Development of an optimized methodology for tensile testing of carbon steels in hydrogen environment

The study was performed at OCAS, the Steel Research Centre of ArcelorMittal for the Industry market. The major aim of this research was to obtain an optimized tensile testing methodology with in-situ H-charging to reveal the hydrogen embrittlement in various high strength steels. The second aim of this study has been the mechanical characterization of the hydrogen effect on hight strength carbon steels with varying microstructure, i.e. ferrite-martensite and ferrite-bainite grades. The optimal parameters for H-charging - which influence the tensile test results (sample geometry type of electrolyte, charging methods effect of steel type, etc.) - were defined and applied to Slow Strain Rate testing, Incremental Step Loading and Constant Load Testing. To better understand the initiation and propagation of cracks during tensile testing with in-situ H-charging, and to make the correlation with crystallographic orientation, some materials have been analyzed in the SEM in combination with the EBSD technique. The introduction of a notch on the tensile samples permits to reach a significantly improved reproducibility of the results. Comparing the various steel grades reveals that Dual Phase (ferrite-martensite) steels are more sensitive to hydrogen induced cracking than the FB (ferritic-bainitic) ones. This higher sensitivity to hydrogen was found back in the reduced failure times, increased creep rates and enhanced crack initiation (SEM) for the Dual Phase steels in comparison with the FB steels.

Failure mechanism under tensile loads in CFRP 0-90º cross-ply laminates containing voids

The failure mechanism of a voided CFRP 0-90° cross-ply laminate under tensile loads applied in one direction was studied in this Final Degree Project. For this purpose, voided coupons were manufactured for being tested and a FEA was done. In both investigations, voids were placed in 90º and 0º direction, in order to understand the void location influence. On the one hand, the behaviour of the voided laminates was investigated through a FEM in order to preview the stress distribution within the material. On the other hand, voided specimens where manufactured by applying blowing agent in between the inner layers. These specimens were tested by a quasi-static step wise tensile test where data showing its real behaviour was collected. Specimens were X-rayed after each step of the test in order to investigate the failure mechanism of the composite. Data from the test was studied so that relations such as strength of the laminates, crack density per stress, void length per first crack at the void and void area per first crack at the specimen could be characterized

Testing Cayley graph densities

We present a computer-assisted analysis of combinatorial properties of the Cayley graphs of certain finitely generated groups: Given a group with a finite set of generators, we study the density of the corresponding Cayley graph, that is, the least upper bound for the average vertex degree (= number of adjacent edges) of any finite subgraph. It is known that an m-generated group is amenable if and only if the density of the corresponding Cayley graph equals to 2m. We test amenable and non-amenable groups, and also groups for which amenability is unknown. In the latter class we focus on Richard Thompson’s group F.

Testing the entrepreneurial intention model on a two-country sample

This paper tests the Entrepreneurial Intention Model -which is adapted from the Theory of Planned Behavior- on a sample of 533 individuals from two quite different countries: one of them European (Spain) and the other South Asian (Taiwan). A newly developed Entrepreneurial Intention Questionnaire (EIQ) has being used which tries to overcome some of the limitations of previous instruments. Structural equations techniques were used in the empirical analysis. Results are generally satisfactory, indicating that the model is probably adequate for studying entrepreneurship. Support for the model was found not only in the combined sample, but also in each of the national ones. However, some differences arose that may indicate demographic variables contribute differently to the formation of perceptions in each culture.

Testing of stair climbing point-of-choice prompts in Barcelona at an outdoor set of stairs and scalators on the Montjuïc site

Regular stair climbing has well-documented health dividends, such as increased fitness and strength, weight loss and reduced body fat, improved lipid profiles and reduced risk of osteoporosis. The general absence of barriers to participation makes stair climbing an ideal physical activity (PA) for health promotion. Studies in the US and the UK have consistently shown that interventions to increase the accumulation of lifestyle PA by climbing stairs rather than using the escalators are effective. However, there are no previous in Catalonia. This project tested one message for their ability to prompt travelers on the Montjuïc site to choose the stairs rather than the escalator when climbing up the Monjuïc hill. One standard message, " Take the stairs! 7 minutes of stair climbing a day protects your heart" provided a comparison with previous research done in the UK. Translated into Catalan and Spanish, it was presented on a poster positioned at the point of choice between the stairs and the escalator. The study used a quasi-experimental, interrupted time series design. Travelers, during several and specific hours on two days of the week, were coded for stair or escalator use, gender, age, ethnic status, presence of accompanying children or bags by one observer. Overall, the intervention resulted in a 81% increase in stair climbing. In the follow-up period without messages, stair climbing dropped out to baseline levels. This preliminary study showed a significant effect on stair use. However, caution is needed since results are based on a small sample and, only a low percentage of the sample took the stairs at baseline or the intervention phase . Future research on stair use in Catalonia should focus on using bigger samples, different sites (metro stations, airports, shopping centers, etc) , different messages and techniques to promote stair climbing.

Testing for poverty dominance: an application to Canada

The paper proposes and applies statistical tests for poverty dominance that check for whether poverty comparisons can be made robustly over ranges of poverty lines and classes of poverty indices. This helps provide both normative and statistical confidence in establishing poverty rankings across distributions. The tests, which can take into account the complex sampling procedures that are typically used by statistical agencies to generate household-level surveys, are implemented using the Canadian Survey of Labour and Income Dynamics (SLID) for 1996, 1999 and 2002. Although the yearly cumulative distribution functions cross at the lower tails of the distributions, the more recent years tend to dominate earlier years for a relatively wide range of poverty lines. Failing to take into account SLID's sampling variability (as is sometimes done) can inflate significantly one's confidence in ranking poverty. Taking into account SLID's complex sampling design (as has not been done before) can also decrease substantially the range of poverty lines over which a poverty ranking can be inferred.

Testing low-altitude infrared digital photography from a mini-UAV to retrieve information for biological conservation

Satellite remote sensing imagery is used for forestry, conservation and environmental applications, but insufficient spatial resolution, and, in particular, unavailability of images at the precise timing required for a given application, often prevent achieving a fully operational stage. Airborne remote sensing has the advantage of custom-tuned sensors, resolution and timing, but its price prevents using it as a routine technique for the mentioned fields. Some Unmanned Aerial Vehicles might provide a “third way” solution as low-cost techniques for acquiring remotely sensed information, under close control of the end-user, albeit at the expense of lower quality instrumentation and instability. This report evaluates a light remote sensing system based on a remotely-controlled mini-UAV (ATMOS-3) equipped with a color infra-red camera (VEGCAM-1) designed and operated by CATUAV. We conducted a testing mission over a Mediterranean landscape dominated by an evergreen woodland of Aleppo pine (Pinus halepensis) and (Holm) oak (Quercus ilex) in the Montseny National Park (Catalonia, NE Spain). We took advantage of state-of-the-art ortho-rectified digital aerial imagery (acquired by the Institut Cartogràfic de Catalunya over the area during the previous year) and used it as quality reference. In particular, we paid attention to: 1) Operationality of flight and image acquisition according to a previously defined plan; 2) Radiometric and geometric quality of the images; and 3) Operational use of the images in the context of applications. We conclude that the system has achieved an operational stage regarding flight activities, although with meteorological limits set by wind speed and turbulence. Appropriate landing areas can be sometimes limiting also, but the system is able to land on small and relatively rough terrains such as patches of grassland or short matorral, and we have operated the UAV as far as 7 km from the control unit. Radiometric quality is sufficient for interactive analysis, but probably insufficient for automated processing. A forthcoming camera is supposed to greatly improve radiometric quality and consistency. Conventional GPS positioning through time synchronization provides coarse orientation of the images, with no roll information.

Testing, not modelling, the impact of cohesion support: a theoretical framework and some preliminary results for the Spanish regions

This paper develops a simple model that can be used to estimate the effectiveness of Cohesion expenditure relative to similar but unsubsidized projects, thereby making it possible to explicitly test an important assumption that is often implicit in estimates of the impact of Cohesion policies. Some preliminary results are reported for the case of infrastructure investment in the Spanish regions.

Testing for sufficient information in structural VARs

We derive necessary and sufficient conditions under which a set of variables is informationally sufficient, i.e. it contains enough information to estimate the structural shocks with a VAR model. Based on such conditions, we suggest a procedure to test for informational sufficiency. Moreover, we show how to amend the VAR if informational sufficiency is rejected. We apply our procedure to a VAR including TFP, unemployment and per-capita hours worked. We find that the three variables are not informationally sufficient. When adding missing information, the effects of technology shocks change dramatically.

Automatización de testing

El objetivo del proyecto es el desarrollo de una herramienta de trabajo para un departamento de Calidad. A través de ella, se deben poder ejecutar unos test automatizados sobre unas funcionalidades que tiene la aplicación Logic Class: el Cálculo de Nómina y Seguros Sociales.

Testing Delivery Systems in Transnational virtual learning: the vocational management training for the european tourism industry (VocMat) case study

This article discusses the lessons learned from developing and delivering the Vocational Management Training for the European Tourism Industry (VocMat) online training programme, which was aimed at providing flexible, online distance learning for the European tourism industry. The programme was designed to address managers ‘need for flexible, senior management level training which they could access at a time and place which fitted in with their working and non-work commitments. The authors present two main approaches to using the Virtual Learning Environment, the feedback from the participants, and the implications of online Technology in extending tourism training opportunities

Compositional hypotheses of subcompositional stability and specific perturbation change and their testing

In standard multivariate statistical analysis common hypotheses of interest concern changes in mean vectors and subvectors. In compositional data analysis it is now well established that compositional change is most readily described in terms of the simplicial operation of perturbation and that subcompositions replace the marginal concept of subvectors. To motivate the statistical developments of this paper we present two challenging compositional problems from food production processes.Against this background the relevance of perturbations and subcompositions can beclearly seen. Moreover we can identify a number of hypotheses of interest involvingthe specification of particular perturbations or differences between perturbations and also hypotheses of subcompositional stability. We identify the two problems as being the counterpart of the analysis of paired comparison or split plot experiments and of separate sample comparative experiments in the jargon of standard multivariate analysis. We then develop appropriate estimation and testing procedures for a complete lattice of relevant compositional hypotheses

Mean intrinsic tensile properties of stone groundwood fibers from softwood

Stone groundwood (SGW) is a fibrous matter commonly prepared in a high yield process, and mainly used for papermaking applications. In this work, the use of SGW fibers is explored as reinforcing element of polypropylene (PP) composites. Due to its chemical and superficial features, the use of coupling agents is needed for a good adhesion and stress transfer across the fiber-matrix interface. The intrinsic strength of the reinforcement is a key parameter to predict the mechanical properties of the composite and to perform an interface analysis. The main objective of the present work was the determination of the intrinsic tensile strength of stone groundwood fibers. Coupled and non-coupled PP composites from stone groundwood fibers were prepared. The influence of the surface morphology and the quality at interface on the final properties of the composite was analyzed and compared to that of fiberglass PP composites. The intrinsic tensile properties of stone groundwood fibers, as well as the fiber orientation factor and the interfacial shear strength of the current composites were determined

Tensile strength characteristics of polypropylene composites reinforced with stone groundwood fibers from softwood

The behavior of stone groundwood / polypropylene injection-molded composites was evaluated with and without coupling agent. Stone groundwood (SGW) is a fibrous material commonly prepared in a high yield process and mainly used for papermaking applications. In this work, the use of SGW fibers was explored as a reinforcing element of polypropylene (PP) composites. The surface charge density of the composite components was evaluated, as well as the fiber’s length and diameter inside the composite material. Two mixing extrusion processes were evaluated, and the use of a kinetic mixer, instead of an internal mixer, resulted in longer mean fiber lengths of the reinforcing fibers. On the other hand, the accessibility of surface hydroxyl groups of stone groundwood fibers was improved by treating the fibers with 5% of sodium hydroxide, resulting in a noticeable increase of the tensile strength of the composites, for a similar percentage of coupling agent. A new parameter called Fiber Tensile Strength Factor is defined and used as a baseline for the comparison of the properties of the different composite materials. Finally the competitiveness of stone groundwood / polypropylene / polypropylene-co-maleic anhydride system, which compared favorably to sized glass-fiber / polypropylene GF/PP and glass-fiber / polypropylene / polypropylene-co-maleic anhydride composite formulations, was quantified by means of the fiber tensile strength factor