Comparisons of Estimates of Annual Exceedance-Probability Discharges for Small Drainage Basins in Iowa, Based on Data through Water Year 2013, TR-678, 2015

Traditionally, the Iowa Department of Transportation has used the Iowa Runoff Chart and single-variable regional-regression equations (RREs) from a U.S. Geological Survey report (published in 1987) as the primary methods to estimate annual exceedance-probability discharge (AEPD) for small (20 square miles or less) drainage basins in Iowa. With the publication of new multi- and single-variable RREs by the U.S. Geological Survey (published in 2013), the Iowa Department of Transportation needs to determine which methods of AEPD estimation provide the best accuracy and the least bias for small drainage basins in Iowa. Twenty five streamgages with drainage areas less than 2 square miles (mi2) and 55 streamgages with drainage areas between 2 and 20 mi2 were selected for the comparisons that used two evaluation metrics. Estimates of AEPDs calculated for the streamgages using the expected moments algorithm/multiple Grubbs-Beck test analysis method were compared to estimates of AEPDs calculated from the 2013 multivariable RREs; the 2013 single-variable RREs; the 1987 single-variable RREs; the TR-55 rainfall-runoff model; and the Iowa Runoff Chart. For the 25 streamgages with drainage areas less than 2 mi2, results of the comparisons seem to indicate the best overall accuracy and the least bias may be achieved by using the TR-55 method for flood regions 1 and 3 (published in 2013) and by using the 1987 single-variable RREs for flood region 2 (published in 2013). For drainage basins with areas between 2 and 20 mi2, results of the comparisons seem to indicate the best overall accuracy and the least bias may be achieved by using the 1987 single-variable RREs for the Southern Iowa Drift Plain landform region and for flood region 3 (published in 2013), by using the 2013 multivariable RREs for the Iowan Surface landform region, and by using the 2013 or 1987 single-variable RREs for flood region 2 (published in 2013). For all other landform or flood regions in Iowa, use of the 2013 single-variable RREs may provide the best overall accuracy and the least bias. An examination was conducted to understand why the 1987 single-variable RREs seem to provide better accuracy and less bias than either of the 2013 multi- or single-variable RREs. A comparison of 1-percent annual exceedance-probability regression lines for hydrologic regions 1–4 from the 1987 single-variable RREs and for flood regions 1–3 from the 2013 single-variable RREs indicates that the 1987 single-variable regional-regression lines generally have steeper slopes and lower discharges when compared to 2013 single-variable regional-regression lines for corresponding areas of Iowa. The combination of the definition of hydrologic regions, the lower discharges, and the steeper slopes of regression lines associated with the 1987 single-variable RREs seem to provide better accuracy and less bias when compared to the 2013 multi- or single-variable RREs; better accuracy and less bias was determined particularly for drainage areas less than 2 mi2, and also for some drainage areas between 2 and 20 mi2. The 2013 multi- and single-variable RREs are considered to provide better accuracy and less bias for larger drainage areas. Results of this study indicate that additional research is needed to address the curvilinear relation between drainage area and AEPDs for areas of Iowa.

Strengthening of Existing Single Span Steel Beam and Concrete Deck Bridges, HR-238, Part II, 1985

The unifying objective of Phases I and II of this study was to determine the feasibility of the post-tensioning strengthening method and to implement the technique on two composite bridges in Iowa. Following completion of these two phases, Phase III was undertaken and is documented in this report. The basic objectives of Phase III were further monitoring bridge behavior (both during and after post-tensioning) and developing a practical design methodology for designing the strengthening system under investigation. Specific objectives were: to develop strain and force transducers to facilitate the collection of field data; to investigate further the existence and effects of the end restraint on the post-tensioning process; to determine the amount of post-tensioning force loss that occurred during the time between the initial testing and the retesting of the existing bridges; to determine the significance of any temporary temperature-induced post-tensioning force change; and to develop a simplified design methodology that would incorporate various variables such as span length, angle-of-skew, beam spacing, and concrete strength. Experimental field results obtained during Phases II and III were compared to the theoretical results and to each other. Conclusions from this research are as follows: (1) Strengthening single-span composite bridges by post-tensioning is a viable, economical strengthening technique. (2) Behavior of both bridges was similar to the behavior observed from the bridges during field tests conducted under Phase II. (3) The strain transducers were very accurate at measuring mid-span strain. (4) The force transducers gave excellent results under laboratory conditions, but were found to be less effective when used in actual bridge tests. (5) Loss of post-tensioning force due to temperature effects in any particular steel beam post-tensioning tendon system were found to be small. (6) Loss of post-tensioning force over a two-year period was minimal. (7) Significant end restraint was measured in both bridges, caused primarily by reinforcing steel being continuous from the deck into the abutments. This end restraint reduced the effectiveness of the post-tensioning but also reduced midspan strains due to truck loadings. (8) The SAP IV finite element model is capable of accurately modeling the behavior of a post-tensioned bridge, if guardrails and end restraints are included in the model. (9) Post-tensioning distribution should be separated into distributions for the axial force and moment components of an eccentric post-tensioning force. (10) Skews of 45 deg or less have a minor influence on post-tensioning distribution. (11) For typical Iowa three-beam and four-beam composite bridges, simple regression-derived formulas for force and moment fractions can be used to estimate post-tensioning distribution at midspan. At other locations, a simple linear interpolation gives approximately correct results. (12) A simple analytical model can accurately estimate the flexural strength of an isolated post-tensioned composite beam.

Promising Directions: Programs that Serve Iowa Girls in a Single-Sex Environment, September 2000

Promising Directions: Programs that Serve Iowa Girls in a Single-Sex Environment - a resource guide project of the Iowa Gender-Specific Services Task Force. Produced by the Iowa Commission on the Status of Women.

State of Iowa Single Audit Report, June 30, 2003

State Agency Audit Report Independent Auditor's Reports Iowa Comprehensive Annual Financial Report - Financial Section Schedule of expenditures of Federal Awards Schedule of findings and questioned costs

State of Iowa, Single Audit Report, Independent Auditor's Reports, Iowa Comprehensive Annual Financial Report - Financial Section, Schedule of Expenditures of Federal Awards, Schedule of Findings and Questioned Costs, June 30, 2004

State Audit Reports

U.S. Universities’ Net Returns from Patenting and Licensing: A Quantile Regression Analysis, September 2006

In line with the rights and incentives provided by the Bayh-Dole Act of 1980, U.S. universities have increased their involvement in patenting and licensing activities through their own technology transfer offices. Only a few U.S. universities are obtaining large returns, however, whereas others are continuing with these activities despite negligible or negative returns. We assess the U.S. universities’ potential to generate returns from licensing activities by modeling and estimating quantiles of the distribution of net licensing returns conditional on some of their structural characteristics. We find limited prospects for public universities without a medical school everywhere in their distribution. Other groups of universities (private, and public with a medical school) can expect significant but still fairly modest returns only beyond the 0.9th quantile. These findings call into question the appropriateness of the revenue-generating motive for the aggressive rate of patenting and licensing by U.S. universities.

State of Iowa’s Single Audit Report for the year ended June 30, 2006

State of Iowa’s Single Audit Report for the year ended June 30, 2006

State of Iowa’s Single Audit Report for the year ended June 30, 2007

State of Iowa’s Single Audit Report for the year ended June 30, 2007

State of Iowa’s Single Audit Report for the year ended June 30, 2005

State of Iowa’s Single Audit Report for the year ended June 30, 2005

State of Iowa’s Single Audit Report for the year ended June 30, 2008

State of Iowa’s Single Audit Report for the year ended June 30, 2008

State of Iowa’s Single Audit Report for the year ended June 30, 2009

State of Iowa’s Single Audit Report for the year ended June 30, 2009

The Rebuild Iowa Office is a part of the State of Iowa and, as such, has been included in our audits of the State’s Comprehensive Annual Financial Report (CAFR) and the State’s Single Audit Report for the year ended June 30, 2009

The Rebuild Iowa Office is a part of the State of Iowa and, as such, has been included in our audits of the State’s Comprehensive Annual Financial Report (CAFR) and the State’s Single Audit Report for the year ended June 30, 2009

State of Iowa’s Single Audit Report for the year ended June 30, 2010

State of Iowa’s Single Audit Report for the year ended June 30, 2010

Design and Evaluation of a Single-Span Bridge Using Ultra- High Performance Concrete, September 2009

Research presented herein describes an application of a newly developed material called Ultra-High Performance Concrete (UHPC) to a single-span bridge. The two primary objectives of this research were to develop a shear design procedure for possible code adoption and to provide a performance evaluation to ensure the viability of the first UHPC bridge in the United States. Two other secondary objectives included defining of material properties and understanding of flexural behavior of a UHPC bridge girder. In order to obtain information in these areas, several tests were carried out including material testing, large-scale laboratory flexure testing, large-scale laboratory shear testing, large-scale laboratory flexure-shear testing, small-scale laboratory shear testing, and field testing of a UHPC bridge. Experimental and analytical results of the described tests are presented. Analytical models to understand the flexure and shear behavior of UHPC members were developed using iterative computer based procedures. Previous research is referenced explaining a simplified flexural design procedure and a simplified pure shear design procedure. This work describes a shear design procedure based on the Modified Compression Field Theory (MCFT) which can be used in the design of UHPC members. Conclusions are provided regarding the viability of the UHPC bridge and recommendations are made for future research.

State of Iowa’s Single Audit Report for the year ended June 30, 2011

State of Iowa’s Single Audit Report for the year ended June 30, 2011