointimallilla.

Rasvaisten jätevesien puhdistus

Rasvaisten jätevesien puhdistus on sitä tuottaville yrityksille kallista ja hankalaa. Nykyisten päästövaatimusten saavuttaminen on perinteisillä jätevedenkäsittelymenetelmillä vaikeaa tai lähes mahdotonta, riippuen käsiteltävän jäteveden ominaisuuksista. Rasvaisen jäteveden käsittelyssä on käytetty mm. laskeutusta, flotaatiota, hydrosykloneja, pisaroitusta, suodatusta sekä biologista käsittelyä. Lisäksi happohydrolyysiä voidaan soveltaa edellä mainittujen menetelmien esikäsittelynä. Useita näitä erotusmenetelmiä voidaan myös tehostaa kemikaalien lisäyksellä. Työn kirjallisuusosassa on käsitelty rasvaisten jätevesien ja emulsioiden kalvosuodatusta ja kalvojen käyttöä pisaroituselementtinä. Tavanomaisessa kalvosuodatuksessa tarkoituksena on erottaa kalvoa läpäisemätön rasvajae ja permeoituva vesijae toisistaan, kun taas pisaroittamisen tarkoituksena on saada dispergoituneen faasin pisarakoko kasvamaan joko kalvon pinnalla tai sen huokosissa. Pisarakoon kasvaessa emulsion stabiilisuus heikkenee ja faasit voidaan helpommin erottaa toisistaan. Työn kokeellisessa osassa tavoitteena oli tutkia kalvosuodatuksen ja erilaisten kalvojen toimivuutta esteröintilaitoksen rasvaisten jätevesien käsittelyssä. Tutkimuksessa käytettiin MW- (GE Osmonics), C30F- (Nadir Filtration), Teflon Typar- (Tetratex) sekä JX-kalvoa (Osmonics Desal). Haastetta työhön syntyi tutkittujen jätevesien ominaisuuksien suuresta vaihtelusta sitä tuottavan laitoksen panostyylisestä toiminnasta johtuen. Lisäksi tutkittiin, onko syöttöliuoksen pH-säädöllä ja laskeutuksella ennen suodatusta merkittävää etua itse kalvosuodatusprosessiin. Kalvotekniikkaa voidaan tämän tutkimuksen perusteella soveltaa myös esteröintilaitoksen rasvaisten jätevesien suodatukseen, ja erityistä etua saadaan jäteveden pH-säädöllä (pH 3) ja laskeutuksella ennen varsinaista suodatusta. Tällaiseen käsittelyyn soveltuu tutkituista kalvoista parhaiten hydrofiilinen regeneroidusta selluloosasta valmistettu C30F-kalvo, jonka etuna on vähäinen foulaantuminen muihin tutkittuihin kalvoihin verrattuna.

Siistausmassan saostuksessa kiekkosuodattimella käytettävän suodatinväliaineen testaus ja kehittäminen

Työn aiheena on siistausmassan saostuksessa käytettävä kiekkosuodatinväliaine ja tarkoituksena selvittää lankamateriaalien ja pinnoitusaineiden vaikutusta väliaineen likaantumisherkkyyteen ja suodatusteknisiin ominaisuuksiin. Siistauslaitosten ongelmana on suodatinväliaineen likaantuminen massassa olevien tahmo- ja painoväripartikkelien johdosta. Tällä hetkellä siistauslaitosten kiekkosuodatinpussien valmistuksessa käytetään pääasiassa polypropeeni- ja polyvinylideenifluoridimonofilamenttilankoja, joiden lianhylkivyys on osoittautunut huonoksi. Uusiksi lankamateriaaleiksi tutkimuksiin valittiin Easy Kleen I, Easy Kleen II, Hyflon, Halar ja Polyesteri. Tulosten perusteella Easy Kleen I ja II monofilamenttilangoista kudotun suodatinkankaan lianhylkivyys on polypropeeni- ja polyvinylideenifluoridimonofilamenttilangoista kudottua kangasta parempi. Suodatusteknisissä ominaisuuksissa ei materiaalien välillä havaittu merkittävää eroa. Easy Kleen monofilamenttilangat näyttävät soveltuvan myös keittokutistumiltaan ja mekaanisilta ominaisuuksiltaan kiekkosuodatinpussien materiaaleiksi. Polypropeeni- ja polyesterimonofilamenettilangoista kudottujen suodatinkankaiden pinnoittamisessa käytettiin hydrofiilisiä ja hydrofobisia pinnoitusaineita. Tulosten perusteella on mahdollista parantaa suodatinkankaan lianhylkivyyttä pinnoittamalla. Pinnoitettu kangas on myös suodatusteknisiltä ominaisuuksiltaan toimiva. Ongelmaksi suodatinkankaiden pinnoittamisessa saattaa kuitenkin muodostua pinnoituslämpötila, jossa kangas kutistuu asennuskelvottomaksi.

Otsonin käyttö paperin ja kartongin valmistuksen kiertovesien mikrobiologisen tilan hallintaan

Diplomityössä tutkittiin otsonin käytön soveltuvuutta ja etsittiin optimaalista soveltamistapaa kartonki- ja paperikoneen kiertoveden mikrobiologisen tilan hallintaan. Kirjallisuusosassa selvitettiin otsonin tuotannon nykytekniikkaa sekä otettiin selvää saatavilla olevista kapasiteetiltaan riittävistä otsonigeneraattoreista. Kirjallisuuden perusteella selvitettiin myös otsonin reaktioita paperi- ja kartonkikoneen kiertovesissä olevien orgaanisten ja epäorgaanisten aineiden kanssa. Lisäksi käsiteltiin otsonin käytön eri sovelluksia vedenpuhdistuksessa sekä perehdyttiin aikaisemmin tehtyihin tutkimuksiin otsonin käytöstä mikrobitorjuntaan paperi- ja kartonkikoneiden kiertovesistä. Kokeellisessa osassa määritettiin sopiva otsoniannos valkaisematonta sellua käyttävän koneen kiekkosuotimen kirkkaalle ja samealle suodokselle. Vesien otsonointi suoritettiin otsonipilotlaitteistolla. Työssä tutkittiin otsonoinnin vaikutusta kiertoveden mikrobiologisiin ja kemiallisiin ominaisuuksiin. Lisäksi tarkasteltiin kiertoveden otsonoinnin vaikutuksia koepaperikoneella valkaisemattomasta sel-lusta ja hylkymassasta valmistettujen lopputuotteiden laatuun. Työssä arvioitiin myös otsonin käytön mahdollisuutta osittain korvaamaan jo käytössä olevia hapettavia biosidejä. Samealle suodokselle sopivaksi otsoniannokseksi osoittautui 120 mg O3/l (0,3 mg O3/mg CODCr) ja kirkkaalle suodokselle riittävä annos olisi 60 mg O3/l (0,2 mg/mg CODCr). Näillä annoksilla kiertoveden mikrobireduktiot olivat 98–100 %. Kiertoveden hapetuskyky kasvoi 9-14 % ja pH laski yhdellä yksiköllä otsonoinnin vaikutuksesta. Kiertoveden kemiallisiin ominaisuuksiin otsonoinnilla oli edullinen vaikutus, sillä veden sameus, kiintoaine- ja CODCr-pitoisuudet laskivat. Koepaperikoneella havaittiin perälaatikon ilmapitoisuuden vähentyneen jopa 49 % käytettäessä ot-sonoitua kiertovettä. Mikrobiologiset analyysit suoritettiin koepaperikoneen massalle, viiravedelle ja lopputuotteelle. Tutkimusten perusteella mikrobientorjunnan kannalta parhaimmaksi otsonin annos-telupaikaksi osoittautui samea suodos. Massan, viiraveden ja lopputuotteen mikrobimäärät alenivat selvästi. Kemialliset analyysit osoittivat, että kirkasta suodosta käytettäessä oli koepaperikoneen vii-raveden kemiallinen tila parantunut LK-aineen muuttuessa hydrofiilisemmäksi ja sen sitoutumisky-vyn parantuessa. Samealla suodoksella ei muutosta havaittu. Valkaisemattomasta sellusta ja päällystetystä hylystä koepaperikoneella valmistettujen lopputuotteiden lujuus- ja aistinvaraisissa ominaisuuksissa ei tapahtunut merkittävää muutosta. Tulosten perusteella otsonia voisi käyttää korvaamaan hinnaltaan kalliimpia hapettavia biosidejä. Otsonin etuna on, ettei sille resistenttejä mikrobikantoja ole. Kirjallisuuden perusteella otsonin heikkoutena on sen tehon paikallisuus eli otsonin lisänä on käytettävä jotain muuta sekundääristä biosidia ylläpitämään matala mikrobitaso otsonoinnin jälkeen.

Process intensification: From optimised flow patterns to microprocess technology

This thesis is focused on process intensification. Several significant problems and applications of this theme are covered. Process intensification is nowadays one of the most popular trends in chemical engineering and attempts have been made to develop a general, systematic methodology for intensification. This seems, however, to be very difficult, because intensified processes are often based on creativity and novel ideas. Monolith reactors and microreactors are successful examples of process intensification. They are usually multichannel devices in which a proper feed technique is important for creating even fluid distribution into the channels. Two different feed techniques were tested for monoliths. In the first technique a shower method was implemented by means of perforated plates. The second technique was a dispersion method using static mixers. Both techniques offered stable operation and uniform fluid distribution. The dispersion method enabled a wider operational range in terms of liquid superficial velocity. Using dispersion method, a volumetric gas-liquid mass transfer coefficient of 2 s-1 was reached. Flow patterns play a significant role in terms of the mixing performance of micromixers. Although the geometry of a T-mixer is simple, channel configurations and dimensions had a clear effect on mixing efficiency. The flow in the microchannel was laminar, but the formation of vortices promoted mixing in micro T-mixers. The generation of vortices was dependent on the channel dimensions, configurations and flow rate. Microreactors offer a high ratio of surface area to volume. Surface forces and interactions between fluids and surfaces are, therefore, often dominant factors. In certain cases, the interactions can be effectively utilised. Different wetting properties of solid materials (PTFE and stainless steel) were applied in the separation of immiscible liquid phases. A micro-scale plate coalescer with hydrophilic and hydrophobic surfaces was used for the continuous separation of organic and aqueous phases. Complete phase separation occurred in less than 20 seconds, whereas the separation time by settling exceeded 30 min. Fluid flows can be also intensified in suitable conditions. By adding certain additives into turbulent fluid flow, it was possible to reduce friction (drag) by 40 %. Drag reduction decreases frictional pressure drop in pipelines which leads to remarkable energy savings and decreases the size or number of pumping facilities required, e.g., in oil transport pipes. Process intensification enables operation often under more optimal conditions. The consequent cost savings from reduced use of raw materials and reduced waste lead to greater economic benefits in processing.

Pretreatment in membrane filtration of wood hydrolysate

Interest in recovery of valuable components from process streams has increased in recent years. Purpose of biorefinery is to utilize components that otherwise would go to waste. Hemicelluloses, for example, could be utilized in production of many valuable products. One possible way to separate and fractionate hemicelluloses is membrane filtration. In the literature part of this work membrane fouling in filtration processes of pulp and paper process- and wastewaters was investigated. Especially purpose was to find out the possible fouling compounds, after which facilities to remove or modify such components less harmful were studied. In the experimental part different pretreatment methods, mainly to remove or degrade lignin from wood hydrolysate, were studied. In addition, concentration of hemicelluloses and separation from lignin were examined with two ultrafiltration membranes; UFX5 and RC70PP. Changes in feed solution, filtration capacity and fouling of membranes were used to evaluate the effects of pretreatment methods. Changes in hydrolysate composition were observed with different analysis methods. Filtration of hydrolysate proved to be challenging, especially with the UFX5 membrane. The more hydrophilic RC70PP membrane did not seem to be fouled as severely as the UFX5 membrane, according to pure water flux measurements. The UFX5 membrane retained hemicelluloses rather well, but problems arose from rapid flux decline resulting from concentration polarization and fouling of membrane. Most effective pretreatment methods in the case with the UFX5 membrane proved to be prefiltration with the RC70PP membrane, activated carbon adsorption and photocatalytic oxidation using titanium dioxide and UV radiation. An additional experiment with PHW extract showed that pulsed corona discharge treatment degraded lignin quite efficiently and thus improved filtration capacity remarkably, even over six times compared to the filtration with untreated extract.

Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

Enhancing performance of paper coatings by tailor-made plastic pigments

The paper industry is constantly looking for new ideas for improving paper products while competition and raw material prices are increasing. Many paper products are pigment coated. Coating layer is the top layer of paper, thus by modifying coating pigment also the paper itself can be altered and value added to the final product. In this thesis, synthesis of new plastic and hybrid pigments and their performance in paper and paperboard coating is reported. Two types of plastic pigments were studied: core-shell latexes and solid beads of maleimide copolymers. Core-shell latexes with partially crosslinked hydrophilic polymer core of poly(n-butyl acrylate-co-methacrylic acid) and a hard hydrophobic polystyrene shell were prepared to improve the optical properties of coated paper. In addition, the effect of different crosslinkers was analyzed and the best overall performance was achieved by the use of ethylene glycol dimethacrylate (EGDMA). Furthermore, the possibility to modify core-shell latex was investigated by introducing a new polymerizable optical brightening agent, 1-[(4-vinylphenoxy)methyl]-4-(2-henylethylenyl)benzene which gave promising results. The prepared core-shell latex pigments performed smoothly also in pilot coating and printing trials. The results demonstrated that by optimizing polymer composition, the optical and surface properties of coated paper can be significantly enhanced. The optimal reaction conditions were established for thermal imidization of poly(styrene-co-maleimide) (SMI) and poly(octadecene-co-maleimide) (OMI) from respective maleic anhydride copolymer precursors and ammonia in a solvent free process. The obtained aqueous dispersions of nanoparticle copolymers exhibited glass transition temperatures (Tg) between 140-170ºC and particle sizes from 50-230 nm. Furthermore, the maleimide copolymers were evaluated in paperboard coating as additional pigments. The maleimide copolymer nanoparticles were partly imbedded into the porous coating structure and therefore the full potential of optical property enhancement for paperboard was not achieved by this method. The possibility to modify maleimide copolymers was also studied. Modifications were carried out via N-substitution by replacing part of the ammonia in the imidization reaction with amines, such as triacetonediamine (TAD), aspartic acid (ASP) and fluorinated amines (2,2,2- trifluoroethylamine, TFEA and 2,2,3,3,4,4,4-heptafluorobuthylamine, HFBA). The obtained functional nanoparticles varied in size between 50-217 nm and their Tg from 150-180ºC. During the coating process the produced plastic pigments exhibited good runnability. No significant improvements were achieved in light stability with TAD modified copolymers whereas nanoparticles modified with aspartic acid and those containing fluorinated groups showed the desired changes in surface properties of the coated paperboard. Finally, reports on preliminary studies with organic-inorganic hybrids are presented. The hybrids prepared by an in situ polymerization reaction consisted of 30 wt% poly(styrene- co-maleimide) (SMI) and high levels of 70 wt% inorganic components of kaolin and/or alumina trihydrate. Scanning Electron Microscopy (SEM) images and characterization by Fourier Transform Infrared Spcetroscopy (FTIR) and X-Ray Diffraction (XRD) revealed that the hybrids had conventional composite structure and inorganic components were covered with precipitated SMI nanoparticles attached to the surface via hydrogen bonding. In paper coating, the hybrids had a beneficial effect on increasing gloss levels.

Upconverting Phosphor Technology: Exceptional Photoluminescent Properties Light Up Homogeneous Bioanalytical Assays

The aim of the present study was to demonstrate the wide applicability of the novel photoluminescent labels called upconverting phosphors (UCPs) in proximity-based bioanalytical assays. The exceptional features of the lanthanide-doped inorganic UCP compounds stem from their capability for photon upconversion resulting in anti-Stokes photoluminescence at visible wavelengths under near-infrared (NIR) excitation. Major limitations related to conventional photoluminescent labels are avoided, rendering the UCPs a competitive next-generation label technology. First, the background luminescence is minimized due to total elimination of autofluorescence. Consequently, improvements in detectability are expected. Second, at the long wavelengths (>600 nm) used for exciting and detecting the UCPs, the transmittance of sample matrixes is significantly greater in comparison with shorter wavelengths. Colored samples are no longer an obstacle to the luminescence measurement, and more flexibility is allowed even in homogeneous assay concepts, where the sample matrix remains present during the entire analysis procedure, including label detection. To transform a UCP particle into a biocompatible label suitable for bioanalytical assays, it must be colloidal in an aqueous environment and covered with biomolecules capable of recognizing the analyte molecule. At the beginning of this study, only UCP bulk material was available, and it was necessary to process the material to submicrometer-sized particles prior to use. Later, the ground UCPs, with irregular shape, wide size-distribution and heterogeneous luminescence properties, were substituted by a smaller-sized spherical UCP material. The surface functionalization of the UCPs was realized by producing a thin hydrophilic coating. Polymer adsorption on the UCP surface is a simple way to introduce functional groups for bioconjugation purposes, but possible stability issues encouraged us to optimize an optional silica-encapsulation method which produces a coating that is not detached in storage or assay conditions. An extremely thin monolayer around the UCPs was pursued due to their intended use as short-distance energy donors, and much attention was paid to controlling the thickness of the coating. The performance of the UCP technology was evaluated in three different homogeneous resonance energy transfer-based bioanalytical assays: a competitive ligand binding assay, a hybridization assay for nucleic acid detection and an enzyme activity assay. To complete the list, a competitive immunoassay has been published previously. Our systematic investigation showed that a nonradiative energy transfer mechanism is indeed involved, when a UCP and an acceptor fluorophore are brought into close proximity in aqueous suspension. This process is the basis for the above-mentioned homogeneous assays, in which the distance between the fluorescent species depends on a specific biomolecular binding event. According to the studies, the submicrometer-sized UCP labels allow versatile proximity-based bioanalysis with low detection limits (a low-nanomolar concentration for biotin, 0.01 U for benzonase enzyme, 0.35 nM for target DNA sequence).

Identification of extractives and polysaccharides as foulants in membrane filtration of pulp and paper mill effluents

The search for new renewable materials has intensified in recent years. Pulp and paper mill process streams contain a number of potential compounds which could be used in biofuel production and as raw materials in the chemical, food and pharmaceutical industries. Prior to utilization, these compounds require separation from other compounds present in the process stream. One feasible separation technique is membrane filtration but to some extent, fouling still limits its implementation in pulp and paper mill applications. To mitigate fouling and its effects, foulants and their fouling mechanisms need to be well understood. This thesis evaluates fouling in filtration of pulp and paper mill process streams by means of polysaccharide model substance filtrations and by development of a procedure to analyze and identify potential foulants, i.e. wood extractives and carbohydrates, from fouled membranes. The model solution filtration results demonstrate that each polysaccharide has its own fouling mechanism, which also depends on the membrane characteristics. Polysaccharides may foul the membranes by adsorption and/or by gel/cake layer formation on the membrane surface. Moreover, the polysaccharides interact, which makes fouling evaluation of certain compound groups very challenging. Novel methods to identify wood extractive and polysaccharide foulants are developed in this thesis. The results show that it is possible to extract and identify wood extractives from membranes fouled in filtration of pulp and paper millstreams. The most effective solvent was found to be acetone:water (9:1 v/v) because it extracted both lipophilic extractives and lignans at high amounts from the fouled membranes and it was also non-destructive for the membrane materials. One hour of extraction was enough to extract wood extractives at high amounts for membrane samples with an area of 0.008 m2. If only qualitative knowledge of wood extractives is needed a simplified extraction procedure can be used. Adsorption was the main fouling mechanism in extractives-induced fouling and dissolved fatty and resin acids were mostly the reason for the fouling; colloidal fouling was negligible. Both process water and membrane characteristics affected extractives-induced fouling. In general, the more hydrophilic regenerated cellulose (RC) membrane fouled less that the more hydrophobic polyethersulfone (PES) and polyamide (PA) membranes independent of the process water used. Monosaccharide and uronic acid units could also be identified from the fouled synthetic polymeric membranes. It was impossible to analyze all monosaccharide units from the RC membrane because the analysis result obtained contained degraded membrane material. One of the fouling mechanisms of carbohydrates was adsorption. Carbohydrates were not potential adsorptive foulants to the sameextent as wood extractives because their amount in the fouled membranes was found to be significantly lower than the amount of wood extractives.

Ultrasuodatuskalvon modifiointi paineen, lämpötilan ja emäksen avulla

Työssä tutkittiin polymeerisen ultrasuodatuskalvon modifiointimahdollisuuksia prosessiolosuhteita muuttamalla. Kalvon modifioimisella pyritään sen suodatusominaisuuksien muuttumiseen, joka voi lisätä kalvon käyttökohteita ja parantaa kalvon soveltuvuutta tiettyjen yhdisteiden suodatukseen. Hydrofiilisiä, tiukkoja polymeerisiä ultrasuodatuskalvoja on kaupallisesti saatavilla vähän, joten työssä tutkittiin niiden valmistusta modifioimalla markkinoilla olevaa, löysempää, hydrofiilistä, polymeeristä ultrasuodatuskalvoa. Ultrasuodatuskalvo modifioitiin paineen, lämpötilan ja emäksen avulla. Modifioinnin aiheuttamat muutokset voidaan jakaa pysyviin, osittain palautuviin tai palautuviin muutoksiin. Kalvon rakenteen muuttuessa pysyvästi voidaan kalvo modifioida ennen suodatuksen aloittamista. Tällöin modifioinnissa käytetyt olosuhteet eivät vaikuta suodatukseen kuten muissa tapauksissa. Modifioinnin vaikutusta kalvoon voidaan analysoida eri menetelmillä. Näitä ovat esimerkiksi elektronimikroskopia ja kalvon vuon tai retention analysointi. Mikroskooppikuvia ei voida ottaa suodatuksen aikana, vaan kalvosta saada tietoa ainoastaan alku- ja lopputilanteissa suodatusolosuhteista poistettuna. Vuon ja retention avulla saadaan reaaliaikaista tietoa modifioidun kalvon suodatuskapasiteetin ja erotuskyvyn muutoksista. Työssä modifioinnin vaikutusta seurattiin vuo- ja retentiomittausten avulla ja kalvon rakenteessa tapahtuvia muutoksia tutkittiin pyyhkäisyelektronimikroskooppikuvien ja mikrometrimittausten avulla. Korkeampaa painetta tai lämpötilaa käytettäessä havaittiin vuon alenevan modifioitaessa enemmän kuin matalammissa paineissa tai lämpötiloissa. Korkeampi puristuslämpötila kasvatti myös retentiota. Modifiointiolosuhteiden ollessa emäksisiä aleni permeabiliteetti neutraaleissa olosuhteissa tehtyä puristusta enemmän. Myös retentio aleni emäksen avulla tehdyssä modifioinnissa. Kalvon rakenteessa tapahtuneiden muutosten palautuminen riippui modifiointilämpötilasta, korkeassa lämpötilassa modifioidussa kalvossa palautumista ei tapahtunut. Modifioinnin aiheuttamat kalvojen paksuuden muutokset tukivat retentio- ja vuomittauksia. Pyyhkäisyelektronimikroskooppikuvista voitiin havaita kalvon huokosrakenteen puristuneen modifioinnin aikana.

Kytkentäaineet puumuovikomposiiteissa

Puumuovikomposiittien valmistuksessa yhdistetään kaksi toisistaan eroavaa materiaalia jolloin saadaan aikaan materiaalien ominaisuuksien ainutlaatuinen yhdistelmä. Polymeerimateriaaleina käytetään pääasiassa erilaisia kestomuoveja. Kuitumateriaaleina voidaan käyttää puujauhetta, sahanpurua, paperin- ja kartongin valmistuksessa käytettävää sellua, nanoselluloosaa tai muita puukuitumateriaaleja. Polaarisen puukuidun ja polaarittoman muovimateriaalin välinen materiaalien rajapinnan adheesio on yleensä riittämätöntä, mikä vaikuttaa lopputuotteen ominaisuuksien heikkenemiseen. Kyseinen ongelma on pyritty ratkaisemaan käyttämällä erilaisia kytkentäaineita. Tässä työssä keskitytään käsittelemään erilaisia puumuovikomposiittien kytkentäaineita, niiden toimintaa sekä vaikutuksia lopputuotteeseen. Lisäksi työssä esitellään myös puumuovikomposiittien valmistusmateriaaleja ja valmistusprosesseja.

Effects of cytochrome P450 enzyme inhibitors and inducers on the metabolism of S-ketamine

The human body eliminates foreign compounds primarily by metabolizing them to hydrophilic forms to facilitate effective excretion through the kidneys. Cytochrome P450 (CYP) enzymes in the liver and intestine contribute to the metabolism of many drugs. Pharmacokinetic drugdrug interactions occur if the activity of CYPs are inhibited or induced by another drug. Prescribing multiple drugs to the improve effectiveness of therapy or to treat coexisting diseases is a common practice in clinical medicine. Polypharmacy predisposes patients to adverse effects because of the profound unpredictability in CYP enzymatic-mediated drug metabolism. S-ketamine is a phencyclidine derivative which functions as an antagonist of the N-methyl-Daspartate (NMDA) receptor in the central nervous system. It is a unique anaesthetic producing “dissociative anaesthesia” in high doses and analgesia in low doses. Studies with human liver microsomes suggest that ketamine is metabolized primarily via CYP3A4 and CYP2B6 enzymes. In this thesis, in healthy volunteers, randomized and controlled cross-over studies were conducted to investigate the effects of different CYP inducers and inhibitors on the pharmacokinetics and pharmacodynamics of oral and intravenous S-ketamine. The plasma concentrations of ketamine and its metabolite, norketamine, were determined at different timepoints over a 24 hour period. Other pharmacodynamic variables were examined for 12 hours. Results of these studies showed that the inhibition of the CYP3A4 pathway by clarithromycin or grapefruit juice increased the exposure to oral S-ketamine by 2.6- and 3.0-fold. Unexpectedly, CYP3A4 inhibition by itraconazole caused no significant alterations in the plasma concentrations of oral S-ketamine. CYP3A4 induction by St. John´s wort or rifampicin decreased profoundly the concentrations of oral S-ketamine. However, after rifampicin, there were no significant differences in the plasma concentrations of S-ketamine when it was administered intravenously. This demonstrated that rifampicin inhibited the metabolism of Sketamine at the intestinal level. When CYP2B6 was inhibited by ticlopidine, there was a 2.4- fold increase in the exposure of S-ketamine. These studies demonstrated that low dose oral Sketamine is metabolized both via CYP3A4 and CYP2B6 pathways. The concomitant use of drugs that affect CYP3A4 or CYP2B6, during oral S-ketamine treatment, may cause clinically significant drug-drug interactions.