Towards closure between measured and modelled UV under clear skies at four diverse sites

The purpose of this work is determine the extent of closure between measurements and models of UV irradiances at diverse sites using state of the art instruments, models, and the best available data as inputs to the models. These include information about aerosol optical depth (unfortunately not extending down as far into the UVB region as desirable because such information is not generally available), ozone column amounts, as well as vertical profiles of temperature. We concentrate on clear-sky irradiances, and report the results in terms of UV Index (UVI)

Using a Parameterization of a Radiative Transfer Model to Build High-Resolution Maps of Typical Clear-Sky UV Index in Catalonia, Spain

To perform a climatic analysis of the annual UV index (UVI) variations in Catalonia, Spain (northeast of the Iberian Peninsula), a new simple parameterization scheme is presented based on a multilayer radiative transfer model. The parameterization performs fast UVI calculations for a wide range of cloudless and snow-free situations and can be applied anywhere. The following parameters are considered: solar zenith angle, total ozone column, altitude, aerosol optical depth, and single-scattering albedo. A sensitivity analysis is presented to justify this choice with special attention to aerosol information. Comparisons with the base model show good agreement, most of all for the most common cases, giving an absolute error within 0.2 in the UVI for a wide range of cases considered. Two tests are done to show the performance of the parameterization against UVI measurements. One uses data from a high-quality spectroradiometer from Lauder, New Zealand [45.04°S, 169.684°E, 370 m above mean sea level (MSL)], where there is a low presence of aerosols. The other uses data from a Robertson–Berger-type meter from Girona, Spain (41.97°N, 2.82°E, 100 m MSL), where there is more aerosol load and where it has been possible to study the effect of aerosol information on the model versus measurement comparison. The parameterization is applied to a climatic analysis of the annual UVI variation in Catalonia, showing the contributions of solar zenith angle, ozone, and aerosols. High-resolution seasonal maps of typical UV index values in Catalonia are presented

Long-range transport of Saharan dust to northern Europe: The 11-16 October 2001 outbreak observed with EARLINET

The spread of mineral particles over southwestern, western, and central Europeresulting from a strong Saharan dust outbreak in October 2001 was observed at10 stations of the European Aerosol Research Lidar Network (EARLINET). For the firsttime, an optically dense desert dust plume over Europe was characterized coherentlywith high vertical resolution on a continental scale. The main layer was located abovethe boundary layer (above 1-km height above sea level (asl)) up to 3–5-km height, andtraces of dust particles reached heights of 7–8 km. The particle optical depth typicallyranged from 0.1 to 0.5 above 1-km height asl at the wavelength of 532 nm, andmaximum values close to 0.8 were found over northern Germany. The lidar observationsare in qualitative agreement with values of optical depth derived from Total OzoneMapping Spectrometer (TOMS) data. Ten-day backward trajectories clearly indicated theSahara as the source region of the particles and revealed that the dust layer observed,e.g., over Belsk, Poland, crossed the EARLINET site Aberystwyth, UK, and southernScandinavia 24–48 hours before. Lidar-derived particle depolarization ratios,backscatter- and extinction-related A ° ngstro¨m exponents, and extinction-to-backscatterratios mainly ranged from 15 to 25%, 0.5 to 0.5, and 40–80 sr, respectively, within thelofted dust plumes. A few atmospheric model calculations are presented showing the dustconcentration over Europe. The simulations were found to be consistent with thenetwork observations.

Estudi de la influència del lubricant en operacions de mecanització

Els processos de mecanitzat amb arrencament de ferritja consisteixen en arrencar contínuament petits fragments de material de la peça a la que es vol donar forma mitjançant les eines de tall. En treballar amb metalls, aquestes forces de tall són importants, i provoquen el desgast de les eines així com un escalfament important de l’eina i la peça. Per aquest motiu s’introdueixen els olis de tall, amb les principals funcions de refrigerar i lubricar. Tradicionalment, aquests olis de tall s’han subministrat a raig, quedant la zona de treball inundada. Els últims anys, degut a les millores tecnològiques i per intentar estalviar amb olis de tall, s’ha ideat un nou sistema anomenat mínima quantitat de lubricant, el qual subministra petites gotes d’oli, no soluble en aigua, dins un flux d’aire a pressió. Aquest sistema, a més, s’injecta prop de la zona de treball, on és estricament necessari. Aquest sistema redueix considerablement el consum d’oli de tall, i a més, augmenta l’eficiència de lalubricació. A part, elimina els posteriors tractaments per reciclar l’oli de tall un cop perd les seves propietats. Per aquest motiu, es pretén estudiar la utilització d’un mètode semblant al de la mínima quantitat de lubricant, subministrant el mateix oli de tall que s’utilitza convencionalment però polvoritzar per tal de convertir-lo en un aerosol