Bentonite Treatment for Economical Dust Reduction on Limestone Surfaced Secondary Roads, HR-351, 1995

This research project was directed at laboratory and field evaluation of sodium montmorillonite clay (Bentonite) as a dust palliative for limestone surfaced secondary roads. It was postulated that the electrically charged surfaces (negative) of the clay particles could interact with the charged surfaces (positive) of the limestone and act as a bonding agent to agglomerate fine (-#200) particulates, and also to bond the fine particulates to larger (+#200) limestone particles. One mile test roads were constructed in Tama, Appanoose, and Hancock counties in Iowa using Bentonite treatment levels (by weight of aggregate) ranging from 3.0 to 12.0%. Construction was accomplished by adding dry Bentonite to the surfacing material and then dry road mixing. The soda ash/water solution (dispersing agent) was spray applied and the treated surfacing material wet mixed by motor graders to a consistency of 2 to 3 inch slump concrete. Two motor graders working in tandem provided rapid mixing. Following wet mixing the material was surface spread and compacted by local traffic. Quantitative and qualitative periodic evaluations and testing of the test roads was conducted with respect to dust generation, crust development, roughness, and braking characteristics. As the Bentonite treatment level increased dust generation decreased. From a cost/benefit standpoint, an optimum level of treatment is about 8% (by weight of aggregate). For roads with light traffic, one application at this treatment level resulted in a 60-70% average dust reduction in the first season, 40-50% in the second season, and 20-30% in the third season. Crust development was rated at two times better than untreated control sections. No discernible trend was evident with respect to roughness. There was no evident difference in any of the test sections with respect to braking distance and braking handling characteristics, under wet surface conditions compared to the control sections. Chloride treatments are more effective in dust reduction in the short term (3-4 months). Bentonite treatment is capable of dust reduction over the long term (2-3 seasons). Normal maintenance blading operations can be used on Bentonite treated areas. Soda ash dispersed Bentonite treatment is estimated to be more than twice as cost effective per percent dust reduction than conventional chloride treatments, with respect to time. However, the disadvantage is that there is not the initial dramatic reduction in dust generation as with the chloride treatment. Although dust is reduced significantly after treatment there is still dust being generated. Video evidence indicates that the dust cloud in the Bentonite treated sections does not rise as high, or spread as wide as the cloud in the untreated section. It also settles faster than the cloud in the untreated section. This is considered important for driving safety of following traffic, and for nuisance dust invasion of residences and residential areas. The Bentonite appears to be functioning as a bonding agent.

Reduction of Concrete Deterioration by Ettringite Using Crystal Growth Inhibition Techniques: Part II Field Evaluation of Inhibitor Effectiveness, TR-469, 2004

The effects of diethylenetriaminpenta(methylenephosphonic acid) (DTPMP), a phosphonate inhibitor, on the growth of delayed ettringite have been evaluated using concrete in highway US 20 near Williams, Iowa, and the cores of six highways subject to moderate (built in 1992) or minor (built in 1997) deterioration. Application of 0.01 and 0.1 vol. % DTPMP to cores was made on a weekly or monthly basis for one year under controlled laboratory-based freeze-thaw and wet-dry conditions over a temperature range of -15 degrees to 58 degrees C to mimic extremes in Iowa roadway conditions. The same concentrations of phosphonate were also applied to cores left outside (roof of Science I at Iowa State University) over the same period of time. Nineteen applications of 0.1 vol. % DTPMP with added deicing salt solution (about 23 weight % NACL) were made to US 20 during the winters of 2003 and 2004. In untreated samples, air voids, pores, and occasional cracks are lined with acicular ettringite crystals (up to 50 micrometers in length) whereas air voids, pores, and cracks in concrete from the westbound lane of US 20 are devoid of ettringite up to a depth of about 0.5 mm from the surface of the concrete. Ettringite is also absent in zones up to 6 mm from the surface of concrete slabs placed on the roof of Science I and cores subject to laboratory-based freeze-thaw experiments. In these zones, the relatively high concentration of DTPMP caused it to behave as a chelator. Stunted ettringite crystals 5 to 25 micrometers in length, occasionally coated with porlandite, form on the margins of these zones indicating that in these areas DTPMP behaved as an inhibitor due to a reduction in the concentration of phosphonate. Analyses of mixes of ettringite and DTPMP using electrospray mass spectrometry suggests that the stunting of ettringite growth is caused by the adsorption of a Ca2+ ion and a water molecule to deprotonated DTPMP on the surface of the {0001} face of ettringite. It is anticipated that by using a DTPMP concentration of between 0.001 and 0.01 vol. % for the extended life of a highway (i.e. >20 years), deterioration caused by the expansive growth of ettringite will be markedly reduced.

Feeding and the Equilibrium Feeder Animal Price-Weight Schedule, June 2005

The feeder animal price is a derivative in the sense that its value depends upon the price of animals for the consumption market. It also depends upon the biological growth technology and feed costs. Daily maintenance costs are of particular interest to the husbander because they can be avoided through accelerated feeding. In this paper, the optimal feeding path under equilibrium feeder animal prices is established. This analysis is used to gain a better understanding of feeding decisions, regulation in feedstuff markets, and the consequences of genetic innovations. It is shown that days on feed can increase or decrease with a genetic innovation or other improvement in feed conversion efficiency. The structure of comparative prices for feeder animals at different weights, the early slaughter decision, and equilibrium in feeder animal markets are also developed. Feeder animal prices can increase over a weight interval if biological feed efficiency parameters are low over the interval.

Pre-Treatment for Reduction of Asphalt Absorption in Porous Aggregate, April 2005

The objective of this research was to evaluate the performance of the product Ultracote® (a polymer based additive produced by Ultrapave, a division of Goodyear) as an aggregate pre-treatment for the reduction of asphalt binder absorption in hot mix asphalt (HMA). The product was tested with a paving project in Louisa county, Iowa with aggregate that had historically shown very high asphalt binder absorption. Results of the testing did not provide any evidence of reduction in binder absorption.

Healthy Iowans 2010 Mid-Course Revision, July 2005

In the past century, public health has been credited with adding 25 years to life expectancy by contributing to the decline in illness and injury. Progress has been made, for example, in smoking reduction, infectious disease, and motor vehicle and workplace injuries. Besides its focus on traditional concerns such as clean water and safe food, public health is adapting to meet emerging health problems. Particular troublesome are health threats to youth: teenage pregnancies, violence, substance abuse, sexually transmitted diseases, and other conditions associated with high-risk behaviors. These threats add to burgeoning health care costs. A conservative estimate of $69 billion in medical spending could be averted through the impact of public health strategies aimed at heart disease, stroke, fatal and nonfatal occupational injuries, motor vehicle-related injuries, low birth weight, and violence. These strategies require the collaboration of many groups in the public and private sectors. Collaboration is the bedrock of public health and Healthy Iowans planning. At the core of Healthy Iowans 2000 and its successor, Healthy Iowans 2010, is the idea that all Iowans benefit when stakeholders decide on disease prevention and health promotion strategies and agree to work together on them. These strategies can improve the quality of life and hold down health care costs. The payoff for health promotion and disease prevention is not immediate, but it has long-lasting benefits. The Iowa plan is a companion to the national plan, Healthy People 2010. An initiative to improve the health of Americans, the national plan is the driving force for federal resource allocation for disease prevention and health promotion. The state plan is used in the same way. Both plans have received broad support from Republican and Democratic administrations. Community planners are using the state plan to help assess health needs and craft health improvement plans. Healthy Iowans 2010 was written at an unusual point in history – a new decade, a new century, a new millennium. The introduction was optimistic. “The 21st century,” it says, “promises to add life as well as years through improved health habits coupled with medical advances. Scientists have suggested that if these changes occur, the definition of adulthood will also change. An extraordinary number of people will live fuller, more active lives beyond that expected in the late 20th century.” At the same time, the country has spawned a new generation of health hazards. According to Dr. William Dietz of the Centers for Disease Control and Prevention (CDC), it has replaced “the diseases of deficiency with diseases of excess” (Newsweek, August 2, 1999). New threats, such as childhood overweight, can reverse progress made in the last century. This demands concerted action.

Evaluation of U.S. and European Concrete Pavement Noise Reduction Methods, July 2006

Highway noise is one of the most pressing of the surface characteristics issues facing the concrete paving industry. This is particularly true in urban areas, where not only is there a higher population density near major thoroughfares, but also a greater volume of commuter traffic (Sandberg and Ejsmont 2002; van Keulen 2004). To help address this issue, the National Concrete Pavement Technology Center (CP Tech Center) at Iowa State University (ISU), Federal Highway Administration (FHWA), American Concrete Pavement Association (ACPA), and other organizations have partnered to conduct a multi-part, seven-year Concrete Pavement Surface Characteristics Project. This document contains the results of Part 1, Task 2, of the ISU-FHWA project, addressing the noise issue by evaluating conventional and innovative concrete pavement noise reduction methods. The first objective of this task was to determine what if any concrete surface textures currently constructed in the United States or Europe were considered quiet, had long-term friction characteristics, could be consistently built, and were cost effective. Any specifications of such concrete textures would be included in this report. The second objective was to determine whether any promising new concrete pavement surfaces to control tire-pavement noise and friction were in the development stage and, if so, what further research was necessary. The final objective was to identify measurement techniques used in the evaluation.

Waste Reduction, Construction and Demolition Debris: Guide for Building, Construction and Environmental Professionals, Revised November 2008

This document is intended to lay the foundation for resource reduction strategies in new construction, renovation and demolition. If you have an innovative idea or information that you believe should be included in future updates of this manual please email Shelly Codner at scodner@region12cog.org or Jan Loyson at Jan.Loyson@Iowalifechanging.com. Throughout this manual, we use the term “waste reduction” to define waste management initiatives that will result in less waste going to the landfill. In accordance with the waste management hierarchy these practices include reducing (waste prevention), reusing (deconstruction and salvage), recycling and renewing (making old things new again) - in that order. This manual will explain what these practices are and how to incorporate them into your projects.