Apical access and closure devices for transapical transcatheter heart valve procedures.

The majority of transcatheter aortic valve implantations, structural heart procedures and the newly developed transcatheter mitral valve repair and replacement are traditionally performed either through a transfemoral or a transapical access site, depending on the presence of severe peripheral vascular disease or anatomic limitations. The transapical approach, which carries specific advantages related to its antegrade nature and the short distance between the introduction site and the cardiac target, is traditionally performed through a left anterolateral mini-thoracotomy and requires rib retractors, soft tissue retractors and reinforced apical sutures to secure, at first, the left ventricular apex for the introduction of the stent-valve delivery systems and then to seal the access site at the end of the procedure. However, despite the advent of low-profile apical sheaths and newly designed delivery systems, the apical approach represents a challenge for the surgeon, as it has the risk of apical tear, life-threatening apical bleeding, myocardial damage, coronary damage and infections. Last but not least, the use of large-calibre stent-valve delivery systems and devices through standard mini-thoracotomies compromises any attempt to perform transapical transcatheter structural heart procedures entirely percutaneously, as happens with the transfemoral access site, or via a thoracoscopic or a miniaturised video-assisted percutaneous technique. During the past few years, prototypes of apical access and closure devices for transapical heart valve procedures have been developed and tested to make this standardised successful procedure easier. Some of them represent an important step towards the development of truly percutaneous transcatheter transapical heart valve procedures in the clinical setting.

Simultaneous cell morphometry and refractive index measurement with dual-wavelength digital holographic microscopy and dye-enhanced dispersion of perfusion medium.

Digital holographic microscopy (DHM) allows optical-path-difference (OPD) measurements with nanometric accuracy. OPD induced by transparent cells depends on both the refractive index (RI) of cells and their morphology. This Letter presents a dual-wavelength DHM that allows us to separately measure both the RI and the cellular thickness by exploiting an enhanced dispersion of the perfusion medium achieved by the utilization of an extracellular dye. The two wavelengths are chosen in the vicinity of the absorption peak of the dye, where the absorption is accompanied by a significant variation of the RI as a function of the wavelength.

Red blood cell structure and dynamics explored with digital holographic microspcopy

Digital holographic microscopy (DHM) is a technique that allows obtaining, from a single recorded hologram, quantitative phase image of living cell with interferometric accuracy. Specifically the optical phase shift induced by the specimen on the transmitted wave front can be regarded as a powerful endogenous contrast agent, depending on both the thickness and the refractive index of the sample. Thanks to a decoupling procedure cell thickness and intracellular refractive index can be measured separately. Consequently, Mean corpuscular volume (MCV) and mean corpuscular hemoglobin concentration (MCHC), two highly relevant clinical parameters, have been measured non-invasively at a single cell level. The DHM nanometric axial and microsecond temporal sensitivities have permitted to measure the red blood cell membrane fluctuations (CMF) on the whole cell surface. ©2009 COPYRIGHT SPIE--The International Society for Optical Engineering.

Physicochemical aspects and efficiency of albuterol nebulization: comparison of three aerosol types in an in vitro pediatric model.

BACKGROUND: Advances in nebulizer design have produced both ultrasonic nebulizers and devices based on a vibrating mesh (vibrating mesh nebulizers), which are expected to enhance the efficiency of aerosol drug therapy. The aim of this study was to compare 4 different nebulizers, of 3 different types, in an in vitro model using albuterol delivery and physical characteristics as benchmarks. METHODS: The following nebulizers were tested: Sidestream Disposable jet nebulizer, Multisonic Infra Control ultrasonic nebulizer, and the Aerogen Pro and Aerogen Solo vibrating mesh nebulizers. Aerosol duration, temperature, and drug solution osmolality were measured during nebulization. Albuterol delivery was measured by a high-performance liquid chromatography system with fluorometric detection. The droplet size distribution was analyzed with a laser granulometer. RESULTS: The ultrasonic nebulizer was the fastest device based on the duration of nebulization; the jet nebulizer was the slowest. Solution temperature decreased during nebulization when the jet nebulizer and vibrating mesh nebulizers were used, but it increased with the ultrasonic nebulizer. Osmolality was stable during nebulization with the vibrating mesh nebulizers, but increased with the jet nebulizer and ultrasonic nebulizer, indicating solvent evaporation. Albuterol delivery was 1.6 and 2.3 times higher with the ultrasonic nebulizer and vibrating mesh nebulizers devices, respectively, than with the jet nebulizer. Particle size was significantly higher with the ultrasonic nebulizer. CONCLUSIONS: The in vitro model was effective for comparing nebulizer types, demonstrating important differences between nebulizer types. The new devices, both the ultrasonic nebulizers and vibrating mesh nebulizers, delivered more aerosolized drug than traditional jet nebulizers.

Non-invasive dry mass determination and monitoring at the single cell level with digital holographic microscopy

Digital holography microscopy (DHM) is an optical microscopy technique which allows recording non-invasively the phase shift induced by living cells with nanometric sensitivity. Here, we exploit the phase signal as an indicator of dry mass (related to the protein concentration). This parameter allows monitoring the protein production rate and its evolution during the cell cycle. ©2008 COPYRIGHT SPIE

Cutaneous benign mixed tumor (chondroid syringoma) of the eyelid: clinical presentation and management.

PURPOSE: To describe the clinical presentation of cutaneous benign mixed tumor of the eyelid and its management options. METHODS: Periocular cases of cutaneous benign mixed tumor were gathered from members of an oculoplastics specialty Internet discussion group. A total of 9 patients are described in this retrospective, interventional case series. The clinical presentation, histopathology, and management of these lesions is reviewed. RESULTS: Patients were typically asymptomatic, presenting with a slowly enlarging, nontender nodule of 2 to 8 years' duration. The lesions ranged from 4 mm to 17 mm in greatest dimension. Four of the lesions were on the eyelid margin, three in the sub-brow area of the upper eyelid, and two in the central lids. All six cases not involving the brow were fixed to the tarsus; one brow lesion was believed to be adherent to the skin. None of the lesions was associated with significant changes of the overlying epidermis, although one lesion showed overlying pigmentation. All patients underwent excisional biopsy for diagnostic or cosmetic reasons. On histopathologic examination, the tumors were biphasic, with an epithelial component exhibiting apocrine or hair follicle differentiation and a myxoid, adipocytic, chondroid, and/or fibrous stroma. The pathologic diagnoses were all consistent with cutaneous benign mixed tumor (chondroid syringoma, pleomorphic adenoma). Follow-up ranged from 2 weeks to 12 months, although several patients failed to keep scheduled follow-up appointments. No clinical recurrences were identified. CONCLUSIONS: Cutaneous benign mixed tumor may occur in the eyelid, and, although uncommon, should be included in the differential diagnosis of firm, nodular eyelid tumors. The histopathologic features are similar to those seen in this tumor type arising in other areas of the body. Preoperative consideration of this diagnostic possibility may allow the surgeon to plan for complete excision, thereby reducing the possibility of recurrence or malignant transformation.

Membrane insertion and antibody recognition of a glycosylphosphatidylinositol-anchored protein: an optical study.

The kinetics of binding of a glycolipid-anchored protein (the promastigote surface protease, PSP) to planar lecithin bilayers is studied by an integrated optics technique, in which the bilayer membrane is supported on an optical wave guide and the phase velocities of guided light modes in the wave guide are measured. From these velocities, the optical parameters of the membrane and PSP layers deposited on the waveguide are determined, yielding in particular the mass of PSP bound to the membrane, which is followed in real time. From a comparison of the binding rates of PSP and PSP from which the lipid moiety has been removed, it is shown that the lipid moiety plays a key role in anchoring the protein to the membrane. Specific and nonspecific binding of antibodies to membrane-anchored PSP is also investigated. As little as a fifth of a monolayer of PSP is sufficient to suppress the appreciable nonspecific binding of antibodies to the membrane.

Computer-aided volume measurement of posttraumatic orbits reconstructed with AO titanium mesh plates: accuracy and reliability

PURPOSE: To prospectively evaluate the accuracy and reliability of "freehand" posttraumatic orbital wall reconstruction with AO (Arbeitsgemeinschaft Osteosynthese) titanium mesh plates by using computer-aided volumetric measurement of the bony orbits. METHODS: Bony orbital volume was measured in 12 patients from coronal CT scan slices using OsiriX Medical Image software. After defining the volumetric limits of the orbit, the segmentation of the bony orbital region of interest of each single slice was performed. At the end of the segmentation process, all regions of interest were grouped and the volume was computed. The same procedure was performed on both orbits, and thereafter the volume of the contralateral uninjured orbit was used as a control for comparison. RESULTS: In all patients, the volume data of the reconstructed orbit fitted that of the contralateral uninjured orbit with accuracy to within 1.85 cm3 (7%). CONCLUSIONS: This preliminary study has demonstrated that posttraumatic orbital wall reconstruction using "freehand" bending and placement of AO titanium mesh plates results in a high success rate in re-establishing preoperative bony volume, which closely approximates that of the contralateral uninjured orbit.

Multi-analyte detection for biological fluids. Towards continous monitoring of glucose, ionized calcium and pH using a viscometric affinity biosensor.

We present a viscometric affinity biosensor that can potentially allow continuous multi-analyte monitoring in biological fluids like blood or plasma. The sensing principle is based on the detection of viscosity changes of a polymeric solution which has a selective affinity for the analyte of interest. The chemico-mechanical sensor incorporates an actuating piezoelectric diaphragm, a sensing piezoelectric diaphragm and a flow-resisting microchannel for viscosity detection. A free-standing Anodic Alumina Oxide (AAO) porous nano-membrane is used as selective interface. A glucose-sensitive sensor was fabricated and extensively assessed in buffer solution. The sensor reversibility, stability and sensitivity were excellent during at least 65 hours. Results showed also a good degree of stability for a long term measurement (25 days). The sensor behaviour was furthermore tested in fetal bovine serum (FBS). The obtained results for glucose sensing are very promising, indicating that the developed sensor is a candidate for continuous monitoring in biological fluids. Sensitive solutions for ionized calcium and pH are currently under development and should allow multi-analyte sensing in the near future.

Care delivery value chains for ophthalmic clinics in Switzerland

Perceived patient value is often not aligned with the emerging expenses for health care services. In other words, the costs are often supposed as rising faster than the actual value for the patients. This fact is causing major concerns to governments, health plans, and individuals. Attempts to solve the problem have habitually been on the operational effectiveness side: increasing patient volume, minimizing costs, rationing, or closing hospitals, usually resulting in a zero-sum game. Only few approaches come from the strategic positioning side and "competition" among hospitals is still perceived rather as a danger than as a chance to create a positive-sum game and stimulate patient value. In their 2006 book, "Redefining Health Care", the renowned Harvard strategy professor Michael E. Porter and hospital management expert Professor Elizabeth Olmsted Teisberg approach the challenge from the positive-sum perspective: they propose to form Integrated Practice Units (IPUs) and manage hospitals in a modern, patient value oriented way. They argue that creating value-based competition on results should have the same effect on the health care sector like transparency and competition turned other industries with out-dated management models (like recently the inert telecommunication industry) into highly competitive and customer value creating businesses. The objective of this paper is to elaborate Care Delivery Value Chains for Integrated Practice Units in ophthalmic clinics and gather a first feedback from Swiss hospital managers, ophthalmologists, and patients, if such an approach could be a realistic way to improve health care management. First, Porter's definition of competitiveness (distinction between operational effectiveness and strategic positioning) is explained. Then, the Care Delivery Value Chain is introduced as a key element for understanding value-based management, followed by three practice examples for ophthalmic clinics. Finally, recommendations are given how the Care Delivery Value Chain can be managed efficiently and how the obstacles of becoming a patient-oriented organization can be overcome. The conclusion is that increased transparency and value-based competition on results has the potential to change the mindset of hospital managers-which will align patient value with the emerging health care expenses. Early adapters of this management approach will gain a competitive advantage. [Author, p. 6]

Advantages of digital holographic microscopy for real-time full field absolute phase imaging

Different interferometric techniques were developed last decade to obtain full field, quantitative, and absolute phase imaging, such as phase-shifting, Fourier phase microscopy, Hilbert phase microscopy or digital holographic microscopy (DHM). Although, these techniques are very similar, DHM combines several advantages. In contrast, to phase shifting, DHM is indeed capable of single-shot hologram recording allowing a real-time absolute phase imaging. On the other hand, unlike to Fourier phase or Hilbert phase microscopy, DHM does not require to record in focus images of the specimen on the digital detector (CCD or CMOS camera), because a numerical focalization adjustment can be performed by a numerical wavefront propagation. Consequently, the depth of view of high NA microscope objectives is numerically extended. For example, two different biological cells, floating at different depths in a liquid, can be focalized numerically from the same digital hologram. Moreover, the numerical propagation associated to digital optics and automatic fitting procedures, permits vibrations insensitive full- field phase imaging and the complete compensation for a priori any image distortion or/and phase aberrations introduced for example by imperfections of holders or perfusion chamber. Examples of real-time full-field phase images of biological cells have been demonstrated. ©2008 COPYRIGHT SPIE

Real-time dual-wavelength digital holographic microscopy for extended measurement range with enhanced axial resolution

We report on advanced dual-wavelength digital holographic microscopy (DHM) methods, enabling single-acquisition real-time micron-range measurements while maintaining single-wavelength interferometric resolution in the nanometer regime. In top of the unique real-time capability of our technique, it is shown that axial resolution can be further increased compared to single-wavelength operation thanks to the uncorrelated nature of both recorded wavefronts. It is experimentally demonstrated that DHM topographic investigation within 3 decades measurement range can be achieved with our arrangement, opening new applications possibilities for this interferometric technique. ©2008 COPYRIGHT SPIE

Dual-wavelength digital holographic microscopy with sub-nanometer axial accuracy

We present dual-wavelength Digital Holographic Microscopy (DHM) measurements on a certified 8.9 nm high Chromium thin step sample and demonstrate sub-nanometer axial accuracy. We introduce a modified DHM Reference Calibrated Hologram (RCH) reconstruction algorithm taking into account amplitude contributions. By combining this with a temporal averaging procedure and a specific dual-wavelength DHM arrangement, it is shown that specimen topography can be measured with an accuracy, defined as the axial standard deviation, reduced to at least 0.9 nm. Indeed, it is reported that averaging each of the two wavefronts recorded with real-time dual-wavelength DHM can provide up to 30% spatial noise reduction for the given configuration, thanks to their non-correlated nature. ©2008 COPYRIGHT SPIE

Translation to success of surgical innovation.

Contemporary thoracic and cardiovascular surgery uses extensive equipment and devices to enable its performance. As the specialties develop and new frontiers are crossed, the technology needs to advance in a parallel fashion. Strokes of genius or problem-solving brain-storming may generate great ideas, but the metamorphosis of an idea into a physical functioning tool requires a lot more than just a thinking process. A modern surgical device is the end-point of a sophisticated, complicated and potentially treacherous route, which incorporates new skills and knowledge acquisition. Processes including technology transfer, commercialisation, corporate and product development, intellectual property and regulatory routes all play pivotal roles in this voyage. Many good ideas may fall by the wayside for a multitude of reasons as they may not be marketable or may be badly marketed. In this article, we attempt to illuminate the components required in the process of surgical innovation, which we believe must remain in the remit of the modern-day thoracic and cardiovascular surgeon.

A novel PIKFYVE mutation in fleck corneal dystrophy.

Purpose: To report the findings of the clinical and molecular evaluation in a Greek family with fleck corneal dystrophy (CFD).Methods: A 58-year-old woman was seen on routine ophthalmic examination and diagnosed as having CFD. All available family members were examined to evaluate the clinical findings and inheritance of the disease. Twenty members of the family in five generations underwent slit-lamp examination. Eleven were females and nine males, aged from two years to 85 years old. Blood samples were available from four patients with CFD and seven unaffected relatives, and the DNAs were subjected to molecular screening of the phosphoinositide kinase, five finger-containing (PIKFYVE) gene by direct sequencing or denaturing high performance liquid chromatography (DHPLC).Results: The clinical evaluation revealed six family members (five females and one male) with CFD. In two CFD patients early cataract formation was noticed. All patients affected with the corneal dystrophy were asymptomatic. The molecular analyses demonstrated the existence of a novel c. 3060-3063delCCTT (p.P968Vfs23) mutation in PIKFYVE in all CFD patients tested but in none of the six unaffected family members. No molecular screening was performed in the seventh unaffected member as the causative mutation was clearly transmitted from his affected wife to his affected son.Conclusions: We report on the clinical and molecular findings of a five generation Greek family with CFD and we conclude that the novel c. 3060-3063delCCTT (p. P968Vfs23) mutation in PIKFYVE, which segregated with the disease, was the causative mutation in this family.