Code Section 307.46(2) - Use of Reversions Report, Iowa Department of Transportation, 2003

Use of Reversions Report

Dowel Bar Optimization: Phases I and II, October 2001

America’s roadways are in serious need of repair. According to the American Society of Civil Engineers (ASCE), one-third of the nation’s roads are in poor or mediocre condition. ASCE has estimated that under these circumstances American drivers will sacrifice $5.8 billion and as many as 13,800 fatalities a year from 1999 to 2001 ( 1). A large factor in the deterioration of these roads is a result of how well the steel reinforcement transfers loads across the concrete slabs. Fabricating this reinforcement using a shape conducive to transferring these loads will help to aid in minimizing roadway damage. Load transfer within a series of concrete slabs takes place across the joints. For a typical concrete paved road, these joints are approximately 1/8-inch gaps between two adjacent slabs. Dowel bars are located at these joints and used to transfer load from one slab to its adjacent slabs. As long as the dowel bar is completely surrounded by concrete no problems will occur. However, when the hole starts to oblong a void space is created and difficulties can arise. This void space is formed due to a stress concentration where the dowel contacts the concrete. Over time, the repeated process of traffic traveling over the joint crushes the concrete surrounding the dowel bar and causes a void in the concrete. This void inhibits the dowel’s ability to effectively transfer load across the joint. Furthermore, this void gives water and other particles a place to collect that will eventually corrode and potentially bind or lock the joint so that no thermal expansion is allowed. Once there is no longer load transferred across the joint, the load is transferred to the foundation and differential settlement of the adjacent slabs will occur.

Assessment of Dowel Bar Research, August 2002

This report presents the latest technological gaps in dowel bar research based upon completed and ongoing dowel bar research from across the nation. In order to obtain this collection of information about dowel bars, a search was conducted on a nationwide level. The technological gaps and duplications of the research were then determined. In addition, this report also provides a brief annotated bibliography of all sources used to determine the gaps in technology and knowledge for dowel bar and alternative dowel bar topics as applied to highway pavements.

Dowel Bar Optimization: Phases I and II, October 2001

America’s roadways are in serious need of repair. According to the American Society of Civil Engineers (ASCE), one-third of the nation’s roads are in poor or mediocre condition (1). ASCE has estimated that under these circumstances American drivers will sacrifice $5.8 billion and as many as 13,800 fatalities a year from 1999 to 2001 ( 1). A large factor in the deterioration of these roads is a result of how well the steel reinforcement transfers loads across the concrete slabs. Fabricating this reinforcement using a shape conducive to transferring these loads will help to aid in minimizing roadway damage. Load transfer within a series of concrete slabs takes place across the joints. For a typical concrete paved road, these joints are approximately 1/8-inch gaps between two adjacent slabs. Dowel bars are located at these joints and used to transfer load from one slab to its adjacent slabs. As long as the dowel bar is completely surrounded by concrete no problems will occur. However, when the hole starts to oblong a void space is created and difficulties can arise. This void space is formed due to a stress concentration where the dowel contacts the concrete. Over time, the repeated process of traffic traveling over the joint crushes the concrete surrounding the dowel bar and causes a void in the concrete. This void inhibits the dowel’s ability to effectively transfer load across the joint. Furthermore, this void gives water and other particles a place to collect that will eventually corrode and potentially bind or lock the joint so that no thermal expansion is allowed. Once there is no longer load transferred across the joint, the load is transferred to the foundation and differential settlement of the adjacent slabs will occur.

Report on applying agreed-upon procedures to the City of Protivin’s certification of compliance with Chapter 388.10 of the Code of Iowa

Report on applying agreed-upon procedures to the City of Protivin’s certification of compliance with Chapter 388.10 of the Code of Iowa

Report on applying agreed-upon procedures to the City of Protivin’s certification of compliance with Chapter 388.10 of the Code of Iowa for the year ended June 30, 2008

Report on applying agreed-upon procedures to the City of Protivin’s certification of compliance with Chapter 388.10 of the Code of Iowa for the year ended June 30, 2008

Report on applying agreed-upon procedures to the City of Protivin’s certification of compliance with Chapter 388.10 of the Code of Iowa for the year ended June 30, 2007

Report on applying agreed-upon procedures to the City of Protivin’s certification of compliance with Chapter 388.10 of the Code of Iowa for the year ended June 30, 2007

Iowa Department of Transportation Fiscal Year 2008 Report of Savings by Using Video Conferencing Through Iowa Communications Network to the Iowa General Assembly Pursuant to Iowa Code § II 84 Acts and Joint Resolutions Enacted at the 1994 Regular Session of the 75th General Assembly of the State of Iowa Iowa Code §8D.10 Report of Savings by State Agencies

Iowa Code § 8D.10 requires certain state agencies prepare an annual report to the General Assembly certifying the identified savings associated with that state agency’s use of the Iowa Communications Network (ICN). This report covers estimated cost savings related to video conferencing via ICN for the Iowa Department of Transportation (DOT). In FY 2008, the DOT did not conduct any sessions utilizing ICN’s video conferencing system. Therefore, no cost savings were calculated for this report.

Construction Code, November 25, 2008

Construction codes establish minimum standards for structural integrity, life safety, accessibility and energy conservation in construction of buildings and facilities intended for human occupancy. These requirements affect all of the major systems of buildings and facilities.

Equipment and Vehicle Purchase Report for Fiscal Year 2009 as required by Iowa Code section 307.47

Attached is the Equipment and Vehicle Purchase Report for Fiscal Year 2009 as required by Iowa Code section 307.47. The report is sorted by Iowa Department of Transportation accounting object codes.

Letter to the Colo-Nesco Community School District as a result of reaudit procedures performed at the request of the Superintendent pursuant to Chapter 11.6(4)(a)(2) of the Code of Iowa for the period July 1, 2007 through June 30, 2008

Letter to the Colo-Nesco Community School District as a result of reaudit procedures performed at the request of the Superintendent pursuant to Chapter 11.6(4)(a)(2) of the Code of Iowa for the period July 1, 2007 through June 30, 2008

Iowa Department of Transportation Fiscal Year 2010 Report of Savings by Using Video Conferencing Through Iowa Communications Network to the Iowa General Assembly Pursuant to Iowa Code § II 84 Acts and Joint Resolutions Enacted at the 1994 Regular Session of the 75th General Assembly of the State of Iowa

Introduction and summary Iowa Code § 8D.10 requires certain state agencies to prepare an annual report to the General Assembly certifying the identified savings associated with that state agency’s use of the Iowa Communications Network (ICN). This report covers estimated cost savings related to video conferencing via ICN for the Iowa Department of Transportation (DOT). In FY 2010, the DOT did not conduct any sessions utilizing ICN’s video conferencing system. Therefore, no cost savings were calculated for this report.

Iowa Code Section 307.47 Equipment and Vehicle Report

Attached is the Iowa Department of Transportation's Equipment and Vehicle Purchase Report for Fiscal Year 2010 as required by Iowa Code section 307.47.

Iowa "50 States Project": A Review of the 1983 Code for Sexuality Discrimination, February 1984

The "50 States Project" is the name given to President Ronald D. Reagan;s 1981 pledge to encourage the fifty governors to initiate individual state projects to review their state Codes for unequal treatment of persons based upon sex. We believe that Iowa is the first state to complete this project. Project efforts in Iowa began in June of 1981, when the Governor Robert D. ray appointed Dr. Patricia L. Geadelmann, Chairperson on the Iowa commission on the Status of Women, as Iowa's 50 State Project representative. A 50 States planning committee was formed consisting of members from the Governor Ray's staff, the Iowa Commission on the Status of Women, and the Iowa Legislature. Various alternatives for reviewing the Iowa code and the Iowa Administrative Rules were studied and recommendations of the group were reported to Governor Terry E. Branstad prior to his inauguration.

Code Section 307.46(2) - Use of Reversion Report

Pursuant to Iowa Code Section 307.46(2), I submit the following report on the use of reversions. The Iowa Department of Transportation spent $498,703 of the Fiscal Year 2010 Road Use Tax Fund/Primary Road Fund budget reversion in Fiscal Year 2011 for desktop, server and network software, information technology professional services and computer equipment.