Development of Preliminary Load and Resistance Factor Design of Drilled Shafts in Iowa, RB03-012, 2014

The Federal Highway Administration (FHWA) mandated utilizing the Load and Resistance Factor Design (LRFD) approach for all new bridges initiated in the United States after October 1, 2007. To achieve part of this goal, a database for Drilled Shaft Foundation Testing (DSHAFT) was developed and reported on by Garder, Ng, Sritharan, and Roling in 2012. DSHAFT is aimed at assimilating high-quality drilled shaft test data from Iowa and the surrounding regions. DSHAFT is currently housed on a project website (http://srg.cce.iastate.edu/dshaft) and contains data for 41 drilled shaft tests. The objective of this research was to utilize the DSHAFT database and develop a regional LRFD procedure for drilled shafts in Iowa with preliminary resistance factors using a probability-based reliability theory. This was done by examining current design and construction practices used by the Iowa Department of Transportation (DOT) as well as recommendations given in the American Association of State Highway and Transportation Officials (AASHTO) LRFD Bridge Design Specifications and the FHWA drilled shaft guidelines. Various analytical methods were used to estimate side resistance and end bearing of drilled shafts in clay, sand, intermediate geomaterial (IGM), and rock. Since most of the load test results obtained from O-cell do not pass the 1-in. top displacement criterion used by the Iowa DOT and the 5% of shaft diameter for top displacement criterion recommended by AASHTO, three improved procedures are proposed to generate and extend equivalent top load-displacement curves that enable the quantification of measured resistances corresponding to the displacement criteria. Using the estimated and measured resistances, regional resistance factors were calibrated following the AASHTO LRFD framework and adjusted to resolve any anomalies observed among the factors. To illustrate the potential and successful use of drilled shafts in Iowa, the design procedures of drilled shaft foundations were demonstrated and the advantages of drilled shafts over driven piles were addressed in two case studies.

Pile Design and Tests for Integral Abutment Bridges, HR-273, 1987

Expansion joints increase both the initial cost and the maintenance cost of bridges. Integral abutment bridges provide an attractive design alternative because expansion joints are eliminated from the bridge itself. However, the piles in these bridges are subjected to horizontal movement as the bridge expands and contracts during temperature changes. The objective of this research was to develop a method of designing piles for these conditions. Separate field tests simulating a pile and a bridge girder were conducted for three loading cases: (1) vertical load only, (2) horizontal displacement of pile head only, and (3) combined horizontal displacement of pile head with subsequent vertical load. Both tests (1) and (3) reached the same ultimate vertical load, that is, the horizontal displacement had no effect on the vertical load capacity. Several model tests were conducted in sand with a scale factor of about 1:10. Experimental results from both the field and model tests were used to develop the vertical and horizontal load-displacement properties of the soil. These properties were input into the finite element computer program Integral Abutment Bridge Two-Dimensional (IAB2D), which was developed under a previous research contract. Experimental and analytical results compared well for the test cases. Two alternative design methods, both based upon the American Association of State Highway and Transportation Officials (AASHTO) Specification, were developed. Alternative One is quite conservative relative to IAB2D results and does not permit plastic redistribution of forces. Alternative Two is also conservative when compared to IAB2D, but plastic redistribution is permitted. To use Alternative Two, the pile cross section must have sufficient inelastic rotation capacity before local buckling occurs. A design example for a friction pile and an end-bearing pile illustrates both alternatives.

Health in Iowa Annual Report: Behavioral Risk Factor Surveillance System, 2013

The Iowa Behavioral Risk Factor Surveillance System (BRFSS) is an ongoing telephone survey. It is financially and technically supported by the CDC with further financial support from public and private sources. The BRFSS is designed to collect information on the health conditions, health-related behaviors, attitudes, and awareness of residents age 18 and over. It also monitors the prevalence of these indicators over time. The indicators surveyed are major contributors to illness, disability, and premature death. This report focuses on the data collected during calendar year 2013. Some of the health-related issues discussed are general health status, health care access, cancer screening, tobacco use, alcohol consumption, body weight, physical activity, oral health, diabetes, respiratory conditions, immunizations, and HIV/AIDS awareness.

Health in Iowa Annual Report: Behavioral Risk Factor Surveillance System, 2014

The Iowa Behavioral Risk Factor Surveillance System (BRFSS) is an ongoing telephone survey. It is financially and technically supported by the CDC with further financial support from public and private sources. The BRFSS is designed to collect information on the health conditions, health-related behaviors, attitudes, and awareness of residents age 18 and over. It also monitors the prevalence of these indicators over time. The indicators surveyed are major contributors to illness, disability, and premature death. This report focuses on the data collected during calendar year 2013. Some of the health-related issues discussed are general health status, health care access, cancer screening, tobacco use, alcohol consumption, body weight, physical activity, oral health, diabetes, respiratory conditions, immunizations, and HIV/AIDS awareness.