Investigation of Two Bridge Alternatives for Low Volume Roads Volume 2 of 2 Concept 2: Beam In Slab Bridge, HR-382, 1997

Recent reports have indicated that 23.5% of the nation's highway bridges are structurally deficient and 17.7% are functionally obsolete. A significant number of these bridges are on the Iowa secondary road system where over 86% of the rural bridge management responsibilities are assigned to the counties. Some of the bridges can be strengthened or otherwise rehabilitated, but many more are in need of immediate replacement. In a recent investigation (HR-365 "Evaluation of Bridge Replacement Alternatives for the County Bridge System") several types of replacement bridges that are currently being used on low volume roads were identified. It was also determined that a large number of counties (69%) have the ability and are interested in utilizing their own forces to design and construct short span bridges. After reviewing the results from HR-365, the research team developed one "new" bridge replacement concept and a modification of a replacement system currently being used. Both of these bridge replacement alternatives were investigated in this study, the results of which are presented in two volumes. This volume (Volume 2) presents the results of Concept 2 - Modification of the Beam-in-Slab Bridge. Concept 1 - Steel Beam Precast Units is presented in Volume 1. Concept 2 involves various laboratory tests of the Beam-in-Slab bridge (BISB) currently being used by Benton County and several other Iowa counties. In this investigation, the behavior and strength of the BISB were determined; a new method of obtaining composite action between the steel beams and concrete was also tested. Since the Concept 2 bridge is primarily intended for use on low-volume roads, the system can be constructed with new or used beams. In the experimental part of the investigation, there were three types of laboratory tests: push-out tests, service and ultimate load tests of models of the BISB, and composite beam tests utilizing the newly developed shear connection. In addition to the laboratory tests, there was a field test in which an existing BISB was service load tested. An equation was developed for predicting the strength of the shear connection investigated; in addition, a finite element model for analyzing the BISB was also developed. Push-out tests were completed to determine the strength of the recently developed shear connector. A total of 36 specimens were tested, with variables such as hole diameter, hole spacing, presence of reinforcement, etc. being investigated. In the model tests of the BISB, two and four beam specimens [L=9,140 mm (30 ft)] were service load tested for behavior and load distribution data. Upon completion of these tests, both specimens were loaded to failure. In the composite beam tests, four beams, one with standard shear studs and three using the shear connection developed, were tested. Upon completion of the service load tests, all four beams were loaded to failure. The strength and behavior of the beams with the new shear connection were found to be essentially the same as that of the specimen with standard shear studs.

Investigation of Two Bridge Alternatives for Low Volume Roads - Phase II Volume 2 of 2, Concept 2: Beam in Slab Bridge, TR-410, 2000

This project continues the research which addresses the numerous bridge problems on the Iowa secondary road system. It is a continuation (Phase 2) of Project HR-382, in which two replacement alternatives (Concept 1: Steel Beam Precast Units and Concept 2: Modification of the Benton County Beam-in-Slab Bridge) were investigated. In previous research for concept 1, a precast unit bridge was developed through laboratory testing. The steel-beam precast unit bridge requires the fabrication of precast double-tee (PCDT) units, each consisting of two steel beams connected by a reinforced concrete deck. The weight of each PCDT unit is minimized by limiting the deck thickness to 4 in., which permits the units to be constructed off-site and then transported to the bridge site. The number of units required is a function of the width of bridge desired. Once the PCDT units are connected, a cast-in-place reinforced concrete deck is cast over the PCDT units and the bridge railing attached. Since the steel beam PCDT unit bridge design is intended primarily for use on low-volume roads, used steel beams can be utilized for a significant cost savings. In previous research for concept 2, an alternate shear connector (ASC) was developed and subjected to static loading. In this investigation, the ASC was subjected to cyclic loading in both pushout specimens and composite beam tests. Based on these tests, the fatigue strength of the ASC was determined to be significantly greater than that required in typical low volume road single span bridges. Based upon the construction and service load testing, the steel-beam precast unit bridge was successfully shown to be a viable low volume road bridge alternative. The construction process utilized standard methods resulting in a simple system that can be completed with a limited staff. Results from the service load tests indicated adequate strength for all legal loads. An inspection of the bridge one year after its construction revealed no change in the bridge's performance. Each of the systems previously described are relatively easy to construct. Use of the ASC rather than the welded studs significantly simplified the work, equipment, and materials required to develop composite action between the steel beams and the concrete deck.

Iowa Uniform Crime Report, Iowa Department of Public Safety, 1997

In 1974, the 65th Iowa General Assembly enacted a provision of Chapter 749 B of the Code of Iowa requiring law enforcement agencies to submit reports of crime and arrests to the Bureau of Criminal Investigation. The following language now is contained in section 692.15 Code of Iowa concerning Uniform Crime Reports: If it comes to the attention of a sheriff, police department or other law enforcement agency that a public offense has been committed in its jurisdiction, the law enforcement agency shall report information concerning such a public offense to the department on a form to be furnished by the department not more than thirty-five days from the time the public offense first comes to the attention of the law enforcement agency. The reports shall be used to generate crime statistics. The department shall submit statistics to the governor, the general assembly, and the division of criminal and juvenile justice planning of the department of human rights on a quarterly and yearly basis.

Investigation into the Transitioning of Reggis Kelsey out of Iowa's Foster Care System, 2003

Investigative report produced by Iowa Citizens' Aide/Ombudsman

Iowa Department of Public Safety 2005 Annual Report

The Iowa Department of Public Safety (DPS) has a history of dedication and service to the citizens of Iowa and those who visit our state. Since it was first established in 1939, DPS has been the chief law enforcement agency in the State of Iowa. DPS is headquartered in Des Moines, Iowa in the Wallace State Office Building on the Capitol Complex, along with a statewide presence.

Iowa Department of Public Safety 2006 Annual Report

The Iowa Department of Public Safety (DPS) has a history of dedication and service to the citizens of Iowa and those who visit our state. Since it was first established in 1939, DPS has been the chief law enforcement agency in the State of Iowa. DPS is headquartered in Des Moines, Iowa in the Wallace State Office Building on the Capitol Complex, along with a statewide presence.

Iowa Department of Public Safety 2007 Annual Report

The Iowa Department of Public Safety (DPS) has a history of dedication and service to the citizens of Iowa and those who visit our state. Since it was first established in 1939, DPS has been the chief law enforcement agency in the State of Iowa. DPS is headquartered in Des Moines, Iowa in the Wallace State Office Building on the Capitol Complex, along with a statewide presence.

Iowa Department of Public Safety 2008 Annual Report

The Iowa Department of Public Safety (DPS) has a history of dedication and service to the citizens of Iowa and those who visit our state. Since it was first established in 1939, DPS has been the chief law enforcement agency in the State of Iowa. DPS is headquartered in Des Moines, Iowa in the Wallace State Office Building on the Capitol Complex, along with a statewide presence.

Iowa Department of Public Safety: Iowa State Patrol, 2008 Annual Report

As Iowa's traffic enforcement agency, the Iowa State Patrol is responsible for providing law enforcement services to rural areas of the state as well as traffic enforcement and support for metropolitan areas around the state. Troopers patrol Iowa's highways and conduct traffic enforcement for both unincorporated areas and interstate highways. In addition, our Personnel provide security and police services throughout the state for many special events including, fairs, festivals, and large sporting events such as the Iowa Speedway, University of Iowa and Iowa State football games.

Investigation of Two Bridge Alternatives for Low Volume Roads - Phase II Volume 1 of 2 Concept 1: Steel Beam Precast Units, TR-410, 2000

This project continues the research which addresses the numerous bridge problems on the Iowa secondary road system. It is a continuation (Phase 2) of Project HR-382, in which two replacement alternatives (Concept 1: Steel Beam Precast Units and Concept 2: Modification of the Benton County Beam-in-Slab Bridge) were investigated. In previous research for concept 1, a precast unit bridge was developed through laboratory testing. The steel-beam precast unit bridge requires the fabrication of precast double-tee (PCDT) units, each consisting of two steel beams connected by a reinforced concrete deck. The weight of each PCDT unit is minimized by limiting the deck thickness to 4 in., which permits the units to be constructed off-site and then transported to the bridge site. The number of units required is a function of the width of bridge desired. Once the PCDT units are connected, a cast-in-place reinforced concrete deck is cast over the PCDT units and the bridge railing attached. Since the steel beam PCDT unit bridge design is intended primarily for use on low-volume roads, used steel beams can be utilized for a significant cost savings. In previous research for concept 2, an alternate shear connector (ASC) was developed and subjected to static loading. In this investigation, the ASC was subjected to cyclic loading in both pushout specimens and composite beam tests. Based on these tests, the fatigue strength of the ASC was determined to be significantly greater than that required in typical low volume road single span bridges. Based upon the construction and service load testing, the steel-beam precast unit bridge was successfully shown to be a viable low volume road bridge alternative. The construction process utilized standard methods resulting in a simple system that can be completed with a limited staff. Results from the service load tests indicated adequate strength for all legal loads. An inspection of the bridge one year after its construction revealed no change in the bridge's performance. Each of the systems previously described are relatively easy to construct. Use of the ASC rather than the welded studs significantly simplified the work, equipment, and materials required to develop composite action between the steel beams and the concrete deck.

DCI Voter Fraud Investigations Report, May 8, 2014.

In March of 2012, the Iowa Secretary of State’s office compared Iowa’s voter registration records with the driver’s license record s of individuals that identified themselves as non-citizens with the Iowa Department of Transportation. After comparing those records, the Iowa Secretary of State’s office found that more than 3,000 individuals registered to vote that had previously identified themselves as non-citizens. More than 1,000 of these individuals had also cast a ballot. The Iowa Secretary of State’s office was not given timely access to the federal Systematic Alien Verification for Entitlements (SAVE)database, and therefore was unable to determine if any of these individuals had become citizens before they registered to vote or cast a ballot. On June 21, 2012, the Iowa Secretary of State’s office entered into an agreement with the Iowa Department of Public Safety’s Division of Criminal Investigation (DCI) to review potential election misconduct crimes and improve the administration of federal elections. Over the last two years,DCI agents have reviewed thousands of instances of possible election misconduct. DCI’s review included cases referred by the Iowa Secretary of State’s office as well as by other state and local government agencies.

Law enforcement opportunities for minorities,2009

This brochure gives information about the Iowa Department of Public Safety and describes available career opportunities in the department.

Nonlinear Pile Behavior in Integral Abutment Bridges, HR-227, Part 1, 1982

The highway departments of all fifty states were contacted to find the extent of application of integral abutment bridges, to survey the different guidelines used for analysis and design of integral abutment bridges, and to assess the performance of such bridges through the years. The variation in design assumptions and length limitations among the various states in their approach to the use of integral abutments is discussed. The problems associated with lateral displacements at the abutment, and the solutions developed by the different states for most of the ill effects of abutment movements are summarized in the report. An algorithm based on a state-of-the-art nonlinear finite element procedure was developed and used to study piling stresses and pile-soil interaction in integral abutment bridges. The finite element idealization consists of beam-column elements with geometric and material nonlinearities for the pile and nonlinear springs for the soil. An idealized soil model (modified Ramberg-Osgood model) was introduced in this investigation to obtain the tangent stiffness of the nonlinear spring elements. Several numerical examples are presented in order to establish the reliability of the finite element model and the computer software developed. Three problems with analytical solutions were first solved and compared with theoretical solutions. A 40 ft H pile (HP 10 X 42) in six typical Iowa soils was then analyzed by first applying a horizontal displacement (to simulate bridge motion) and no rotation at the top and then applying a vertical load V incrementally until failure occurred. Based on the numerical results, the failure mechanisms were generalized to be of two types: (a) lateral type failure and (b) vertical type failure. It appears that most piles in Iowa soils (sand, soft clay and stiff clay) failed when the applied vertical load reached the ultimate soil frictional resistance (vertical type failure). In very stiff clays, however, the lateral type failure occurs before vertical type failure because the soil is sufficiently stiff to force a plastic hinge to form in the pile as the specified lateral displacement is applied. Preliminary results from this investigation showed that the vertical load-carrying capacity of H piles is not significantly affected by lateral displacements of 2 inches in soft clay, stiff clay, loose sand, medium sand and dense sand. However, in very stiff clay (average blow count of 50 from standard penetration tests), it was found that the vertical load carrying capacity of the H pile is reduced by about 50 percent for 2 inches of lateral displacement and by about 20 percent for lateral displacement of 1 inch. On the basis of the preliminary results of this investigation, the 265-feet length limitation in Iowa for integral abutment concrete bridges appears to be very conservative.

Nonlinear Finite Element Study of Piles in Integral Abutment Bridges, HR-227, Part 2, 1982

The highway departments of the states which use integral abutments in bridge design were contacted in order to study the extent of integral abutment use in skewed bridges and to survey the different guidelines used for analysis and design of integral abutments in skewed bridges. The variation in design assumptions and pile orientations among the various states in their approach to the use of integral abutments on skewed bridges is discussed. The problems associated with the treatment of the approach slab, backfill, and pile cap, and the reason for using different pile orientations are summarized in the report. An algorithm based on a state-of-the-art nonlinear finite element procedure previously developed by the authors was modified and used to study the influence of different factors on behavior of piles in integral abutment bridges. An idealized integral abutment was introduced by assuming that the pile is rigidly cast into the pile cap and that the approach slab offers no resistance to lateral thermal expansion. Passive soil and shear resistance of the cap are neglected in design. A 40-foot H pile (HP 10 X 42) in six typical Iowa soils was analyzed for fully restrained pile head and pinned pile head. According to numerical results, the maximum safe length for fully restrained pile head is one-half the maximum safe length for pinned pile head. If the pile head is partially restrained, the maximum safe length will lie between the two limits. The numerical results from an investigation of the effect of predrilled oversized holes indicate that if the length of the predrilled oversized hole is at least 4 feet below the ground, the vertical load-carrying capacity of the H pile is only reduced by 10 percent for 4 inches of lateral displacement in very stiff clay. With no predrilled oversized hole, the pile failed before the 4-inch lateral displacement was reached. Thus, the maximum safe lengths for integral abutment bridges may be increased by predrilling. Four different typical Iowa layered soils were selected and used in this investigation. In certain situations, compacted soil (> 50 blow count in standard penetration tests) is used as fill on top of natural soil. The numerical results showed that the critical conditions will depend on the length of the compacted soil. If the length of the compacted soil exceeds 4 feet, the failure mechanism for the pile is similar to one in a layer of very stiff clay. That is, the vertical load-carrying capacity of the H pile will be greatly reduced as the specified lateral displacement increases.

Iowa Department of Public Safety Annual Report, FY2013

The Iowa Department of Public Safety (DPS) has a history of dedication and service to the citizens of Iowa and those who visit our state. Since it was first established in 1939, DPS has been the chief law enforcement agency in the State of Iowa. DPS is headquartered in Des Moines, Iowa in the Wallace State Office Building on the Capitol Complex, along with a statewide presence.