Irrigation performance and gross water productivity in furrow-irrigated ornamental tree production

In the ornamental plant production region of Girona (Spain), which is one of the largest of its kind in southern Europe, most of the surface is irrigated using wide blocked-end furrows. The objectives of this paper were: (1) to evaluate the irrigation scheduling methods used by ornamental plant producers; (2) to analyse different scenarios inorder to assess how they affect irrigation performance; (3) to evaluate the risk of deep percolation; and (4) to calculategross water productivity. A two-year study in a representative commercial field, planted with Prunus cerasifera ‘Nigra’, was carried out. The irrigation dose applied by the farmers was slightly smaller than the required water dose estimated by the use of two different methods: the first based on soil water content, and the second based on evapotranspiration. Distribution uniformity and application efficiency were high, with mean values above 87%. Soil water contentmeasurements revealed that even at the end of the furrow, where the infiltrated water depth was greatest, more than 90% of the infiltrated water was retained in the shallowest 40 cm of the soil; accordingly, the risk of water loss due to deep percolation was minimal. Gross water productivity for ornamental tree production was € 11.70 m–3, approximately 20 times higher than that obtained with maize in the same region

An approach to costs and energy consumption in private urban Spanish Mediterranean landscapes from a simplified model in sprinkle irrigation

The number of private gardens has increased in recent years, creating a more pleasant urban model, but not without having an environmental impact, including increased energy consumption, which is the focus of this study. The estimation of costs and energy consumption for the generic typology of private urban gardens is based on two simplifying assumptions: square geometry with surface areas from 25 to 500 m2 and hydraulic design with a single pipe. In total, eight sprinkler models have been considered, along with their possible working pressures, and 31 pumping units grouped into 5 series that adequately cover the range of required flow rates and pressures, resultin in 495 hydraulic designs repeated for two climatically different locations in the Spanish Mediterranean area (Girona and Elche). Mean total irrigation costs for the locality with lower water needs (Girona) and greater needs (Elche) were € 2,974 ha-¹ yr-¹ and € 3,383 ha-¹ yr-¹, respectively. Energy costs accounted for 11.4% of the total cost for the first location, and 23.0% for the second. While a suitable choice of the hydraulic elements of the setup is essential, as it may provide average energy savings of 77%, due to the low energy cost in relation to the cost of installation, the potential energy savings do not constitute a significant incentive for the irrigation system design. The low efficiency of the pumping units used in this type of garden is the biggest obstacle and constraint to achieving a high quality energy solution

Comparison between land suitability and actual crop distribution in an irrigation district of the Ebro valley (Spain)

El objetivo de la presente investigación fue analizar la correspondencia entre los resultados de una evaluación de tierras con la distribución real de los cultivos. Para ello la aptitud biofísica de las tierras se comparó con diferentes tipologías de frecuencia de ocurrencia de los cultivos y rotaciones derivadas de mapas de cultivos multitemporales. La investigación fue llevada a cabo en el distrito de riego de Flumen (33.000 ha), localizado en el valle del Ebro (NE España). La evaluación de tierras se basó en una cartografía de suelos 1:100.000, según el esquema FAO, para los principales cultivos presentes en el área de estudio (alfalfa, cereales de invierno, maíz, arroz y girasol). Se utilizaron tres mapas de frecuencia de cultivos y un mapa de rotaciones, derivado de una serie temporal de imágenes Landsat TM y ETM+ del periodo 1993-2000, y se compararon con los mapas de aptitud de tierras para los diferentes cultivos. Se analizó estadísticamente (Pearson χ2, Cramer V, Gamma y Somers D) la relación entre los dos tipos de variables. Los resultados muestran la existencia de una relación significativa (P=0,001) entre la localización de los cultivos y la idoneidad de las tierras, excepto de cultivos oportunistas como el girasol, muy influenciado por las subvenciones en el periodo estudiado. Las rotaciones basadas en la alfalfa muestran los mayores porcentajes (52%) de ocupación en las tierras más aptas para la agricultura en el área de estudio. El presente enfoque multitemporal de análisis de la información ofrece una visión más real que la comparación entre un mapa de evaluación de tierras y un mapa de cultivos de una fecha determinada, cuando se valora el grado de acuerdo entre las recomendaciones sobre la aptitud de las tierras y los cultivos realmente cultivados por los agricultores.

Irrigation performance and gross water productivity in furrow-irrigated ornamental tree production

In the ornamental plant production region of Girona (Spain), which is one of the largest of its kind in southern Europe, most of the surface is irrigated using wide blocked-end furrows. The objectives of this paper were: (1) to evaluate the irrigation scheduling methods used by ornamental plant producers; (2) to analyse different scenarios in order to assess how they affect irrigation performance; (3) to evaluate the risk of deep percolation; and (4) to calculate gross water productivity. A two-year study in a representative commercial field, planted with Prunus cerasifera ‘Nigra’, was carried out. The irrigation dose applied by the farmers was slightly smaller than the required water dose estimated by the use of two different methods: the first based on soil water content, and the second based on evapotranspiration. Distribution uniformity and application eff iciency were high, with mean values above 87%. Soil water content measurements revealed that even at the end of the furrow, where the infiltrated water depth was greatest, more than 90% of the infiltrated water was retained in the shallowest 40 cm of the soil; accordingly, the risk of water loss due to deep percolation was minimal. Gross water productivity for ornamental tree production was € 11.70 m–3, approximately 20 times higher than that obtained with maize in the same region.

Evaluation of markets for irrigation water in the internal river basins of Catalonia, Spain

Irrigated agriculture has come under close scrutiny in Europe recently because of its high share of total water consumption and its apparent inefficiency. Several water policies have been advocated, in particular the use of economic instruments such as water markets. This paper simulates the impact of a policy based upon water markets on agricultural production in the internal river basins of Catalonia (Spain). This zone presents certain particularities that make it very interesting to study: competition between sectors for the resource (agriculture-urban consumption-recreational uses), recent periods of resource insufficiency and conflicts between irrigators as a result of the measures taken by the hydraulic administration in drought situations. The results show that these markets would guarantee an optimal reassignment of the resource in situations of supply restrictions, and although compared to the situation without markets they would not mean higher economic profits for the irrigators, they could prevent conflicts between them. Nevertheless, doubts exist about their acceptance by irrigators

Effect of dripline flushing on subsurface drip irrigation systems

The velocity of dripline flushing in subsurface drip irrigation (SDI) systems affects system design, cost, management, performance, and longevity. A 30‐day field study was conducted at Kansas State University to analyze the effect of four targeted flushing velocities (0.23, 0.30, 0.46, and 0.61 m/s) for a fixed 15 min duration of flushing and three flushing frequencies (no flushing or flushing every 15 or 30 days) on SDI emitter discharge and sediments within the dripline and removed in the flushing water. At the end of the field experiment (371 h), the amount of solids carried away by the flushing water and retained in every lateral were determined as well as laboratory determination of emitter discharge for every single emitter within each dripline. Greater dripline flushing velocities, which also resulted in greater flushing volumes, tended to result in greater amounts of solids in the flushing water, but the differences were not always statistically significant. Neither the frequency of flushing nor the interaction of flushing frequency and velocity significantly affected the amount of solids in the flushing water. There was a greater concentration of solids in the beginning one‐third of the 90 m laterals, particularly for treatments with no flushing or with slower dripline flushing velocities. As flushing velocity and concurrently flushing volume increased, there was a tendency for greater solids removal and/or more equal distribution within the dripline. At the end of the field study, the average emitter discharge as measured in the laboratory for a total of 3970 emitters was 0.64 L/h. which was significantly less (approximately 2.5%) than the discharge for new and unused emitters. Only six emitters were nearly or fully clogged, with discharges between 0% and 5% of new and unused emitters. Flushing velocity and flushing frequency did not have consistent significant effects on emitter discharge, and those numerical differences that did exist were small (<3%). Emitter discharge was approximately 3% less for the distal ends of the driplines (last 20% of the dripline). Although not a specific factor in the study, the results of solids removals during flushing and solids retention within the different dripline sections suggest that duration of flushing may be a more cost‐effective management option than increasing the dripline flushing velocity through SDI system design. Finally, although microirrigation system components have been improved over the years, the need for flushing to remove solids and reduce clogging potential has not been eliminated

Photocatalytic Activity of Nanostructured Anatase Coatings Obtained by Cold Gas Spray

This article describes a photocatalytic nanostructured anatase coating deposited by cold gas spray (CGS)supported on titanium sub-oxide (TiO22x) coatings obtained by atmospheric plasma spray (APS) onto stainless steel cylinders. The photocatalytic coating was homogeneous and preserved the composition and nanostructure of the starting powder. The inner titanium sub-oxide coating favored the deposition of anatase particles in the solid state. Agglomerated nano-TiO2 particles fragmented when impacting onto the hard surface of the APS TiO22x bond coat. The rough surface provided by APS provided an ideal scenario for entrapping the nanostructured particles, which may be adhered onto the bond coat due to chemical bonding; a possible bonding mechanism is described. Photocatalytic experiments showed that CGS nano-TiO2 coating was active for photodegrading phenol and formic acid under aqueous conditions. The results were similar to the performance obtained by competitor technologies and materials such as dip-coating P25 photocatalysts. Disparity in the final performance of the photoactive materials may have been caused by differences in grain size and the crystalline composition of titanium dioxide.

Subsurface drip irrigation emitter spacing effects on soil water redistribution, corn yield and water productivity

Emitter spacings of 0.3 to 0.6 m are commonly used for subsurface drip irrigation (SDI) of corn on the deep, silt loam soils of the U.S. Great Plains. Subsurface drip irrigation emitter spacings of 0.3, 0.6, 0.9 and 1.2 m were examined for the resulting differences in soil water redistribution, corn grain yield, yield components, seasonal water use, and water productivity in a 4‐year field study (2005 through 2008) at the Kansas State University Northwest Research‐Extension Center, Colby, Kansas. The results indicate that there is increased preferential water movement along the dripline (parallel) as compared to perpendicular to the dripline and that this phenomenon partially compensates for wider emitter spacings in terms of soil water redistribution. Corn yield and water productivity (WP) were not significantly affected by the emitter spacing with application of a full irrigation regime

Private micro-irrigation costs using reclaimed water

The cost of reusing water in micro-irrigation at the field level has not been studied in depth although the use of effluents in agriculture is a viable alternative in areas where water is scarce or there is intense competition for its use. The aim of the present study is to analyse the private costs of water reuse in micro-irrigation in an experimental plot. This analysis is intended to provide information about the decision a farmer would make when the choice to use conventional or reclaimed water is guided by cost criteria. The components of the total costs of different combinations of four types of filters and five emitters that can be installed in micro-irrigation systems using reclaimed water have been studied with the data obtained from an experimental plot in conditions similar to those of fruit orchards. Different scenarios that compared the costs of using conventional or reclaimed water in terms of water price and nutrient content were also studied. The results show that a proper combination of filters and emitters can save up to 33% in irrigation costs. Capital costs and maintenance costs were the most variable among the different combinations. Scenario analysis showed that the greater price of reclaimed water could be compensated by high nutrient contents, which would reduce fertilizer costs

Natura i història en la creació dels "paisatges de l'aigua" a la plana de l'Alt Empordà

L’objectiu d’aquest article és fer una aproximació al procés històric de creació dels anomenats “paisatges de l’aigua” a la plana de l’Alt Empordà. En primer lloc, es presenten els principals elements que configuren els paisatges de l’aigua a la plana (els rius, les rieres, els aiguamolls, els estanys, les sèquies, canals de regadiu, etc.). A continuació, s’analitza el procés històric de creació dels paisatges de l’aigua a la plana de l’Alt Empordà a través d’un discurs que s’ha simplificat en dues grans etapes: una llarga etapa caracteritzada per la lluita mantinguda per la societat altempordanesa contra l’aigua i, una segona etapa, molt més recent, on els esforços d’aquesta societat es concentren en l’obtenció d’aquesta aigua. Per últim, s’analitza en detall aquest procés a partir del cas concret del paisatge configurat per les closes

Projecte de reg per degoteig en una plantació de 5,25 ha de vinya a Can Macià (T.M. d’Òdena, comarca de l’Anoia)

Estudi sobre la instal.lació d’un sistema de reg per degoteig i un sistema de fertirrigació a 5,25 ha de vinya amb les corrresponents instal.lacions necessàries per a un adequat funcionament per tal d’augmentar la rendibilitat de la varietat Chardonnay, garantint de la manera més constant possible, una òptima qualitat de producció per tal d’ aconseguir un marge de seguretat més gran davant les possibles pèrdues de qualitat que es podrien originar per les condicions climàtiques adverses

Instal·lacions d'una nau magatzem per a un club de golf i automatització del seu reg

El projecte efectua la descripció i càlcul de les instal·lacions d'una nau magatzem per a un club de golf, així com l’automatització del reg i adobament de la gespa per tal d’optimitzar els recursos hídrics. La part de les instal·lacions s’ha separat en cinc blocs en els quals s’ha efectuat una descripció de les característiques de les diferents instal·lacions, el càlcul de línies elèctriques, dimensionament dels equips, col·lectors i distàncies, complint els objectius inicials i la reglamentació vigent. Pel que fa l’automatització del procés, s’han complert els objectius d’optimitzar els recursos hídrics de què disposava el club, aprofitant al màxim les aigües pluvials recollides i permetent la fertilització de la gespa, de manera homogènia a tot el camp

Ecologia del tram final del riu Ebre: la comunitat de macròfits i macroinvertebrats associats

Durant els últims anys al tram final del riu Ebre s’han produit canvis molt importants a l’ecosistema fluvial: l’augment de la transparència de l’aigua ha comportat una proliferació massiva de macròfits que ha provocat canvis en l’estructura tròfica i en la composició de les comunitats biològiques, representant un greu perill per espècies amenaçades com Margaritifera auricularia. A més del problema ecològic, els macròfits estan provocant molts problemes socio-econòmics perjudicant les captacions d’aigua (centrals nuclears, hidroelèctriques i regadius), creant problemes per a la navegació fluvial, i afavorint la proliferació d’espècies molestes com la mosca negra (Simulium erythrocephalum). Entre les diferents causes que podrien explicar aquests canvis en l’ecosistema hi ha: la disminució del fòsfor dissolt, la regularització i la disminució de cabals, i l’aparició d’espècies introduides com el musclo zebra. Segurament es tractarà d’un efecte combinat de les diferents causes però és necessari analitzar-les per tal de conèixer quines tenen més incidència i així, poder proposar mesures de gestió per als problemes ecològics que pateix el tram final de l’Ebre. Al present projecte de tesi (inclós en el projecte d’I+D: efectes de la millora de la qualitat de l'aigua i de l'alteració del règim de cabals sobre les comunitats biològiques del tram final del riu Ebre) s’estudiarà la comunitat de macròfits i macroinvertebrats associats per tal de determinar el paper que tenen en el canvis que s’han produit al riu durant els últims anys.

Avaluació de la substitució del plasma de sang per farina de rovell d’ou com a font proteica en l’alimentació de garrins en l’etapa de desmamament.

Els subproductes de l’ou, es presenten com a una alternativa viable a l’SDPP (Spray Dried Porcine Plasma),principalment per l’elevada qualitat de la seva proteïna, alhora que representen una fontimportant d’energia i agents antimicrobians, així com de vitamines i minerals. A més,el cost que suposa la seva inclusió en alimentació garrina és inferior al del plasma i coma element afegit, es donaria sortida a les elevades quantitats de subproductes de l’ougenerades cada any, no aptes per al consum humà