Evaporation from a shallow water table: Diurnal dynamics of measured and simulated water and heat regime at the vicinity of a drying sand surface

Accurate estimates of water losses by evaporation from shallow water tables are important for hydrological, agricultural, and climatic purposes. An experiment was conducted in a weighing lysimeter to characterize the diurnal dynamics of evaporation under natural conditions. Sampling revealed a completely dry surface sand layer after 5 days of evaporation. Its thickness was <1 cm early in the morning, increasing to reach 4?5 cm in the evening. This evidence points out fundamental limitations of the approaches that assume hydraulic connectivity from the water table up to the surface, as well as those that suppose monotonic drying when unsteady conditions prevail. The computed vapor phase diffusion rates from the apparent drying front based on Fick's law failed to reproduce the measured cumulative evaporation during the sampling day. We propose that two processes rule natural evaporation resulting from daily fluctuations of climatic variables: (i) evaporation of water, stored during nighttime due to redistribution and vapor condensation, directly into the atmosphere from the soil surface during the early morning hours, that could be simulated using a mass transfer approach and (ii) subsurface evaporation limited by Fickian diffusion, afterward. For the conditions prevailing during the sampling day, the amount of water stored at the vicinity of the soil surface was 0.3 mm and was depleted before 11:00. Combining evaporation from the surface before 11:00 and subsurface evaporation limited by Fickian diffusion after that time, the agreement between the estimated and measured cumulative evaporation was significantly improved.

Combined transesophageal and surface MRI provides optimal imaging in aortic atherosclerosis.

OBJECTIVE: Surface magnetic resonance imaging (MRI) for aortic plaque assessment is limited by the trade-off between penetration depth and signal-to-noise ratio (SNR). For imaging the deep seated aorta, a combined surface and transesophageal MRI (TEMRI) technique was developed 1) to determine the individual contribution of TEMRI and surface coils to the combined signal, 2) to measure the signal improvement of a combined surface and TEMRI over surface MRI, and 3) to assess for reproducibility of plaque dimension analysis. METHODS AND RESULTS: In 24 patients six black blood proton-density/T2-weighted fast-spin echo images were obtained using three surface and one TEMRI coil for SNR measurements. Reproducibility of plaque dimensions (combined surface and TEMRI) was measured in 10 patients. TEMRI contributed 68% of the signal in the aortic arch and descending aorta, whereas the overall signal gain using the combined technique was up to 225%. Plaque volume measurements had an intraclass correlation coefficient of as high as 0.97. CONCLUSION: Plaque volume measurements for the quantification of aortic plaque size are highly reproducible for combined surface and TEMRI. The TEMRI coil contributes considerably to the aortic MR signal. The combined surface and TEMRI approach improves aortic signal significantly as compared to surface coils alone. CONDENSED ABSTRACT: Conventional MRI aortic plaque visualization is limited by the penetration depth of MRI surface coils and may lead to suboptimal image quality with insufficient reproducibility. By combining a transesophageal MRI (TEMRI) with surface MRI coils we enhanced local and overall image SNR for improved image quality and reproducibility.

Oligopotent stem cells are distributed throughout the mammalian ocular surface.

The integrity of the cornea, the most anterior part of the eye, is indispensable for vision. Forty-five million individuals worldwide are bilaterally blind and another 135 million have severely impaired vision in both eyes because of loss of corneal transparency; treatments range from local medications to corneal transplants, and more recently to stem cell therapy. The corneal epithelium is a squamous epithelium that is constantly renewing, with a vertical turnover of 7 to 14 days in many mammals. Identification of slow cycling cells (label-retaining cells) in the limbus of the mouse has led to the notion that the limbus is the niche for the stem cells responsible for the long-term renewal of the cornea; hence, the corneal epithelium is supposedly renewed by cells generated at and migrating from the limbus, in marked opposition to other squamous epithelia in which each resident stem cell has in charge a limited area of epithelium. Here we show that the corneal epithelium of the mouse can be serially transplanted, is self-maintained and contains oligopotent stem cells with the capacity to generate goblet cells if provided with a conjunctival environment. Furthermore, the entire ocular surface of the pig, including the cornea, contains oligopotent stem cells (holoclones) with the capacity to generate individual colonies of corneal and conjunctival cells. Therefore, the limbus is not the only niche for corneal stem cells and corneal renewal is not different from other squamous epithelia. We propose a model that unifies our observations with the literature and explains why the limbal region is enriched in stem cells.

Staphylococcal biofilm formation on the surface of three different calcium phosphate bone grafts: a qualitative and quantitative in vivo analysis.

Differences in physico-chemical characteristics of bone grafts to fill bone defects have been demonstrated to influence in vitro bacterial biofilm formation. Aim of the study was to investigate in vivo staphylococcal biofilm formation on different calcium phosphate bone substitutes. A foreign-body guinea-pig infection model was used. Teflon cages prefilled with β-tricalcium phosphate, calcium-deficient hydroxyapatite, or dicalcium phosphate (DCP) scaffold were implanted subcutaneously. Scaffolds were infected with 2 × 10(3) colony-forming unit of Staphylococcus aureus (two strains) or S. epidermidis and explanted after 3, 24 or 72 h of biofilm formation. Quantitative and qualitative biofilm analysis was performed by sonication followed by viable counts, and microcalorimetry, respectively. Independently of the material, S. aureus formed increasing amounts of biofilm on the surface of all scaffolds over time as determined by both methods. For S. epidermidis, the biofilm amount decreased over time, and no biofilm was detected by microcalorimetry on the DCP scaffolds after 72 h of infection. However, when using a higher S. epidermidis inoculum, increasing amounts of biofilm were formed on all scaffolds as determined by microcalorimetry. No significant variation in staphylococcal in vivo biofilm formation was observed between the different materials tested. This study highlights the importance of in vivo studies, in addition to in vitro studies, when investigating biofilm formation of bone grafts.

VARIABILITY OF PHENOTYPIC, PROTEOMIC AND TRANSCRIPTOMIC EXPRESSION OF STAPHYLOCOCCUS AUREUS SURFACE ADHESINS

Staphylococcus aureus is a highly successful pathogen responsible of a wide variety of diseases, from minor skin infection to life-threatening sepsis or infective endocarditis, as well as food poisoning and toxic shock syndrome. This heterogeneity of infections and the ability of S. aureus to develop antibiotic-resistance to virtually any available drugs reflect its extraordinary capacity to adapt and survive in a great variety of environments. The pathogenesis of S. aureus infection involves a wide range of cell wall-associated adhesins and extracellular toxins that promote host colonization and invasion. In addition, S. aureus is extremely well equipped with regulatory systems that sense environmental conditions and respond by fine tuning the expression of metabolic and virulence determinants. Surface adhesins referred to MSCRAMMs - for Microbial Surface Component Recognizing Adherence Matrix Molecules - mediate binding to the host extracellular matrix or serum components, including fibrinogen, fibronectin, collagen and elastin, and promote tissue colonization and invasion. Major MSCRAMMs include a family of surface-attached proteins covalently bound to the cell wall peptidoglycan via a conserved LPXTG motif. Genomic analyses indicate that S. aureus contain up to 22 LPXTG surface proteins, which could potentially act individually or in synergy to promote infection. In the first part of this study we determined the range of adherence phenotypes to fibrinogen and fibronectin among 30 carriage isolates of S. aureus and compared it to the adherence phenotypes of 30 infective endocarditis and 30 blood culture isolates. Overall there were great variations in in vitro adherence, but no differences were observed between carriage and infection strains. We further determined the relation between in vitro adherence and in vivo infectivity in a rat model of experimental endocarditis, using 4 isolates that displayed either extremely low or high adherence phenotypes. Unexpectedly, no differences were observed between the in vivo infectivity of isolates that were poorly and highly adherent in vitro. We concluded that the natural variability of in vitro adherence to fibrinogen and fibronectin did not correlate with in vivo infectivity, and thus that pathogenic differences between various strains might only be expressed in in vivo conditions, but not in vitro. Therefore, considering the importance of adhesins expression for infection, direct measurement of those adhesins present on the bacterial surface were made by proteomic approach. 5 In the second series of experiments we assessed the physical presence of the LPXTG species at the staphylococcal surface, as measured at various time points during growth in different culture media. S. aureus Newman was grown in either tryptic soy broth (TSB) or in Roswell Park Memorial Institute (RPMI) culture medium, and samples were removed from early exponential growth phase to late stationary phase. Experiments were performed with mutants in the global accessory-gene regulator (agr), surface protein A (Spa) and clumping factor A (ClfA). Peptides of surface proteins were recovered by "trypsin-shaving" of live bacteria, and semi-quantitative proteomic analysis was performed by tandem liquid-chromatography and mass-spectrometry (LC-MS). We also determined in parallel the mRNA expression by microarrays analysis, as well as the phenotypic adherence of the bacteria to fibrinogen in vitro. The surface proteome was highly complex and contained numerous proteins theoretically not belonging to the bacterial envelope, including ribosomal proteins and metabolic enzymes. Sixteen of the 21 known LPXTG species were detected, but were differentially expressed. As expected, 9 known agr-regulated proteins (e.g. including Spa, FnBPA, ClfA, IsdA, IsdB, SasH, SasD, SasG and FmtB) increased up to the late exponential growth phase, and were abrogated in agr-negative mutants. However, only Spa and SasH modified their proteomic and mRNA profiles in parallel in the parent and its agr negative mutant, while all other LPXTG proteins modified their proteomic profiles independently of their mRNA. Moreover, ClfA became highly transcribed and active in in vitro fibrinogen adherence tests during late growth (24h), whereas it remained poorly detected by proteomics. Differential expression was also detected in iron-rich TSB versus iron-poor RPMI. Proteins from the iron-regulated surface determinant (isd) system, including IsdA, IsdB and IsdH were barely expressed in iron-rich TSB, whereas they increased their expression by >10 time in iron-poor RPMI. We conclude that semi-quantitative proteomic analysis of specific protein species is feasible in S. aureus and that proteomic, transcriptomic and adherence phenotypes demonstrated differential profiles in S. aureus. Furthermore, peptide signatures released by trypsin shaving suggested differential protein domain exposures in various environments, which might be relevant for antiadhesins vaccines. A comprehensive understanding of the S. aureus physiology should integrate all these approaches.

Measuring surface potential changes on leaves.

We provide here a detailed protocol for studying the changes in electrical surface potential of leaves. This method has been developed over the years by plant physiologists and is currently used in different variants in many laboratories. The protocol records surface potential changes to measure long-distance electrical signals induced by diverse stimuli such as leaf wounding or current injection. This technique can be used to determine signaling speeds, to measure the connectivity between different plant organs and-by exploiting mutant plants-to identify transporters and ion channels involved in electrical signaling. The approach can be combined with the analysis of mRNA expression and of metabolite concentrations to correlate electrical signaling to specific physiological events. We describe how to use this protocol on Arabidopsis, looking at the effects of leaf wounding; however, it is broadly applicable to other plants and can be used to study other aspects of plant physiology. After wound infliction, surface potential recording takes ∼20 min per plant.

Cis-trans interactions of cell surface receptors: biological roles and structural basis.

Cell surface receptors bind ligands expressed on other cells (in trans) in order to communicate with neighboring cells. However, an increasing number of cell surface receptors are found to also interact with ligands expressed on the same cell (in cis). These observations raise questions regarding the biological role of such cis interactions. Specifically, it is important to know whether cis and trans binding have distinct functional effects and, if so, how a single cell discriminates between interactions in cis versus trans. Further, what are the structural features that allow certain cell surface receptors to engage ligand both on the same as well as on an apposed cell membrane? Here, we summarize known examples of receptors that display cis-trans binding and discuss the emerging diversity of biological roles played by these unconventional two-way interactions, along with their structural basis.

Méthodologie intégrée de microgravimétrie en milieu urbain : test d'application au génie civil sur le métro M2 de Lausanne

RESUME Dès le printemps 2004, la construction d'une 2ème ligne de métro est entreprise dans la ville de Lausanne en Suisse. En reliant Ouchy, au bord du lac Léman (alt. 373 m) à Epalinges (alt. 711 m), le nouveau métro "M2" traversera dès 2008 l'agglomération lausannoise du Sud au Nord sur une distance de 6 km. Depuis l'avant-projet, en 1999, une grande quantité de données géologiques a été récolté et de nombreux forages exécutés sur le site. Ceci nous a donné une occasion unique d'entreprendre une étude de microgravimétrique urbaine de détail. Le mode de creusement du tunnel dépend fortement des matériaux à excaver et il est classiquement du domaine du géologue, avec ses connaissances de la géologie régionale et de la stratigraphie des forages, de fournir à l'ingénieur un modèle géologique. Ce modèle indiquera dans ce cas l'épaisseur des terrains meubles qui recouvrent le soubassement rocheux. La représentativité spatiale d'une information très localisée, comme celle d'un forage, est d'autant plus compliquée que le détail recherché est petit. C'est à ce moment là que la prospection géophysique, plus spécialement gravimétrique, peut apporter des informations complémentaires déterminantes pour régionaliser les données ponctuelles des forages. La microgravimétrie en milieu urbain implique de corriger avec soin les perturbations gravifiques sur la mesure de la pesanteur dues aux effets de la topographie, des bâtiments et des caves afin d'isoler l'effet gravifique dû exclusivement à l'épaisseur du remplissage des terrains meubles. Tenant compte de l'intensité des corrections topographiques en milieu urbain, nous avons donné une grande importance aux sous-sols, leurs effets gravifiques pouvant atteindre l'ordre du dixième de mGal. Nous avons donc intégré ces corrections celle de topographie et traité les effets des bâtiments de manière indépendante. Nous avons inclus dans le modèle numérique de terrain (MNT) la chaussée et les sous-sols afin de construire un modèle numérique de terrain urbain. Nous utiliserons un nouvel acronyme « MNTU »pour décrire ce modèle. Nous proposons d'établir des cartes de corrections topographiques préalables, basées sur les données à disposition fournies par le cadastre en faisant des hypothèses sur la profondeur des sous-sols et la hauteur des bâtiments. Les deux zones de test choisies sont caractéristiques des différents types d'urbanisation présente à Lausanne et se révèlent par conséquent très intéressantes pour élaborer une méthodologie globale de la microgravimétrie urbaine. Le but était d'évaluer l'épaisseur du remplissage morainique sur un fond rocheux molassique se situant à une profondeur variable de quelques mètres à une trentaine de mètres et d'en établir une coupe dans l'axe du futur tracé du métro. Les résultats des modélisations se sont révélés très convaincants en détectant des zones qui diffèrent sensiblement du modèle géologique d'avant projet. Nous avons également démontré que l'application de cette méthode géophysique, non destructive, est à même de limiter le nombre de sondages mécaniques lors de l'avant-projet et du projet définitif, ce qui peut limiter à la fois les coûts et le dérangement engendré par ces travaux de surface. L'adaptabilité de la technique gravimétrique permet d'intervenir dans toutes les différentes phases d'un projet de génie civil comme celui de la construction d'un métro en souterrain. KURZFASSUNG Seit dem Frühling 2004 ist in der Stadt Lausanne (Schweiz) die neue U-Bahn "M2" in Konstruktion. Diese soll auf 6 km Länge die Lausanner Agglomeration von Süd nach Nord durchqueren. Die dem Projekt zu Grunde liegende technische Planung sieht vor, daß die Bahnlinie hauptsächlich in der Molasse angesiedelt sein wird. Seit dem Vorentwurf (1999) ist eine große Anzahl geologischer Angaben gesammelt worden. Daraus ergab sich die einmalige Gelegenheit, die Informationen aus den damit verbundenen zahlreichen Bohrungen zu einer detaillierten mikrogravimetrischen Studie der Stadt Lausanne zu erweitern und zu vervollständigen. Das Ziel bestand darin, die Mächtigkeit der die Molasseüberdeckenden Moräneablagerung abzuschätzen, um eine entsprechendes geologisches Profile entlang der künftigen Bahnlinie zu erstellen. Weiterhin sollte gezeigt werden, daß die Anwendung dieser nicht-invasiven geophysikalischen Methode es ermöglicht, die Anzahl der benötigten Bohrungen sowohl in der Pilotphase wie auch im endgültigen Projekt zu reduzieren, was zu wesentlichen finanziellen Einsparungen in der Ausführung des Werkes beitragen würde. Die beiden in dieser Studie bearbeiteten Testzonen befinden sich im Nordteil und im Stadtzentrum von Lausanne und sind durch eine unterschiedliche Urbanisierung charakterisiert. Das anstehende Gestein liegt in verschiedenen Tiefen: von einigen Metern bis zu etwa dreißig Metern. Diese Zonen weisen alle Schwierigkeiten einer urbanen Bebauung mit hoher Verkehrsdichte auf und waren daher massgebend bei der Ausarbeitung einer globalen mikrogravimetrischen Methodologie für die Stadt Lausanne. Die so entwickelte Technik ermöglicht, die störenden Auswirkungen der Topographie, der Gebäude, der Keller und der Öffentlichen Infrastrukturen sorgfältig zu korrigieren, um so die ausschließlich auf die Mächtigkeit des Lockergesteins zurückzuführenden Effekte zu isolieren. In Bezug auf die Intensität der Auswirkungen der topographischen Korrekturen im Stadtgebiet wurde den Untergeschossen eine besonders grosse Bedeutung zugemessen da die entsprechenden Schwerkrafteffekte eine Grösse von rund einem Zehntel mGal erreichen können. Wir schlagen deshalb vor, vorläufige Karten der topographischen Korrekturen zu erstellen. Diese Korrekturen basieren auf den uns vom Katasterplan gelieferten Daten und einigen Hypothesen bezüglich der Tiefe der Untergeschosse und der Höhe der Gebäude. Die Verfügbarkeit einer derartigen Karte vor der eigentlichen gravimetrischen Messkampagne würde uns erlauben, die Position der Meßstationen besser zu wählen. Wir sahen zudem, daß ein entsprechenden a priori Filter benutzt werden kann, wenn die Form und die Intensität der Anomalie offensichtlich dem entsprechenden Gebäude zugeordnet werden können. Diese Strategie muß jedoch mit Vorsicht angewandt werden, denn falls weitere Anomalien dazukommen, können bedeutende Verschiebungen durch Übèrlagerungen der Schwerewirkung verschiedener Strukturen entstehen. Die Ergebnisse der Modellierung haben sich als sehr überzeugend erwiesen, da sie im Voraus unbekannte sensible Zonen korrekt identifiziert haben. Die Anwendbarkeit der in dieser Arbeit entwickelten gravimetrischen Technik ermöglicht es, während allen Phasen eines Grossbauprojekts, wie zum Beispiel bei der Konstruktion einer unterirdischen U-Bahn, einzugreifen. ABSTRACT Since Spring of 2004 a new metro line has been under construction in the city of Lausanne in Switzerland. The new line, the M2, will be 6 km long and will traverse the city from south to north. The civil engineering project determined that the line would be located primarily in the Molasse. Since the preparatory project in 1999, a great quantity of geological data has been collected, and the many drillings made on the site have proved to be a unique opportunity to undertake a study of urban microgravimetry. The goal was to evaluate the thickness of the morainic filling over the molassic bedrock, and to establish a section along the axis of the future line. It then had to be shown that the application of this nondestructive geophysical method could reduce the number of mechanical surveys required both for a preparatory and a definitive project, which would lead to real savings in the realization of a civil engineering project. The two test zones chosen, one in the northern part of the city and one in the city centre, are characterised by various types of urbanisation. Bedrock is at a depth varying from a few metres to about thirty metres. These zones well exemplify the various difficulties encountered in an urban environment and are therefore very interesting for the development of an overall methodology of urban microgravimetry. Microgravimetry in an urban environment requires careful corrections for gravific disturbances due to the effects of topography, buildings, cellars, and the infrastructure of distribution networks, in order to isolate the gravific effect due exclusively to the thickness of loose soil filling. Bearing in mind the intensity of the topographic corrections in an urban environment, we gave particular importance to basements. Their gravific effects can reach the order of one tenth of one meal, and can influence above all the precision of the Bouguer anomaly. We propose to establish preliminary topographic correction charts based on data provided to us by the land register, by making assumptions on the depths of basements and the heights of buildings. Availability of this chart previous to a gravimetry campaign would enable us to choose optimum measuring sites. We have also seen that an a priori filter can be used when the form and the intensity of the anomaly correspond visually to the corresponding building. This strategy must be used with caution because if other anomalies are to be associated, important shifts can be generated by the superposition of the effects of different structures. The results of the model have proved to be very convincing in detecting previously unknown sensitive zones. The adaptability of the gravimetry technique allows for application in all phases of a civil engineering project such as the construction of an underground metro line. RIASSUNTO Dalla primavera 2004 una nuova linea metropolitana é in costruzione nella città di Losanna in Svizzera. La nuova metropolitana "M2" traverserà per la lunghezza di 6 km il centro urbano di Losanna da sud a nord. II progetto d'ingegneria civile prevedeva un tracciato situato essenzialmente nel fondo roccioso arenaceo terziario (molassa). Dalla redazione del progetto preliminare, avvenuta nel 1999, una grande quantità di dati geologici sono stati raccolti e sono stati eseguiti numerosi sondaggi. Questo sì é presentato come un'occasione unica per mettere a punto uno studio microgravimetrico in ambiente urbano con lo scopo di valutare lo spessore dei terreni sciolti di origine glaciale che ricoprono il fondo roccioso di molassa e di mettere in evidenza come l'applicazione di questo metodo geofisico non distruttivo possa limitare il numero di sondaggi meccanici nella fase di progetto preliminare ed esecutivo con conseguente reale risparmio economico nella realizzazione di una tale opera. Le due zone di test sono situate una nella zona nord e la seconda nel centro storico di Losanna e sono caratterizzate da stili architettonici differenti. II fondo roccioso é situato ad una profondità variabile da qualche metro ad una trentina. Queste due zone sembrano ben rappresentare tutte le difficoltà di un ambiente urbano e ben si prestano per elaborare una metodologia globale per la microgravimetria in ambiente urbano. L'applicazione di questa tecnica nell'ambiente suddetto implica la correzione attenta delle perturbazioni sulla misura dell'accelerazione gravitazionale, causate dalla topografia, gli edifici, le cantine e le infrastrutture dei sottoservizi, per ben isolare il segnale esclusivamente causato dallo spessore dei terreni sciolti. Tenuto conto, dell'intensità delle correzioni topografiche, abbiamo dato grande importanza alle cantine, poiché il loro effetto sulle misure può raggiungere il decimo di mGal. Proponiamo quindi di redigere una carta delle correzioni topografiche preliminare all'acquisizione, facendo delle ipotesi sulla profondità delle cantine e sull'altezza degli edifici, sulla base delle planimetrie catastali. L'analisi di questa carta permetterà di scegliere le posizioni più adatte per le stazioni gravimetriche. Abbiamo anche osservato che un filtro a priori, qualora la forma e l'intensità dell'anomalia fosse facilmente riconducibile in maniera visuale ad un edificio, possa essere efficace. Tuttavia questa strategia deve essere utilizzata con precauzione, poiché può introdurre uno scarto, qualora più anomalie, dovute a differenti strutture, si sovrappongano. I risultati delle modellizzazioni si sono rivelati convincenti, evidenziando zone sensibili non conosciute preventivamente. L'adattabilità della tecnica gravimetrica ha mostrato di poter intervenire in differenti fasi di un progetto di ingegneria civile, quale è quella di un'opera in sotterraneo.

Vasopressin-inducible ubiquitin-specific protease 10 increases ENaC cell surface expression by deubiquitylating and stabilizing sorting nexin 3

Adjustment of Na+ balance in extracellular fluids is achieved by regulated Na+ transport involving the amiloride-sensitive epithelial Na+ channel (ENaC) in the distal nephron. In this context, ENaC is controlled by a number of hormones, including vasopressin, which promotes rapid translocation of water and Na+ channels to the plasma membrane and long-term effects on transcription of vasopressin-induced and -reduced transcripts. We have identified a mRNA encoding the deubiquitylating enzyme ubiquitin-specific protease 10 (Usp10), whose expression is increased by vasopressin at both the mRNA and the protein level. Coexpression of Usp10 in ENaC-transfected HEK-293 cells causes a more than fivefold increase in amiloride-sensitive Na+ currents, as measured by whole cell patch clamping. This is accompanied by a three- to fourfold increase in surface expression of alpha- and gamma-ENaC, as shown by cell surface biotinylation experiments. Although ENaC is well known to be regulated by its direct ubiquitylation, Usp10 does not affect the ubiquitylation level of ENaC, suggesting an indirect effect. A two-hybrid screen identified sorting nexin 3 (SNX3) as a novel substrate of Usp10. We show that it is a ubiquitylated protein that is degraded by the proteasome; interaction with Usp10 leads to its deubiquitylation and stabilization. When coexpressed with ENaC, SNX3 increases the channel's cell surface expression, similarly to Usp10. In mCCD(cl1) cells, vasopressin increases SNX3 protein but not mRNA, supporting the idea that the vasopressin-induced Usp10 deubiquitylates and stabilizes endogenous SNX3 and consequently promotes cell surface expression of ENaC

Effects of the playing surface on plantar pressures during the first serve in tennis.

PURPOSE: This study aimed at examining the influence of different playing surfaces on in-shoe loading patterns in each foot (back and front) separately during the first serve in tennis. METHODS: Ten competitive tennis players completed randomly five first (ie, flat) serves on two different playing surfaces: clay vs GreenSet. Maximum and mean force, peak and mean pressure, mean area, contact area and relative load were recorded by Pedar insoles divided into 9 areas for analysis. RESULTS: Mean pressure was significantly lower (123 ± 30 vs 98 ± 26 kPa; -18.5%; P < .05) on clay than on GreenSet when examining the entire back foot. GreenSet induced higher mean pressures under the medial forefoot, lateral forefoot and hallux of the back foot (+9.9%, +3.5% and +15.9%, respectively; both P < .01) in conjunction with a trend toward higher maximal forces in the back hallux (+15.1%, P = .08). Peak pressures recorded under the central and lateral forefoot (+21.8% and +25.1%; P < .05) of the front foot but also the mean area values measured on the back medial and lateral midfoot were higher (P < .05) on clay. No significant interaction between foot region and playing surface on relative load was found. CONCLUSIONS: It is suggested that in-shoe loading parameters characterizing the first serve in tennis are adjusted according to the ground type surface. A lesser asymmetry in peak (P < .01) and mean (P < .001) pressures between the two feet was found on clay, suggesting a greater need for stability on this surface.

Respective roles of calcitonin receptor-like receptor (CRLR) and receptor activity-modifying proteins (RAMP) in cell surface expression of CRLR/RAMP heterodimeric receptors.

Receptor activity modifying proteins RAMP1, RAMP2, and RAMP3 are responsible for defining affinity to ligands of the calcitonin receptor-like receptor (CRLR). It has also been proposed that receptor activity-modifying proteins (RAMP) are molecular chaperones required for CRLR transport to the cell surface. Here, we have studied the respective roles of CRLR and RAMP in transporting CRLR/RAMP heterodimers to the plasma membrane by using a highly specific binding assay that allows quantitative detection of cell surface-expressed CRLR or RAMP in the Xenopus oocytes expression system. We show that: (i) heterodimer assembly is not a prerequisite for efficient cell surface expression of CRLR, (ii) N-glycosylated RAMP2 and RAMP3 are expressed at the cell surface and their transport to the plasma membrane requires N-glycans, (iii) RAMP1 is not N-glycosylated and is transported to the plasma membrane only upon formation of heterodimers with CRLR, and (iv) introduction of N-glycosylation sites in the RAMP1 sequence (D58N/G60S, Y71N, and K103N/P105S) allows cell surface expression of these mutants at levels similar to that of wild-type RAMP1 co-expressed with CRLR. Our data argue against a chaperone function for RAMP and identify the role of N-glycosylation in targeting these molecules to the cell surface.

Direct simulation of interface dynamics: linking capillary pressure, interfacial area and surface energy

We perform direct numerical simulations of drainage by solving Navier- Stokes equations in the pore space and employing the Volume Of Fluid (VOF) method to track the evolution of the fluid-fluid interface. After demonstrating that the method is able to deal with large viscosity contrasts and to model the transition from stable flow to viscous fingering, we focus on the definition of macroscopic capillary pressure. When the fluids are at rest, the difference between inlet and outlet pressures and the difference between the intrinsic phase average pressure coincide with the capillary pressure. However, when the fluids are in motion these quantities are dominated by viscous forces. In this case, only a definition based on the variation of the interfacial energy provides an accurate measure of the macroscopic capillary pressure and allows separating the viscous from the capillary pressure components.

Characterization of a surface metalloprotease from Herpetomonas samuelpessoai and comparison with Leishmania major promastigote surface protease.

The monogenetic kinetoplastid protozoan parasite Herpetomonas samuelpessoai expresses a surface-exposed metalloprotease. Comparable to the Leishmania promastigote surface protease, or PSP, the protease of Herpetomonas is active at the surface of fixed and live organisms, and both enzymes display an identical cleavage specificity toward a nonapeptide substrate. The protease was enriched 440 times by partition into Triton X-114 followed by 2 steps of anion exchange chromatography. The 56-kDa enzyme is inhibited by the metal chelator 1,10-phenanthroline and is susceptible to cleavage by glycosyl-phosphatidylinositol phospholipase C (GPI-PLC). The conservation of an identical surface protease activity in these monogenetic and digenetic trypanosomatids suggests that the enzyme has a physiological function in the promastigote (insect) stage of these parasites.

HLA-C cell surface expression and control of HIV/AIDS correlate with a variant upstream of HLA-C.

A variant 35 kb upstream of the HLA-C gene (-35C/T) was previously shown to associate with HLA-C mRNA expression level and steady-state plasma HIV RNA levels. We genotyped this variant in 1,698 patients of European ancestry with HIV. Individuals with known seroconversion dates were used for disease progression analysis and those with longitudinal viral load data were used for viral load analysis. We further tested cell surface expression of HLA-C in normal donors using an HLA-C-specific antibody. We show that the -35C allele is a proxy for high HLA-C cell surface expression, and that individuals with high-expressing HLA-C alleles progress more slowly to AIDS and control viremia significantly better than individuals with low HLA-C expressing alleles. These data strongly implicate high HLA-C expression levels in more effective control of HIV-1, potentially through better antigen presentation to cytotoxic T lymphocytes or recognition and killing of infected cells by natural killer cells.