Investigation of Plastic Pipes for Highway Applications, HR-373A, Phase II, 1997

It is generally accepted that high density polyethylene pipe (HDPE) performs well under live loads with shallow cover, provided the backfill is well compacted. Although industry standards require carefully compacted backfill, poor inspection and/or faulty construction may result in soils that provide inadequate restraint at the springlines of the pipes thereby causing failure. The objectives of this study were: 1) to experimentally define a lower limit of compaction under which the pipes perform satisfactorily, 2) to quantify the increase in soil support as compaction effort increases, 3) to evaluate pipe response for loads applied near the ends of the buried pipes, 4) to determine minimum depths of cover for a variety of pipes and soil conditions by analytically expanding the experimental results through the use of the finite element program CANDE. The test procedures used here are conservative especially for low-density fills loaded to high contact stresses. The failures observed in these tests were the combined effect of soil bearing capacity at the soil surface and localized wall bending of the pipes. Under a pavement system, the pipes' performance would be expected to be considerably better. With those caveats, the following conclusions are drawn from this study. Glacial till compacted to 50% and 80% provides insufficient support; pipe failureoccurs at surface contact stresses lower than those induced by highway trucks. On the other hand, sand backfill compacted to more than 110 pcf (17.3 kN/m3) is satisfactory. The failure mode for all pipes with all backfills is localized wall bending. At moderate tire pressures, i.e. contact stresses, deflections are reduced significantly when backfill density is increased from about 50 pcf (7.9 kN/m^3) to 90 pcf (14.1 kN/m^3). Above that unit weight, little improvement in the soil-pipe system is observed. Although pipe stiffness may vary as much as 16%, analyses show that backfill density is more important than pipe stiffness in controlling both deflections at low pipe stresses and at the ultimate capacity of the soil-pipe system. The rate of increase in ultimate strength of the system increases nearly linearly with increasing backfill density. When loads equivalent to moderate tire pressures are applied near the ends of the pipes, pipe deflections are slighly higher than when loaded at the center. Except for low density glacial till, the deflections near the ends are not excessive and the pipes perform satisfactorily. For contact stresses near the upper limit of truck tire pressures and when loaded near the end, pipes fail with localized wall bending. For flowable fill backfill, the ultimate capacity of the pipes is nearly doubled and at the upper limit of highway truck tire pressures, deflections are negligible. All pipe specimens tested at ambient laboratory room temperatures satisfied AASHTO minimum pipe stiffness requirements at 5% deflection. However, nearly all specimens tested at elevated pipe surface temperatures, approximately 122°F (50°C), failed to meet these requirements. Some HDPE pipe installations may not meet AASHTO minimum pipe stiffness requirements when installed in the summer months (i.e. if pipe surface temperatures are allowed to attain temperatures similar to those tested here). Heating of any portion of the pipe circumference reduced the load carrying capacity of specimens. The minimum soil cover depths, determined from the CANOE analysis, are controlled by the 5% deflection criterion. The minimum soil cover height is 12 in. (305 mm). Pipes with the poor silt and clay backfills with less than 85% compaction require a minimum soil cover height of 24 in. (610 mm). For the sand at 80% compaction, the A36 HDPE pipe with the lowest moment of inertia requires a minimum of 24 in. (610 mm) soil cover. The C48 HDPE pipe with the largest moment of inertia and all other pipes require a 12 in. (305 mm) minimum soil cover.

Report Recycled Content Plastic Bag and Soy Inks, Iowa Department of Transportation, 2003

Report to Margaret Thompson, Chief Clerk, about Recycled Content Plastic Bag and Soy Inks.

Report Recycled Content Plastic Bag and Soy Inks, Iowa Department of Transportation, 2002

Report to Margaret Thompson, Chief Clerk, about Recycled Content Plastic Bag and Soy Inks.

Recycled Content Plastic Bag and Soy Inks Report, 2004

Report to Margaret Thompson, Chief Clerk, about Recycled Content Plastic Bag and Soy Inks.

Tariff Equivalent of Technical Barriers to Trade with Imperfect Substitution and Trade Costs, November 2005

The price-wedge method yields a tariff-equivalent estimate of technical barriers to trade (TBT). An extension of this method accounts for imperfect substitution between domestic and imported goods and incorporates recent findings on trade costs. We explore the sensitivity of this revamped TBT estimate to its key determinants (substitution elasticity, preference for home good, and trade cost). We use the augmented approach to investigate the ongoing US-Japan apple trade dispute and find that removing the Japanese TBT would yield limited export gains to the United States. We then draw policy implications of our findings.

Recycled Content Plastic Bag and Soy Inks Report, 2005

Report to Margaret Thomson, Chief Clerk, about Recycled Content Plastic Bag and Soy Inks.

Recycled Content Plastic Bag and Soy Inks Report, FY 2006

Report to Margaret Thomson, Chief Clerk, about Recycled Content Plastic Bag and Soy Inks.

FY 07 Recycled Content Plastic Bag and Soy Inks Report

As required in Iowa Code section 307.21, this is a summary of purchasing activity for soy-based inks and recycled content trash bags. The figures are for fiscal year 2007.

FY 08 Recycled Content Plastic Bags and Soy Inks Report

As required in Iowa Code section 307.21, the Iowa Department of Transportation submits the following summary of purchasing activity for soy based inks and recycled trash bags. The figures are for Fiscal Year 2008.

FY 09 Recycle Content Plastic Bag and Soy Inks Report

As required by Iowa Code section 307.21, figures for Fiscal Year 2009 for purchasing activity for soy-based inks and recycled content trash bags.

FY10 Recycled Content Plastic Bag and Soy Inks Report

As required by Iowa Code section 37.21, the following is a summary of purchasing activities for soy-based inks and recycled content plastic trash bags. The figures are for Fiscal Year 2010. The department currently has no equipment which will operate with soy ink. Iowa Code section 8A.315 required that a minimum of 50 percent of garbage can liner purchases shall be recycled content plastic garbage can liners. The department purchased $51.478.04 worth of recycled content plastic garbage can liners. The represents 93.9 percent of garbage can liners purchased.

FY 11 Recycled Content Plastic Bag and Soy Inks Report, January 30, 2012

As required by Iowa Code section 307.21, the following report was submitted related to the purchase of soy based inks and recycled content trash bags.

FY12 Recycled Content Plastic Bag and Soy Inks report

This report summarizes the purchasing activity for soy based inks and recycled content trash bags for the Iowa DOT.

Missouri River Flood Coordination Task Force Report, September 25, 2011

The Missouri River floods of 2011 will go down in history as the longest duration flooding event this state has seen to date. The combination of above normal snowfall in the upper Missouri River basin followed by the equivalent of nearly one year’s worth of rainfall in May created an above normal runoff situation which filled the Missouri River and the six main reservoirs within the basin. Compounding this problem was colder than normal temperatures which kept much of the snowpack in the upper basin on the ground longer into the spring, setting the stage for this historic event. The U.S. Army Corps of Engineers (USACE) began increasing the outflow at Gavin’s Point, near Yankton, South Dakota in May. On June 14, 2011, the outflow reached a record rate of over 160,000 cubic feet per second (cfs), over twice the previous record outflow set in 1997. This increased output from Gavin’s Point caused the Missouri River to flow out of its banks covering over 283,000 acres of land in Iowa, forcing hundreds of evacuations, damaging 255,000 acres of cropland and significantly impacting the levee system on the Missouri River basin. Over the course of the summer, approximately 64 miles of primary roads closed due to Missouri River flooding, including 54 miles of Interstate Highway. Many county secondary roads were closed by high water or overburdened due to the numerous detours and road closures in this area. As the Missouri River levels began to increase, municipalities and counties aided by State and Federal agencies began preparing for a sustained flood event. Citizens, businesses, state agencies, local governments and non‐profits made substantial preparations, in some cases expending millions of dollars on emergency protective measures to protect their facilities from the impending flood. Levee monitors detected weak spots in the levee system in all affected counties, with several levees being identified as at risk levees that could potentially fail. Of particular concern was the 28 miles of levees protecting Council Bluffs. Based on this concern, Council Bluffs prepared an evacuation plan for the approximately 30,000 residents that resided in the protected area. On May 25, 2011, Governor Branstad directed the execution of the Iowa Emergency Response Plan in accordance with Section 401 of the Stafford Act. On May 31, 2011, HSEMD Administrator, Brigadier General J. Derek Hill, formally requested the USACE to provide technical assistance and advanced measures for the communities along the Missouri River basin. On June 2, 2011 Governor Branstad issued a State of Iowa Proclamation of Disaster Emergency for Fremont, Harrison, Mills, Monona, Pottawattamie, and Woodbury counties. The length of this flood event created a unique set of challenges for Federal, State and local entities. In many cases, these organizations were conducting response and recovery operations simultaneously. Due to the length of this entire event, the State Emergency Operations Center and the local Emergency Operations Centers remained open for an extended period of time, putting additional strain on many organizations and resources. In response to this disaster, Governor Branstad created the Missouri River Recovery Coordination Task Force to oversee the State’s recovery efforts. The Governor announced the creation of this Task Force on October 17, 2011 and appointed Brigadier General J. Derek Hill, HSEMD Administrator as the chairman. This Task Force would be a temporary group of State agency representatives and interested stakeholders brought together to support the recovery efforts of the Iowa communities impacted by the Missouri River Flood. Collectively, this group would analyze and share damage assessment data, coordinate assistance across various stakeholders, monitor progress, capture best practices and identify lessons learned.

Consumer Advisory Bulletin, Paper or Plastic? Gift Certificates & Gift Cards, February 2013

The Attorney General’s Consumer Protection Division receives hundreds of calls and consumer complaints every year. Follow these tips to avoid unexpected expense and disappointments. This record is about: Paper or Plastic? Gift Certificates & Gift Cards