Characterization of lead-recycling facility emissions at various workplaces : major insights for sanitary risks assessment

Most available studies on lead smelter emissions deal with the environmental impact of outdoor particles, but only a few focus on air quality at workplaces. The objective of this study is to physically and chemically characterize the Pb-rich particles emitted at different workplaces in a lead recycling plant. A multi-scale characterization was conducted from bulk analysis to the level of individual particles, to assess the particles properties in relation with Pb speciation and availability. Process PM from various origins were sampled and then compared; namely Furnace and Refining PM respectively present in the smelter and at refinery workplaces, Emissions PM present in channeled emissions.These particles first differed by their morphology and size distribution, with finer particles found in emissions. Differences observed in chemical composition could be explained by the industrial processes. All PM contained the same major phases (Pb, PbS, PbO, PbSO4 and PbO·PbSO4) but differed on the nature and amount of minor phases. Due to high content in PM, Pb concentrations in the CaCl2 extractant reached relatively high values (40 mg.L-1). However, the ratios (soluble/total) of CaCl2 exchangeable Pb were relatively low (< 0.02%) in comparison with Cd (up to 18%). These results highlight the interest to assess the soluble fractions of all metals (minor and major) and discuss both total metal concentrations and ratios for risk evaluations. In most cases metal extractability increased with decreasing size of particles, in particular, lead exchangeability was highest for channeled emissions. Such type of study could help in the choice of targeted sanitary protection procedures and for further toxicological investigations. In the present context, particular attention is given to Emissions and Furnace PM. Moreover, exposure to other metals than Pb should be considered. [Authors]

In vitro assessment of the pulmonary toxicity and gastric availability of lead-rich particles from a lead recycling plant

Epidemiological studies in urban areas have linked increasing respiratory and cardiovascular pathologies with atmospheric particulate matter (PM) from anthropic activities. However, the biological fate of metal-rich PM industrial emissions in urban areas of developed countries remains understudied. Lead toxicity and bioaccessibility assessments were therefore performed on emissions from a lead recycling plant, using complementary chemical acellular tests and toxicological assays, as a function of PM size (PM(10-2.5), PM(2.5-1) and PM(1)) and origin (furnace, refining and channeled emissions). Process PM displayed differences in metal content, granulometry, and percentage of inhalable fraction as a function of their origin. Lead gastric bioaccessibility was relatively low (maximum 25%) versus previous studies; although, because of high total lead concentrations, significant metal quantities were solubilized in simulated gastrointestinal fluids. Regardless of origin, the finest PM(1) particles induced the most significant pro-inflammatory response in human bronchial epithelial cells. Moreover, this biological response correlated with pro-oxidant potential assay results, suggesting some biological predictive value for acellular tests. Pulmonary effects from lead-rich PM could be driven by thiol complexation with either lead ions or directly on the particulate surface. Finally, health concern of PM was discussed on the basis of pro-inflammatory effects, accellular test results, and PM size distribution.

A regional Industrial Symbiosis methodology and its implementation in Geneva, Switzerland

The Agenda 21 for the Geneva region is the results from a broad consultation process including all local actors. The article 12 stipulates that « the State facilitates possible synergies between economic activities in order to minimize their environmental impacts » thus opening the way for Industrial Ecology (IE) and Industrial Symbiosis (IS). An Advisory Board for Industrial Ecology and Industrial Symbiosis implementation was established in 2002 involving relevant government agencies. Regulatory and technical conditions for IS are studied in the Swiss context. Results reveal that the Swiss law on waste does not hinder by-product exchanges. Methodology and technical factors including geographic, qualitative, quantitative and economical aspects are detailed. The competition with waste operators in a highly developed recycling system is also tackled.The IS project develops an empirical and systematic method for detecting and implementing by-products synergies between industrial actors disseminated throughout the Geneva region. Database management tool for the treatment of input-output analysis data and GIS tools for detecting potentials industrial partners are constantly improved. Potential symbioses for 17 flows (including energy, water and material flows) are currently studied for implementation.

CO2 utilization in the perspective of industrial ecology, an overview

Carbon dioxide emissions from anthropic activities have accumulated in the atmosphere in excess of 800 Gigatons since preindustrial times, and are continuously increasing. Among other strategies, CO2 capture and storage is one option to mitigate the emissions from large point sources. In addition, carbon dioxide extraction from ambient air is assessed to reduce the atmospheric concentration of CO2. Both direct and indirect (through photosynthesis) pathways are possible. Geological sequestration has significant disadvantages (high cost, low public acceptance, long term uncertainty) whereas carbon dioxide recycling (or utilization) is more consistent with the basic principle of industrial ecology, almost closing material cycles. In this article, a series of technologies for CO2 capture and valorization is described as integrated and optimized pathways. This integration increases the environmental and economic benefits of each technology. Depending on the source of carbon dioxide, appropriate capture and valorization processes are evaluated based on material and energy constraints.

Leniency programs, antitrust enforcement and multimarket contact : three essays in industrial organization

The Layout of My Thesis This thesis contains three chapters in Industrial Organization that build on the work outlined above. The first two chapters combine leniency programs with multimarket contact and provide a thorough analysis of the potential effects of Amnesty Plus and Penalty Plus. The third chapter puts the whole discussion on leniency programs into perspective by examining other enforcement tools available to an antitrust authority. The main argument in that last chapter is that a specific instrument can only be as effective as the policy in which it is embedded. It is therefore important for an antitrust authority to know how it best accompanies the introduction or modification of a policy instrument that helps deterrence. INTRODUCTION Chapter 1 examines the efféct of Amnesty Plus and Penalty Plus on the incentives of firms to report cartel activities. The main question is whether the inclusion of these policies in a leniency program undermine the effectiveness of the latter by discouraging the firms to apply for amnesty. The model is static and focus on the ex post incentives of firms to desist from collusion. The results suggest that, because Amnesty Plus and Penalty Plus encourage the reporting of a second cartel after a first detection, a firm, anticipating this, may be reluctant to seek leniency and to report in the first place. However, the effect may also go in the opposite direction, and Amnesty Plus and Penalty Plus may encourage the simultaneous reporting of two cartels. Chapter 2 takes this idea further to the stage of cartel formation. This chapter provides a complete characterization of the potential anticompetitive and procompetitive effects of Amnesty Plus in a infinitely repeated game framework when the firms use their multimarket contact to harshen punishment. I suggest a clear-cut policy rule that prevents potential adverse effects and thereby show that, if policy makers follow this rule, a leniency program with Amnesty Plus performs better than one without. Chapter 3 characterizes the socially optimal enforcement effort of an antitrust authority and shows how this effort changes with the introduction or modification of specific policy instruments. The intuition is that the policy instrument may increase the marginal benefit of conducting investigations. If this effect is strong enough, a more rigorous detection policy becomes socially desirable.

Flippase (FLP) recombinase-mediated marker recycling in the dermatophyte Arthroderma vanbreuseghemii.

Biological processes can be elucidated by investigating complex networks of relevant factors and genes. However, this is not possible in species for which dominant selectable markers for genetic studies are unavailable. To overcome the limitation in selectable markers for the dermatophyte Arthroderma vanbreuseghemii (anamorph: Trichophyton mentagrophytes), we adapted the flippase (FLP) recombinase-recombination target (FRT) site-specific recombination system from the yeast Saccharomyces cerevisiae as a selectable marker recycling system for this fungus. Taking into account practical applicability, we designed FLP/FRT modules carrying two FRT sequences as well as the flp gene adapted to the pathogenic yeast Candida albicans (caflp) or a synthetic codon-optimized flp (avflp) gene with neomycin resistance (nptII) cassette for one-step marker excision. Both flp genes were under control of the Trichophyton rubrum copper-repressible promoter (PCTR4). Molecular analyses of resultant transformants showed that only the avflp-harbouring module was functional in A. vanbreuseghemii. Applying this system, we successfully produced the Ku80 recessive mutant strain devoid of any selectable markers. This strain was subsequently used as the recipient for sequential multiple disruptions of secreted metalloprotease (fungalysin) (MEP) or serine protease (SUB) genes, producing mutant strains with double MEP or triple SUB gene deletions. These results confirmed the feasibility of this system for broad-scale genetic manipulation of dermatophytes, advancing our understanding of functions and networks of individual genes in these fungi.

Anatomy of contaminated aquifers of an industrial site: insights from the stable isotope compositions of waters and dissolved inorganic carbon

The hydrogen and oxygen isotopes of water and the carbon isotope composition of dissolved inorganic carbon (DIC) from different aquifers at an industrial site, highly contaminated by organic pollutants representing residues of the former gas production, have been used as natural tracers to characterize the hydrologic system. On the basis of their stable isotope compositions as well as the seasonal variations, different groups of waters (precipitation, surface waters, groundwaters and mineral waters) as well as seasonably variable processes of mixing between these waters can clearly be distinguished. In addition, reservoir effects and infiltration rates can be estimated. In the northern part of the site an influence of uprising mineral waters within the Quaternary aquifers, presumably along a fault zone, can be recognized. Marginal infiltration from the Neckar River in the cast and surface water infiltration adjacent to a steep hill on the western edge of the site with an infiltration rate of about one month can also be resolved through the seasonal variation. Quaternary aquifers closer to the centre of the site show no seasonal variations, except for one borehole close to a former mill channel and another borehole adjacent to a rain water channel. Distinct carbon isotope compositions and concentrations of DIC for these different groups of waters reflect variable influence of different components of the natural carbon cycle: dissolution of marine carbonates in the mineral waters, biogenic, soil-derived CO2 in ground- and surface waters, as well as additional influence of atmospheric CO2 for the surface waters. Many Quaternary aquifer waters have, however, distinctly lower delta(13)C(DIC) values and higher DIC concentrations compared to those expected for natural waters. Given the location of contaminated groundwaters at this site but also in the industrially well-developed valley outside of this site, the most likely source for the low C-13(DIC) values is a biodegradation of anthropogenic organic substances, in particular the tar oils at the site.

The Use of Passive Samplers to Reveal Industrial and Agricultural Pollution Trends in Swiss Rivers

This study shows the efficiency of passive sampling to reveal industrial and agricultural pollution trends. Two practical applications for nonpolar and polar contaminants are presented. Low-density polyethylene (LDPE) samplers were deployed for one year in the Venoge River (VD) to monitor indicator PCBs (iPCBs, IUPAC nos. 28, 52, 101, 138, 153 and 180). The results showed that the impact of PCB emissions into the river is higher in summer than in other seasons due to the low flow rate of the river during this period. P,olar organic chemical integrative samplers (POCIS) were deployed for 4 months in the Sion-Riddes canal (VS) to investigate herbicides (terbuthylazine, diuron and linuron). Desisopropylatrazine-d5 (DIA-d5) was tested as a performance reference compound (PRC) to estimate aqueous concentration. The results showed an increase of water contamination due to the studied agricultural area. The maximal contamination was observed in April and corresponds to the period of herbicide application on the crops.

Ecologie industrielle de l'aluminium, flux de matières et d'énergie : réalités et enjeux du recyclage

Dans les dernières années du 20ème siècle, l'aluminium a fait l'objet de beaucoup de communications outrancières et divergentes cautionnées par des scientifiques et des organismes faisant autorité. En 1986, la société PECHINEY le décrète perpétuel tel le mouvement « L'aluminium est éternel. Il est recyclable indéfiniment sans que ses propriétés soient altérées », ce qui nous avait alors irrité. Peu de temps après, en 1990, une communication tout aussi outrancière et irritante d'une grande organisation environnementale, le World Wild Fund, décrète que « le recyclage de l'aluminium est la pire menace pour l'environnement. Il doit être abandonné ». C'est ensuite à partir de la fin des années 1990, l'explosion des publications relatives au développement durable, le bien mal nommé. Au développement, synonyme de croissance obligatoire, nous préférons société ou organisation humaine et à durable, mauvaise traduction de l'anglais « sustainable », nous préférons supportable : idéalement, nous aurions souhaité parler de société durable, mais, pour être compris de tous, nous nous sommes limités à parler dorénavant de développement supportable. Pour l'essentiel, ces publications reconnaissent les très graves défauts de la métallurgie extractive de l'aluminium à partir du minerai et aussi les mérites extraordinaires du recyclage de l'aluminium puisqu'il représente moins de 10% de la consommation d'énergie de la métallurgie extractive à partir du minerai (on verra que c'est aussi moins de 10% de la pollution et du capital). C'est précisément sur le recyclage que se fondent les campagnes de promotion de l'emballage boisson, en Suisse en particulier. Cependant, les données concernant le recyclage de l'aluminium publiées par l'industrie de l'aluminium reflètent seulement en partie ces mérites. Dans les années 1970, les taux de croissance de la production recyclée sont devenus plus élevés que ceux de la production électrolytique. Par contre, les taux de recyclage, établis à indicateur identique, sont unanimement tous médiocres comparativement à d'autres matériaux tels le cuivre et le fer. Composante de l'industrie de l'aluminium, le recyclage bénéficie d'une image favorable auprès du grand public, démontrant le succès des campagnes de communication. A l'inverse, à l'intérieur de l'industrie de l'aluminium, c'est une image dévalorisée. Les opinions émises par tous les acteurs, commerçants, techniciens, dirigeants, encore recueillies pendant ce travail, sont les suivantes : métier de chiffonnier, métier misérable, métier peu technique mais très difficile (un recycleur 15 d'aluminium n'a-t-il pas dit que son métier était un métier d'homme alors que celui du recycleur de cuivre était un jeu d'enfant). A notre avis ces opinions appartiennent à un passé révolu qu'elles retraduisent cependant fidèlement car le recyclage est aujourd'hui reconnu comme une contribution majeure au développement supportable de l'aluminium. C'est bien pour cette raison que, en 2000, l'industrie de l'aluminium mondiale a décidé d'abandonner le qualificatif « secondaire » jusque là utilisé pour désigner le métal recyclé. C'est en raison de toutes ces données discordantes et parfois contradictoires qu'a débuté ce travail encouragé par de nombreuses personnalités. Notre engagement a été incontestablement facilité par notre connaissance des savoirs indispensables (métallurgie, économie, statistiques) et surtout notre expérience acquise au cours d'une vie professionnelle menée à l'échelle mondiale dans (recherche et développement, production), pour (recherche, développement, marketing, stratégie) et autour (marketing, stratégie de produits connexes, les ferro-alliages, et concurrents, le fer) de l'industrie de l'aluminium. Notre objectif est de faire la vérité sur le recyclage de l'aluminium, un matériau qui a très largement contribué à faire le 20ème siècle, grâce à une revue critique embrassant tous les aspects de cette activité méconnue ; ainsi il n'y a pas d'histoire du recyclage de l'aluminium alors qu'il est plus que centenaire. Plus qu'une simple compilation, cette revue critique a été conduite comme une enquête scientifique, technique, économique, historique, socio-écologique faisant ressortir les faits principaux ayant marqué l'évolution du recyclage de l'aluminium. Elle conclut sur l'état réel du recyclage, qui se révèle globalement satisfaisant avec ses forces et ses faiblesses, et au-delà du recyclage sur l'adéquation de l'aluminium au développement supportable, adéquation largement insuffisante. C'est pourquoi, elle suggère les thèmes d'études intéressant tous ceux scientifiques, techniciens, historiens, économistes, juristes concernés par une industrie très représentative de notre monde en devenir, un monde où la place de l'aluminium dépendra de son aptitude à satisfaire les critères du développement supportable. ABSTRACT Owing to recycling, the aluminium industry's global energetic and environmental prints are much lower than its ore extractive metallurgy's ones. Likewise, recycling will allow the complete use of the expected avalanche of old scraps, consequently to the dramatic explosion of aluminium consumption since the 50's. The recycling state is characterized by: i) raw materials split in two groups :one, the new scrap, internal and prompt, proportional to semi-finished and finished products quantities, exhibits a fairly good and regular quality. The other, the old scrap, proportional to the finished products arrivïng at their end-of--life, about 22 years later on an average, exhibits a variable quality depending on the collect mode. ii) a poor recycling rate, near by that of steel. The aluminium industry generates too much new internal scrap and doesn't collect all the availa~e old scrap. About 50% of it is not recycled (when steel is recycling about 70% of the old scrap flow). iii) recycling techniques, all based on melting, are well handled in spite of aluminium atiiníty to oxygen and the practical impossibility to purify aluminium from any impurity. Sorting and first collect are critical issues before melting. iv) products and markets of recycled aluminium :New scraps have still been recycled in the production lines from where there are coming (closed loop). Old scraps, mainly those mixed, have been first recycled in different production lines (open loop) :steel deoxidation products followed during the 30's, with the development of the foundry alloys, by foundry pieces of which the main market is the automotive industry. During the 80's, the commercial development of the beverage can in North America has permitted the first old scrap recycling closed loop which is developing. v) an economy with low and erratic margins because the electrolytic aluminium quotation fixes scrap purchasing price and recycled aluminium selling price. vi) an industrial organisation historically based on the scrap group and the loop mode. New scrap is recycled either by the transformation industry itself or by the recycling industry, the remelter, old scrap by the refiner, the other component of the recycling industry. The big companies, the "majors" are often involved in the closed loop recycling and very seldom in the open loop one. To-day, aluminium industry's global energetic and environmental prints are too unbeara~ e and the sustainaЫe development criteria are not fully met. Critical issues for the aluminium industry are to better produce, to better consume and to better recycle in order to become a real sustainaЫe development industry. Specific issues to recycling are a very efficient recycling industry, a "sustainaЫe development" economy, a complete old scrap collect favouring the closed loop. Also, indirectly connected to the recycling, are a very efficient transformation industry generating much less new scrap and a finished products industry delivering only products fulfilling sustainaЫe development criteria.