Local Jurisdictions Information, 2003

Directory of county officials and employees

Telecommunications Competition Survey for Retail Local Voice Services in Iowa, January 26, 2004

Survey of retail local voice services for Iowa Utilities Board

Development of Abutment Design Standards for Local Bridge Designs, Volume 1 of 3, Development of Design Methodology, August 2004

Several superstructure design methodologies have been developed for low volume road bridges by the Iowa State University Bridge Engineering Center. However, to date no standard abutment designs have been developed. Thus, there was a need to establish an easy to use design methodology in addition to generating generic abutment standards and other design aids for the more common substructure systems used in Iowa. The final report for this project consists of three volumes. The first volume (this volume) summarizes the research completed in this project. A survey of the Iowa County Engineers was conducted from which it was determined that while most counties use similar types of abutments, only 17 percent use some type of standard abutment designs or plans. A literature review revealed several possible alternative abutment systems for future use on low volume road bridges in addition to two separate substructure lateral load analysis methods. These consisted of a linear and a non-linear method. The linear analysis method was used for this project due to its relative simplicity and the relative accuracy of the maximum pile moment when compared to values obtained from the more complex non-linear analysis method. The resulting design methodology was developed for single span stub abutments supported on steel or timber piles with a bridge span length ranging from 20 to 90 ft and roadway widths of 24 and 30 ft. However, other roadway widths can be designed using the foundation design template provided. The backwall height is limited to a range of 6 to 12 ft, and the soil type is classified as cohesive or cohesionless. The design methodology was developed using the guidelines specified by the American Association of State Highway Transportation Officials Standard Specifications, the Iowa Department of Transportation Bridge Design Manual, and the National Design Specifications for Wood Construction. The second volume introduces and outlines the use of the various design aids developed for this project. Charts for determining dead and live gravity loads based on the roadway width, span length, and superstructure type are provided. A foundation design template was developed in which the engineer can check a substructure design by inputting basic bridge site information. Tables published by the Iowa Department of Transportation that provide values for estimating pile friction and end bearing for different combinations of soils and pile types are also included. Generic standard abutment plans were developed for which the engineer can provide necessary bridge site information in the spaces provided. These tools enable engineers to design and detail county bridge substructures more efficiently. The third volume provides two sets of calculations that demonstrate the application of the substructure design methodology developed in this project. These calculations also verify the accuracy of the foundation design template. The printouts from the foundation design template are provided at the end of each example. Also several tables provide various foundation details for a pre-cast double tee superstructure with different combinations of soil type, backwall height, and pile type.

Development of Abutment Design Standards for Local Bridge Designs, Volume 3 of 3, Verification of Design Methodology, August 2004

Several superstructure design methodologies have been developed for low volume road bridges by the Iowa State University Bridge Engineering Center. However, to date no standard abutment designs have been developed. Thus, there was a need to establish an easy to use design methodology in addition to generating generic abutment standards and other design aids for the more common substructure systems used in Iowa. The final report for this project consists of three volumes. The first volume summarizes the research completed in this project. A survey of the Iowa County Engineers was conducted from which it was determined that while most counties use similar types of abutments, only 17 percent use some type of standard abutment designs or plans. A literature review revealed several possible alternative abutment systems for future use on low volume road bridges in addition to two separate substructure lateral load analysis methods. These consisted of a linear and a non-linear method. The linear analysis method was used for this project due to its relative simplicity and the relative accuracy of the maximum pile moment when compared to values obtained from the more complex non-linear analysis method. The resulting design methodology was developed for single span stub abutments supported on steel or timber piles with a bridge span length ranging from 20 to 90 ft and roadway widths of 24 and 30 ft. However, other roadway widths can be designed using the foundation design template provided. The backwall height is limited to a range of 6 to 12 ft, and the soil type is classified as cohesive or cohesionless. The design methodology was developed using the guidelines specified by the American Association of State Highway Transportation Officials Standard Specifications, the Iowa Department of Transportation Bridge Design Manual, and the National Design Specifications for Wood Construction. The second volume introduces and outlines the use of the various design aids developed for this project. Charts for determining dead and live gravity loads based on the roadway width, span length, and superstructure type are provided. A foundation design template was developed in which the engineer can check a substructure design by inputting basic bridge site information. Tables published by the Iowa Department of Transportation that provide values for estimating pile friction and end bearing for different combinations of soils and pile types are also included. Generic standard abutment plans were developed for which the engineer can provide necessary bridge site information in the spaces provided. These tools enable engineers to design and detail county bridge substructures more efficiently. The third volume (this volume) provides two sets of calculations that demonstrate the application of the substructure design methodology developed in this project. These calculations also verify the accuracy of the foundation design template. The printouts from the foundation design template are provided at the end of each example. Also several tables provide various foundation details for a pre-cast double tee superstructure with different combinations of soil type, backwall height, and pile type.

Development of Abutment Design Standards for Local Bridge Designs, Volume 2 of 3, Design Manual, August 2004

Several superstructure design methodologies have been developed for low volume road bridges by the Iowa State University Bridge Engineering Center. However, to date no standard abutment designs have been developed. Thus, there was a need to establish an easy to use design methodology in addition to generating generic abutment standards and other design aids for the more common substructure systems used in Iowa. The final report for this project consists of three volumes. The first volume summarizes the research completed in this project. A survey of the Iowa County Engineers was conducted from which it was determined that while most counties use similar types of abutments, only 17 percent use some type of standard abutment designs or plans. A literature review revealed several possible alternative abutment systems for future use on low volume road bridges in addition to two separate substructure lateral load analysis methods. These consisted of a linear and a non-linear method. The linear analysis method was used for this project due to its relative simplicity and the relative accuracy of the maximum pile moment when compared to values obtained from the more complex non-linear analysis method. The resulting design methodology was developed for single span stub abutments supported on steel or timber piles with a bridge span length ranging from 20 to 90 ft and roadway widths of 24 and 30 ft. However, other roadway widths can be designed using the foundation design template provided. The backwall height is limited to a range of 6 to 12 ft, and the soil type is classified as cohesive or cohesionless. The design methodology was developed using the guidelines specified by the American Association of State Highway Transportation Officials Standard Specifications, the Iowa Department of Transportation Bridge Design Manual, and the National Design Specifications for Wood Construction. The second volume (this volume) introduces and outlines the use of the various design aids developed for this project. Charts for determining dead and live gravity loads based on the roadway width, span length, and superstructure type are provided. A foundation design template was developed in which the engineer can check a substructure design by inputting basic bridge site information. Tables published by the Iowa Department of Transportation that provide values for estimating pile friction and end bearing for different combinations of soils and pile types are also included. Generic standard abutment plans were developed for which the engineer can provide necessary bridge site information in the spaces provided. These tools enable engineers to design and detail county bridge substructures more efficiently. The third volume provides two sets of calculations that demonstrate the application of the substructure design methodology developed in this project. These calculations also verify the accuracy of the foundation design template. The printouts from the foundation design template are provided at the end of each example. Also several tables provide various foundation details for a pre-cast double tee superstructure with different combinations of soil type, backwall height, and pile type.

Local Roads Maintenance Workers’ Manual, June 2006

This manual describes best roadway maintenance practices for Iowa's local roads and streets, from the center line to shoulders, ditches, and drainage, with chapters on public relations, bridge maintenance, and snow and ice control. Each chapter contains safety tips, information(as appropriate) on managing quality control, and a list of references for further information.

Iowa Adult Literacy Local Program Monitoring Guidelines Revised, July 2007

The purpose of this document is to provide guidelines for the annual monitoring and evaluation of Iowa’s adult literacy funded local programs. Section 224(b)(3) of the Adult Education and Family Literacy Act (AEFLA) states that the State Education Agency (SEA) will provide “a description of how the eligible agency [Iowa Department of Education] will evaluate annually the effectiveness of the adult education and literacy activities based on the performance measures described in section 212.” In compliance with that mandate, the following describes the Iowa Department of Education’s procedures for local adult literacy program evaluation strategies.

Report pursuant to House File 2782 (2007 Infrastructure Appropriations Act)

House File 2782 (2007 Infrastructure Appropriations Act) requires state agencies that receive Appropriations from specified funds to report that information. The Iowa Department of Transportation received funds from the Rebuild Iowa Infrastructure Fund, the State Recreational Trails Fund, Health Restricted Capitals, Rail Revolving Loan and Grant Program and the Tobacco settlement in FY 2008.

Annual Report of the Iowa Grape and Wine Development Commission for Fiscal Year, 2007

FY2007 was a productive year for the Iowa Grape and Wine Development Commission. Fourteen proposals were recommended for funding totaling over $390,000 in outlays. Included in the approved proposals were funds for the establishment and staffing of a Midwest Grape and Wine Institute at Iowa State University, a newly created viticulturist position at Des Moines Area Community College, funding for the first annual Mid-American Wine Competition, and marketing and promotion of four regional cooperative wine events and one wine trail. Commission funding supported a survey of commercial wine producers and grape growers and a new brochure on Iowa’s vineyards. A committee was formed to provide details for a Scholarship Program to aid vineyard and winery staff with the expenses of accredited coursework. Based on the survey conducted and from other governmental and industry sources, the Iowa grape and wine industry appears to continue to be very viable and growth continues at a strong pace. Wine produced in the state for 2007 was estimated at a market value in excess of $12.3 million. A tabulation of the budget revealed that just over $800,000 in wine gallonage tax appropriations have been received into the Grape and Wine Development Fund from 15 FY2003 through FY2007. Expenditures have totaled just over $607,000 during that same time. Just over 80% of expenditures have gone to “Technical” spending. Over time, funds invested in “Technical” programs will translate into an increasingly educated and institutionally-supported industry. Local, regional, and statewide events also appear to be increasing in popularity and the Commission plans to continue and increase support for these events. It is hoped the Scholarship Program will be up and running and funding will need to be appropriated for that project. The Commission also believes many projects and events will become more and more self sustaining as they develop and mature. As they continue to support Iowa’s grape and wine industry, the members of the Commission look forward to working with individuals, commercial enterprises, state and federal agencies, and industry-sponsored institutions in the upcoming year and in years to come.

Annual Report of the Iowa Grape and Wine Development Commission for Fiscal Year, 2008

FY2008 was a productive year for the Iowa Grape and Wine Development Commission. Sixteen proposals were recommended for funding from FY2008 funds and carryover totaling just over $396,000 in outlays. Included in the approved proposals were staffing and equipment for the Midwest Grape and Wine Industry Institute’s wine diagnostics laboratory at Iowa State University, continued support for the viticulturist position at Des Moines Area Community College, funding for the second annual Mid-American Wine Competition, and assistance for marketing and promotion of Ice coats an Iowa vineyard after a February 2008 ice storm. Photo by Mike White and courtesy of Iowa State University. 16 two wine trail associations and seven festivals and events. Commission funding supported a salaried position within IDALS to manage the Iowa Grape and Wine Development Fund and to serve as the Director of the Iowa Grape and Wine Development Commission. The Commission approved funding for a Scholarship Program. The formally created Scholarship Committee met twice in FY2008 to finalize details for the Program and to approve scholarships to twenty-six applicants to aid with the expenses of accredited coursework. Based on data collected by IDALS, the Iowa Department of Economic Development, the Iowa Alcoholic Beverages Division, and Iowa State University the Iowa grape and wine industry appears to continue to be very viable and growth continues at a strong pace. Presently, Iowa ranks 14th in the nation for the number of wineries, and wine produced in the state for 2008 was estimated at a market value in excess of $14.0 million. A tabulation of the budget revealed that just over $1,080,000 in wine gallonage tax appropriations and legislative appropriations have been deposited into the Grape and Wine Development Fund from FY2003 through FY2008. Removing encumbered funds, expenditures have totaled just over $942,500 during that same time. “Financial” funding – used for fostering public awareness and participation of industry events - increased from 6% of expenditures in FY2007 to 9% in FY2008. Used for support of research, education, and outreach, a little over 80% of expenditures and encumbered funds were earmarked for “Technical” spending. Over time, funds invested in “Technical” programs will translate into an increasingly educated and institutionally-supported industry. Local, regional, and statewide events also appeared to be increasing in popularity. The Commission was encouraged to see increased support for these events. It is hoped, too, that the Scholarship Program will provide needed funding to help meet the educational goals of the industry’s workforce. As they continue to support Iowa’s grape and wine industry, the Commissioners look forward to working with individuals, commercial enterprises, state and federal agencies, and industry-sponsored institutions in FY2009 and in years to come.

2009-2011 Collective Bargaining Agreement Between State of Iowa and Local 893; Science Unit, July 1, 2009

This Agreement made and entered i into this 1 1st day of July 2009, at Des Moines, Iowa, pursuant to the provisions of Chapter 20 of the Iowa Code, by and between the State of Iowa (hereinafter referred to as the Employer) and UE Local 893/Iowa United Professionals, and its appropriate affiliated locals, as representatives of employees employed by the State of Iowa, as set forth specifically in Appendix A (hereinafter referred to as the Union).

2009-2011 Collective Bargaining Agreement Between State of Iowa and Local 893; Social Services, July 1, 2009

This Agreement made and entered i into this 1 1st day of July 2009, at Des Moines, Iowa, pursuant to the provisions of Chapter 20 of the Iowa Code, by and between the State of Iowa (hereinafter referred to as the Employer) and UE Local 893/Iowa United Professionals, and its appropriate affiliated locals, as representatives of employees employed by the State of Iowa.

Report on the Local Public Health Services Grant administered by the Bureau of Local Public Health Services, a division of Health Promotion and Chronic Disease Prevention of the Iowa Department of Public Health for the period July 1, 2006 through June 30, 2008

Report on the Local Public Health Services Grant administered by the Bureau of Local Public Health Services, a division of Health Promotion and Chronic Disease Prevention of the Iowa Department of Public Health for the period July 1, 2006 through June 30, 2008

Local Jurisdictions Information, 2010

Directory of county officials and employees

Local Letting Information, April 4, 2011

Local letting information