Official Positions for FRAX(®) clinical regarding glucocorticoids: the impact of the use of glucocorticoids on the estimate by FRAX(®) of the 10 year risk of fracture from Joint Official Positions Development Conference of the International Society for Clinical Densitometry and International Osteoporosis Foundation on FRAX(®).

Given the significant impact the use of glucocorticoids can have on fracture risk independent of bone density, their use has been incorporated as one of the clinical risk factors for calculating the 10-year fracture risk in the World Health Organization's Fracture Risk Assessment Tool (FRAX(®)). Like the other clinical risk factors, the use of glucocorticoids is included as a dichotomous variable with use of steroids defined as past or present exposure of 3 months or more of use of a daily dose of 5 mg or more of prednisolone or equivalent. The purpose of this report is to give clinicians guidance on adjustments which should be made to the 10-year risk based on the dose, duration of use and mode of delivery of glucocorticoids preparations. A subcommittee of the International Society for Clinical Densitometry and International Osteoporosis Foundation joint Position Development Conference presented its findings to an expert panel and the following recommendations were selected. 1) There is a dose relationship between glucocorticoid use of greater than 3 months and fracture risk. The average dose exposure captured within FRAX(®) is likely to be a prednisone dose of 2.5-7.5 mg/day or its equivalent. Fracture probability is under-estimated when prednisone dose is greater than 7.5 mg/day and is over-estimated when the prednisone dose is less than 2.5 mg/day. 2) Frequent intermittent use of higher doses of glucocorticoids increases fracture risk. Because of the variability in dose and dosing schedule, quantification of this risk is not possible. 3) High dose inhaled glucocorticoids may be a risk factor for fracture. FRAX(®) may underestimate fracture probability in users of high dose inhaled glucocorticoids. 4) Appropriate glucocorticoid replacement in individuals with adrenal insufficiency has not been found to increase fracture risk. In such patients, use of glucocorticoids should not be included in FRAX(®) calculations.

Chances and risks of nanomaterials for health and environment

Nanomaterials have properties that are often very different from normal materials made of the same substance, which can be used to create novel products with exciting properties. However, the health and environmental impact of these nanomaterials is also changed and their potential risk needs to be studied. There is evidence that some nanomaterials can pass through tissue barriers (including the blood-brain barrier) and cell membranes. This is interesting for medical applications, but it raises concerns about the impact of non-medical nanomaterials. Current research aims at better coordinating research efforts and at better communication between researchers and involved stakeholders. Many research labs and production sites currently follow strategies that were established for dealing with very toxic chemicals and powders, until future research in this field helps identify the appropriate level of protection. All these efforts will ultimately ensure a safe, healthy and environmental friendly production, use and disposal of nanomaterials.

Health effects of occupational exposure to traffic particles and noise

Exposure to fine particles and noise has been linked to cardiovascular diseases and elevated cardiovascular mortality affecting the worldwide population. Residence and/or work in proximity to emission sources as for example road traffic leads to an elevated exposure and a higher risk for adverse health effects. Highway maintenance workers spend most of their work time in traffic and are exposed regularly to particles and noise. The aims of this thesis were to provide a better understanding of the workers' mixed exposure to particles and noise and to assess cardiopulmonary short term health effects in relation to this exposure. Exposure and health data were collected in collaboration with 8 maintenance centers of the Swiss Road Maintenance Services located in the cantons Bern, Fribourg and Vaud in western Switzerland. Repeated measurements with 18 subjects were conducted during 50 non-consecutive work shifts between Mai 2010 and February 2012, equally distributed over all seasons. In the first part of this thesis we tested and validated measurements of ultrafine particles with a miniature diffusion size classifier (miniDiSC) - a novel particle counting device that was used for the exposure assessment during highway maintenance work. We found that particle numbers and average particle size measured by the miniDiSC were highly correlated with data from the P-TRAK, a condensation particle counter (CPC), as well as from a scanning mobility particle sizer (SMPS). However, the miniDiSC measured significantly more particles than the P-TRAK and significantly less than the SMPS in its full size range. Our data suggests that the instrument specific cutoffs were the main reason for the different particle counts. The first main objective of this thesis was to investigate the exposure of highway maintenance workers to air pollutants and noise, in relation to the different maintenance activities. We have seen that the workers are regularly exposed to high particle and noise levels. This was a consequence of close proximity to highway traffic and the use of motorized working equipment such as brush cutters, chain saws, generators and pneumatic hammers during which the highest exposure levels occurred. Although exposure to air pollutants were not critical if compared to occupational exposure limits, the elevated exposure to particles and noise may lead to a higher risk for cardiovascular diseases in this worker population. The second main objective was to investigate cardiopulmonary short-term health effects in relation to the particle and noise exposure during highway maintenance work. We observed a PM2.5 related increase of the acute-phase inflammation markers C-reactive protein and serum amyloid A and a decrease of TNFa. Heart rate variability increased as a consequence of particle as well as noise exposure. Increased high frequency power indicated a stronger parasympathetic influence on the heart. Elevated noise levels during recreational time, after work, were related to increased blood pressure. Our data confirmed that highway maintenance workers are exposed to elevated levels of particles and noise as compared to the average population. This exposure poses a cardiovascular health risk and it is therefore important to make efforts to better protect the workers health. The use of cleaner machines during maintenance work would be a major step to improve the workers' situation. Furthermore, regulatory policies with the aim of reducing combustion and non-combustion emissions from road traffic are important for the protection of workers in traffic environments and the entire population.

Health at work and risk factors related to ergonomics: some results from the Swiss sample of the 4th European working conditions survey

Introduction The European Foundation for the improvement of living and working conditions conducts a survey every 5 years since 1990. The foundation also offers the possibility to non-EU countries to be included in the survey: in 2005, Switzerland took part for the first time in the fourth edition of this survey. The Institute for Work and Health (IST) has been associated to the Swiss project conducted under the leadership of the SECO and the Fachhochschule Nordwestschweiz. The survey covers different aspects of work like job characteristics and employment conditions, health and safety, work organization, learning and development opportunities, and the balance between working and non-working life (Parent-Thirion, Fernandez Macias, Hurley, & Vermeylen, 2007). More particularly, one question assesses the worker's self-perception of the effects of work on health. We identified (for the Swiss sample) several factors affecting the risk to report health problems caused by work. The Swiss sample includes 1040 respondents. Selection of participants was based on a random multi-stage sampling and was carried out by M.I.S Trend S.A. (Lausanne). Participation rate was 59%. The database was weighted by household size, gender, age, region of domicile, occupational group, and economic sector. Specially trained interviewers carried out the interviews at the respondents home. The survey was carriedout between the 19th of September 2005 and the 30th of November 2005. As detailed in (Graf et al., 2007), 31% of the Swiss respondents identify work as the cause of health problems they experience. Most frequently reported health problems include back pain (18%), stress (17%), muscle pain (13%), and overall fatigue (11%). Ergonomic aspects associated with higher risk of reporting health problems caused by work include frequent awkward postures (odds ratio [OR] 4.7, 95% confidence interval [CI] 3.1 to 5.4), tasks involving lifting heavy loads (OR 2.7, 95% CI 2.0 to 3.6) or lifting people (OR 2.2, 95% CI 1.4 to 3.5), standing or walking (OR 1.4, 95% CI 1.1 to 1.9), as well as repetitive movements (OR 1.7, 95% CI 1.3 to 2.3). These results highlight the need to continue and intensify the prevention of work related health problems in occupations characterized by risk factors related to ergonomics.

Perception et communication du risque: du diabète à la maladie cardiovasculaire [Risk perception and communication: from diabetes to cardiovascular diseases].

Evidence-based medicine has enabled to approach disease in a more rational and scientific way. Clinical research has identified behaviours and risk factors that could cause disease often "silent" at the beginning, such as diabetes. Despite the clear impact of these evidences on public health, it seems that the individual risk perception level remains weak. To mention as well, the health professionals very often have a different views, which makes it difficult to communicate the risk with patients. In this article we describe the principles of risk perception, the diabetes related risk perception concerning cardiovascular complications, and suggest some practical strategies and tools which could improve risk communication in the everyday practice.

Prevalence of cardiovascular risk factors in a middle-income country and estimated cost of a treatment strategy.

BACKGROUND: We assessed the prevalence of risk factors for cardiovascular disease (CVD) in a middle-income country in rapid epidemiological transition and estimated direct costs for treating all individuals at increased cardiovascular risk, i.e. following the so-called "high risk strategy". METHODS: Survey of risk factors using an age- and sex-stratified random sample of the population of Seychelles aged 25-64 in 2004. Assessment of CVD risk and treatment modalities were in line with international guidelines. Costs are expressed as USD per capita per year. RESULTS: 1255 persons took part in the survey (participation rate of 80.2%). Prevalence of main risk factors was: 39.6% for high blood pressure (> or =140/90 mmHg or treatment) of which 59% were under treatment; 24.2% for high cholesterol (> or =6.2 mmol/l); 20.8% for low HDL-cholesterol (<1.0 mmol/l); 9.3% for diabetes (fasting glucose > or =7.0 mmol/l); 17.5% for smoking; 25.1% for obesity (body mass index > or =30 kg/m2) and 22.1% for the metabolic syndrome. Overall, 43% had HBP, high cholesterol or diabetes and substantially increased CVD risk. The cost for medications needed to treat all high-risk individuals amounted to USD 45.6, i.e. 11.2 dollars for high blood pressure, 3.8 dollars for diabetes, and 30.6 dollars for dyslipidemia (using generic drugs except for hypercholesterolemia). Cost for minimal follow-up medical care and laboratory tests amounted to 22.6 dollars. CONCLUSION: High prevalence of major risk factors was found in a rapidly developing country and costs for treatment needed to reduce risk factors in all high-risk individuals exceeded resources generally available in low or middle income countries. Our findings emphasize the need for affordable cost-effective treatment strategies and the critical importance of population strategies aimed at reducing risk factors in the entire population.

Assessment of the occurrence of nanoparticles in Swiss industry and evaluation of the appropriatenesss of the measurement devices to determine the workforce exposure

Abstract : The occupational health risk involved with handling nanoparticles is the probability that a worker will experience an adverse health effect: this is calculated as a function of the worker's exposure relative to the potential biological hazard of the material. Addressing the risks of nanoparticles requires therefore knowledge on occupational exposure and the release of nanoparticles into the environment as well as toxicological data. However, information on exposure is currently not systematically collected; therefore this risk assessment lacks quantitative data. This thesis aimed at, first creating the fundamental data necessary for a quantitative assessment and, second, evaluating methods to measure the occupational nanoparticle exposure. The first goal was to determine what is being used where in Swiss industries. This was followed by an evaluation of the adequacy of existing measurement methods to assess workplace nanopaiticle exposure to complex size distributions and concentration gradients. The study was conceived as a series of methodological evaluations aimed at better understanding nanoparticle measurement devices and methods. lt focused on inhalation exposure to airborne particles, as respiration is considered to be the most important entrance pathway for nanoparticles in the body in terms of risk. The targeted survey (pilot study) was conducted as a feasibility study for a later nationwide survey on the handling of nanoparticles and the applications of specific protection means in industry. The study consisted of targeted phone interviews with health and safety officers of Swiss companies that were believed to use or produce nanoparticles. This was followed by a representative survey on the level of nanoparticle usage in Switzerland. lt was designed based on the results of the pilot study. The study was conducted among a representative selection of clients of the Swiss National Accident Insurance Fund (SUVA), covering about 85% of Swiss production companies. The third part of this thesis focused on the methods to measure nanoparticles. Several pre- studies were conducted studying the limits of commonly used measurement devices in the presence of nanoparticle agglomerates, This focus was chosen, because several discussions with users and producers of the measurement devices raised questions about their accuracy measuring nanoparticle agglomerates and because, at the same time, the two survey studies revealed that such powders are frequently used in industry. The first preparatory experiment focused on the accuracy of the scanning mobility particle sizer (SMPS), which showed an improbable size distribution when measuring powders of nanoparticle agglomerates. Furthermore, the thesis includes a series of smaller experiments that took a closer look at problems encountered with other measurement devices in the presence of nanoparticle agglomerates: condensation particle counters (CPC), portable aerosol spectrometer (PAS) a device to estimate the aerodynamic diameter, as well as diffusion size classifiers. Some initial feasibility tests for the efficiency of filter based sampling and subsequent counting of carbon nanotubes (CNT) were conducted last. The pilot study provided a detailed picture of the types and amounts of nanoparticles used and the knowledge of the health and safety experts in the companies. Considerable maximal quantities (> l'000 kg/year per company) of Ag, Al-Ox, Fe-Ox, SiO2, TiO2, and ZnO (mainly first generation particles) were declared by the contacted Swiss companies, The median quantity of handled nanoparticles, however, was 100 kg/year. The representative survey was conducted by contacting by post mail a representative selection of l '626 SUVA-clients (Swiss Accident Insurance Fund). It allowed estimation of the number of companies and workers dealing with nanoparticles in Switzerland. The extrapolation from the surveyed companies to all companies of the Swiss production sector suggested that l'309 workers (95%-confidence interval l'073 to l'545) of the Swiss production sector are potentially exposed to nanoparticles in 586 companies (145 to l'027). These numbers correspond to 0.08% (0.06% to 0.09%) of all workers and to 0.6% (0.2% to 1.1%) of companies in the Swiss production sector. To measure airborne concentrations of sub micrometre-sized particles, a few well known methods exist. However, it was unclear how well the different instruments perform in the presence of the often quite large agglomerates of nanostructured materials. The evaluation of devices and methods focused on nanoparticle agglomerate powders. lt allowed the identification of the following potential sources of inaccurate measurements at workplaces with considerable high concentrations of airborne agglomerates: - A standard SMPS showed bi-modal particle size distributions when measuring large nanoparticle agglomerates. - Differences in the range of a factor of a thousand were shown between diffusion size classifiers and CPC/SMPS. - The comparison between CPC/SMPS and portable aerosol Spectrometer (PAS) was much better, but depending on the concentration, size or type of the powders measured, the differences were still of a high order of magnitude - Specific difficulties and uncertainties in the assessment of workplaces were identified: the background particles can interact with particles created by a process, which make the handling of background concentration difficult. - Electric motors produce high numbers of nanoparticles and confound the measurement of the process-related exposure. Conclusion: The surveys showed that nanoparticles applications exist in many industrial sectors in Switzerland and that some companies already use high quantities of them. The representative survey demonstrated a low prevalence of nanoparticle usage in most branches of the Swiss industry and led to the conclusion that the introduction of applications using nanoparticles (especially outside industrial chemistry) is only beginning. Even though the number of potentially exposed workers was reportedly rather small, it nevertheless underscores the need for exposure assessments. Understanding exposure and how to measure it correctly is very important because the potential health effects of nanornaterials are not yet fully understood. The evaluation showed that many devices and methods of measuring nanoparticles need to be validated for nanoparticles agglomerates before large exposure assessment studies can begin. Zusammenfassung : Das Gesundheitsrisiko von Nanopartikel am Arbeitsplatz ist die Wahrscheinlichkeit dass ein Arbeitnehmer einen möglichen Gesundheitsschaden erleidet wenn er diesem Stoff ausgesetzt ist: sie wird gewöhnlich als Produkt von Schaden mal Exposition gerechnet. Für eine gründliche Abklärung möglicher Risiken von Nanomaterialien müssen also auf der einen Seite Informationen über die Freisetzung von solchen Materialien in die Umwelt vorhanden sein und auf der anderen Seite solche über die Exposition von Arbeitnehmenden. Viele dieser Informationen werden heute noch nicht systematisch gesarnmelt und felilen daher für Risikoanalysen, Die Doktorarbeit hatte als Ziel, die Grundlagen zu schaffen für eine quantitative Schatzung der Exposition gegenüber Nanopartikel am Arbeitsplatz und die Methoden zu evaluieren die zur Messung einer solchen Exposition nötig sind. Die Studie sollte untersuchen, in welchem Ausmass Nanopartikel bereits in der Schweizer Industrie eingesetzt werden, wie viele Arbeitnehrner damit potentiel] in Kontakt komrrien ob die Messtechnologie für die nötigen Arbeitsplatzbelastungsmessungen bereits genügt, Die Studie folcussierte dabei auf Exposition gegenüber luftgetragenen Partikel, weil die Atmung als Haupteintrittspforte iïlr Partikel in den Körper angesehen wird. Die Doktorarbeit besteht baut auf drei Phasen auf eine qualitative Umfrage (Pilotstudie), eine repräsentative, schweizerische Umfrage und mehrere technische Stndien welche dem spezitischen Verständnis der Mëglichkeiten und Grenzen einzelner Messgeräte und - teclmikeri dienen. Die qualitative Telephonumfrage wurde durchgeführt als Vorstudie zu einer nationalen und repräsentativen Umfrage in der Schweizer Industrie. Sie zielte auf Informationen ab zum Vorkommen von Nanopartikeln, und den angewendeten Schutzmassnahmen. Die Studie bestand aus gezielten Telefoninterviews mit Arbeit- und Gesundheitsfachpersonen von Schweizer Unternehmen. Die Untemehmen wurden aufgrund von offentlich zugànglichen lnformationen ausgewählt die darauf hinwiesen, dass sie mit Nanopartikeln umgehen. Der zweite Teil der Dolctorarbeit war die repräsentative Studie zur Evalniernng der Verbreitnng von Nanopaitikelanwendungen in der Schweizer lndustrie. Die Studie baute auf lnformationen der Pilotstudie auf und wurde mit einer repräsentativen Selektion von Firmen der Schweizerischen Unfall Versicherungsanstalt (SUVA) durchgeüihxt. Die Mehrheit der Schweizerischen Unternehmen im lndustrieselctor wurde damit abgedeckt. Der dritte Teil der Doktorarbeit fokussierte auf die Methodik zur Messung von Nanopartikeln. Mehrere Vorstudien wurden dnrchgefîihrt, um die Grenzen von oft eingesetzten Nanopartikelmessgeräten auszuloten, wenn sie grösseren Mengen von Nanopartikel Agglomeraten ausgesetzt messen sollen. Dieser F okns wurde ans zwei Gründen gewählt: weil mehrere Dislcussionen rnit Anwendem und auch dem Produzent der Messgeràte dort eine Schwachstelle vermuten liessen, welche Zweifel an der Genauigkeit der Messgeräte aufkommen liessen und weil in den zwei Umfragestudien ein häufiges Vorkommen von solchen Nanopartikel-Agglomeraten aufgezeigt wurde. i Als erstes widmete sich eine Vorstndie der Genauigkeit des Scanning Mobility Particle Sizer (SMPS). Dieses Messgerät zeigte in Präsenz von Nanopartikel Agglorneraten unsinnige bimodale Partikelgrössenverteilung an. Eine Serie von kurzen Experimenten folgte, welche sich auf andere Messgeräte und deren Probleme beim Messen von Nanopartikel-Agglomeraten konzentrierten. Der Condensation Particle Counter (CPC), der portable aerosol spectrometer (PAS), ein Gerät zur Schàtzung des aerodynamischen Durchniessers von Teilchen, sowie der Diffusion Size Classifier wurden getestet. Einige erste Machbarkeitstests zur Ermittlnng der Effizienz von tilterbasierter Messung von luftgetragenen Carbon Nanotubes (CNT) wnrden als letztes durchgeiührt. Die Pilotstudie hat ein detailliiertes Bild der Typen und Mengen von genutzten Nanopartikel in Schweizer Unternehmen geliefert, und hat den Stand des Wissens der interviewten Gesundheitsschntz und Sicherheitsfachleute aufgezeigt. Folgende Typen von Nanopaitikeln wurden von den kontaktierten Firmen als Maximalmengen angegeben (> 1'000 kg pro Jahr / Unternehrnen): Ag, Al-Ox, Fe-Ox, SiO2, TiO2, und ZnO (hauptsächlich Nanopartikel der ersten Generation). Die Quantitäten von eingesetzten Nanopartikeln waren stark verschieden mit einem ein Median von 100 kg pro Jahr. ln der quantitativen Fragebogenstudie wurden l'626 Unternehmen brieflich kontaktiert; allesamt Klienten der Schweizerischen Unfallversicherringsanstalt (SUVA). Die Resultate der Umfrage erlaubten eine Abschätzung der Anzahl von Unternehmen und Arbeiter, welche Nanopartikel in der Schweiz anwenden. Die Hochrechnung auf den Schweizer lndnstriesektor hat folgendes Bild ergeben: ln 586 Unternehmen (95% Vertrauensintervallz 145 bis 1'027 Unternehmen) sind 1'309 Arbeiter potentiell gegenüber Nanopartikel exponiert (95%-Vl: l'073 bis l'545). Diese Zahlen stehen für 0.6% der Schweizer Unternehmen (95%-Vl: 0.2% bis 1.1%) und 0.08% der Arbeiternehmerschaft (95%-V1: 0.06% bis 0.09%). Es gibt einige gut etablierte Technologien um die Luftkonzentration von Submikrometerpartikel zu messen. Es besteht jedoch Zweifel daran, inwiefern sich diese Technologien auch für die Messurrg von künstlich hergestellten Nanopartikeln verwenden lassen. Aus diesem Grund folcussierten die vorbereitenden Studien für die Arbeitsplatzbeurteilnngen auf die Messung von Pulverri, welche Nan0partike1-Agg10merate enthalten. Sie erlaubten die ldentifikation folgender rnöglicher Quellen von fehlerhaften Messungen an Arbeitsplätzen mit erhöhter Luft-K0nzentrati0n von Nanopartikel Agglomeratenz - Ein Standard SMPS zeigte eine unglaubwürdige bimodale Partikelgrössenverteilung wenn er grössere Nan0par'til<e1Agg10merate gemessen hat. - Grosse Unterschiede im Bereich von Faktor tausend wurden festgestellt zwischen einem Diffusion Size Classiîier und einigen CPC (beziehungsweise dem SMPS). - Die Unterschiede zwischen CPC/SMPS und dem PAS waren geringer, aber abhängig von Grosse oder Typ des gemessenen Pulvers waren sie dennoch in der Grössenordnung von einer guten Grössenordnung. - Spezifische Schwierigkeiten und Unsicherheiten im Bereich von Arbeitsplatzmessungen wurden identitiziert: Hintergrundpartikel können mit Partikeln interagieren die während einem Arbeitsprozess freigesetzt werden. Solche Interaktionen erschweren eine korrekte Einbettung der Hintergrunds-Partikel-Konzentration in die Messdaten. - Elektromotoren produzieren grosse Mengen von Nanopartikeln und können so die Messung der prozessbezogenen Exposition stören. Fazit: Die Umfragen zeigten, dass Nanopartikel bereits Realitàt sind in der Schweizer Industrie und dass einige Unternehmen bereits grosse Mengen davon einsetzen. Die repräsentative Umfrage hat diese explosive Nachricht jedoch etwas moderiert, indem sie aufgezeigt hat, dass die Zahl der Unternehmen in der gesamtschweizerischen Industrie relativ gering ist. In den meisten Branchen (vor allem ausserhalb der Chemischen Industrie) wurden wenig oder keine Anwendungen gefunden, was schliessen last, dass die Einführung dieser neuen Technologie erst am Anfang einer Entwicklung steht. Auch wenn die Zahl der potentiell exponierten Arbeiter immer noch relativ gering ist, so unterstreicht die Studie dennoch die Notwendigkeit von Expositionsmessungen an diesen Arbeitsplätzen. Kenntnisse um die Exposition und das Wissen, wie solche Exposition korrekt zu messen, sind sehr wichtig, vor allem weil die möglichen Auswirkungen auf die Gesundheit noch nicht völlig verstanden sind. Die Evaluation einiger Geräte und Methoden zeigte jedoch, dass hier noch Nachholbedarf herrscht. Bevor grössere Mess-Studien durgefîihrt werden können, müssen die Geräte und Methodem für den Einsatz mit Nanopartikel-Agglomeraten validiert werden.

Interét et limites de l'evaluation du risque de récidive d'actes illégaux dans les expertises psychiatriques [Benefits and limitation of the assessment of second offense risk in psychiatric expertise].

The legislatives evolutions imply an important recourse to the psychiatric expertise in order to evaluate the potential dangerousness of a subject. However, in spite of the development of techniques and tools for this evaluation, the dangerousness assessment of a subject is in practice extremely complex and discussed in the scientific literature. The evolution of the concept of dangerousness to the risk assessment involved a technicisation of this evaluation which should not make forget the limits of these tools and the need for restoring the subject, the meaning and the clinic in this evaluation.

Improvement of cardiovascular risk prediction: time to review current knowledge, debates, and fundamentals on how to assess test characteristics.

Cardiovascular risk assessment might be improved with the addition of emerging, new tests derived from atherosclerosis imaging, laboratory tests or functional tests. This article reviews relative risk, odds ratios, receiver-operating curves, posttest risk calculations based on likelihood ratios, the net reclassification improvement and integrated discrimination. This serves to determine whether a new test has an added clinical value on top of conventional risk testing and how this can be verified statistically. Two clinically meaningful examples serve to illustrate novel approaches. This work serves as a review and basic work for the development of new guidelines on cardiovascular risk prediction, taking into account emerging tests, to be proposed by members of the 'Taskforce on Vascular Risk Prediction' under the auspices of the Working Group 'Swiss Atherosclerosis' of the Swiss Society of Cardiology in the future.

Assessing the associations between mental disorders, cardiovascular risk factors, and cardiovascular disease : the CoLaus/PsyCoLaus study

Background: Cardio-vascular diseases (CVD), their well established risk factors (CVRF) and mental disorders are common and co-occur more frequently than would be expected by chance. However, the pathogenic mechanisms and course determinants of both CVD and mental disorders have only been partially identified.Methods/Design: Comprehensive follow-up of CVRF and CVD with a psychiatric exam in all subjects who participated in the baseline cross-sectional CoLaus study (2003-2006) (n=6'738) which also included a comprehensive genetic assessment. The somatic investigation will include a shortened questionnaire on CVRF, CV events and new CVD since baseline and measurements of the same clinical and biological variables as at baseline. In addition, pro-inflammatory markers, persistent pain and sleep patterns and disorders will be assessed. In the case of a new CV event, detailed information will be abstracted from medical records. Similarly, data on the cause of death will be collected from the Swiss National Death Registry. The comprehensive psychiatric investigation of the CoLaus/PsyCoLaus study will use contemporary epidemiological methods including semi-structured diagnostic interviews, experienced clinical interviewers, standardized diagnostic criteria including threshold according to DSM-IV and sub-threshold syndromes and supplementary information on risk and protective factors for disorders. In addition, screening for objective cognitive impairment will be performed in participants older than 65 years.Discussion: The combined CoLaus/PsyCoLaus sample provides a unique opportunity to obtain prospective data on the interplay between CVRF/CVD and mental disorders, overcoming limitations of previous research by bringing together a comprehensive investigation of both CVRF and mental disorders as well as a large number of biological variables and a genome-wide genetic assessment in participants recruited from the general population.

A road map toward a globally harmonized approach for occupational health surveillance and epidemiology in nanomaterial workers

OBJECTIVE: Few epidemiological studies have addressed the health of workers exposed to novel manufactured nanomaterials. The small current workforce will necessitate pooling international cohorts. METHOD: A road map was defined for a globally harmonized framework for the careful choice of materials, exposure characterization, identification of study populations, definition of health endpoints, evaluation of appropriateness of study designs, data collection and analysis, and interpretation of the results. RESULTS: We propose a road map to reach global consensus on these issues. The proposed strategy should ensure that the costs of action are not disproportionate to the potential benefits and that the approach is pragmatic and practical. CONCLUSIONS: We should aim to go beyond the collection of health complaints, illness statistics, or even counts of deaths; the manifestation of such clear endpoints would indicate a failure of preventive measures.

Missed appointments in an outpatient clinic for adolescents, an approach to predict the risk of missing.

PURPOSE: To predict the risk of an adolescent patient to miss an appointment, based on the previous appointments and on the characteristics of the patient and the appointment. METHODS: Two thousand one hundred ninety-three (1873 females) patients aged 12 to 20 years having scheduled at least four appointments were included. We assessed the rate of missed nonexcused appointments of each patient. Second, a Markovian multilevel model was used to predict the risk of defaulting. RESULTS: Forty-five percent of the patients have not missed even once, and 14% of females and 17% of males have missed &gt;25% of their appointments. Females show two types of behaviors (an abstract concept that groups individuals based on a combination of their appointment-keeping and their recorded type of healthcare need) depending on the diagnosis. Somatic, gynecology, violence, and counseling diagnoses are mostly grouped together. In this group, having already missed and having an appointment with a paramedical provider increases the risk of missing. In the second group (eating disorders and psychiatric diagnoses) having already missed and a longer delay between appointments influence the risk of missing, although the risk is lower for this latter group. Males only show one type of behavior regarding missed appointments. Having missed a previous appointment, being older, having cancelled the next to last appointment and the type of diagnosis explain the risk of missing. CONCLUSIONS: Patients who have already defaulted have a higher risk of defaulting again. Means of control regarding missed appointments should consequently focus on defaulters, to decrease the associated workload. Reminders could be a solution for the follow-up appointments scheduled with a long delay.