Síntesi de nanopartícules de TiO2 fàcilment processables i el seu ús per a fabricar a baixa temperatura cel·les solars sensibilitzades

La gran demanda energètica i la problemàtica dels combustibles fòssils i d‟altres recursos per a obtenir energia posen de manifest la necessitat de desenvolupar tecnologies netes, sostenibles i econòmicament viables de generació d‟energia. En aquest àmbit, les cel·les solars sensibilitzades amb colorant (Dye Sensitized Solar Cells, DSSC), que transformen l‟energia solar a energia elèctrica, són una solució factible. A més, el desenvolupament de mètodes per a construir aquestes cel·les a baixa temperatura permetria fabricar-les sobre substrats plàstics, fet que els donaria un valor afegit i permetria una producció en continu, ràpida i amb baix cost tant, econòmic, com d‟impacte ambiental. Aquest treball presenta el desenvolupament d‟un mètode de producció a baixa temperatura (140 ºC) de DSSC, amb eficiència de 5,9 % sobre substrats FTO/vidre. Aquest valor és superior a la majoria de les eficiències reportades a la bibliografia de DSSC construïdes a baixa temperatura. Les capes mesoporoses que formen els elèctrodes de les DCCS es dipositen per doctor blade a partir d‟una pasta composta per nanopartícules de TiO2, de 4-8 nm, recobertes d‟àcid 3,6,9-trioxadecanoic, per nanopartícules de Degussa P25, de 20-25 nm, i com a dissolvents només s‟utilitza aigua i etanol. L‟aplicació d‟un tractament a 140 ºC permet eliminar la matèria orgànica de la superfície de les nanopartícules de 4-8 nm i unir-les a les de Degussa P25. Aquest fet permet obtenir capes mesoporoses sinteritzades de 6 μm de gruix. A més, l‟aplicació d‟un post-tractament, en el qual s‟utilitza l‟àcid hexafluoro titànic (IV), produeix un lleuger increment en l‟eficiència. Endemés, l‟obtenció de capes primes de TiO2 sobre substrats plàstics és un tema d‟actualitat a causa de la falta de mètodes de deposició a baixa temperatura. En aquest context, s‟ha sintetitzat, mitjançant processos respectuosos amb el medi ambient nanopartícules de TiO2 cristal·lí modificades superficialment amb lauril gal·lat i àcid 3,6,9-trioxodecanoic. Les nanopartícules poden ser dispersades en dissolvents orgànics i aigua respectivament, fet que permet obtenir suspensions estables i de fàcil manipulació. Aquestes poden ser utilitzades com a precursores per a obtenir capes primes a baixa temperatura de TiO2 cristal·lí. En concret, les capes primes formades per nanopartícules de TiO2 modificades amb àcid 3,6,9-trioxodecanoic s‟han utilitzat com a blocking layer en les DSSC construïdes a baixa temperatura.

Analysis of the role of mobility-lifetime products in the performance of amorphous silicon p-i-n solar cells

An analytical model of an amorphous silicon p-i-n solar cell is presented to describe its photovoltaic behavior under short-circuit conditions. It has been developed from the analysis of numerical simulation results. These results reproduce the experimental illumination dependence of short-circuit resistance, which is the reciprocal slope of the I(V) curve at the short-circuit point. The recombination rate profiles show that recombination in the regions of charged defects near the p-i and i-n interfaces should not be overlooked. Based on the interpretation of the numerical solutions, we deduce analytical expressions for the recombination current and short-circuit resistance. These expressions are given as a function of an effective ¿¿ product, which depends on the intensity of illumination. We also study the effect of surface recombination with simple expressions that describe its influence on current loss and short-circuit resistance.

Spectral analysis of the angular distribution function of back reflectors for thin film silicon solar cells

Nowadays, one of the most important challenges to enhance the efficiency of thin film silicon solar cells is to increase the short circuit intensity by means of optical confinement methods, such as textured back-reflector structures. In this work, two possible textured structures to be used as back reflectors for n-i-p solar cells have been optically analyzed and compared to a smooth one by using a system which is able to measure the angular distribution function (ADF) of the scattered light in a wide spectral range (350-1000 nm). The accurate analysis of the ADF data corresponding to the reflector structures and to the μc-Si:H films deposited onto them allows the optical losses due to the reflector absorption and its effectiveness in increasing light absorption in the μc-Si:H layer, mainly at long wavelengths, to be quantified.

Optimization of KOH etching process to obtain textured substrates suitable for heterojunction solar cells fabricated by HWCVD

In this work, we have studied the texturization process of (100) c-Si wafers using a low concentration potassium hydroxide solution in order to obtain good quality textured wafers. The optimization of the etching conditions have led to random but uniform pyramidal structures with good optical properties. Then, symmetric heterojunctions were deposited by Hot-Wire CVD onto these substrates and the Quasi-Steady-State PhotoConductance technique was used to measure passivation quality. Little degradation in the effective lifetime and implicit open circuit voltage of these devices (< 20 mV) was observed in all cases. It is especially remarkable that for big uniform pyramids, the open-circuit voltage is comparable to the values obtained on flat substrates.

Optical analysis of textured plastic substrates to be used in thin silicon solar cells

Light confinement strategies in thin-film silicon solar cells play a crucial role in the performance of the devices. In this work, the possible use of Ag-coated stamped polymers as reflectors to be used in n-i-p solar cells is studied. Different random roughnesses (nanometer and micrometer size) have been transferred on poly(methylmethacrylate) (PMMA) by hot embossing. Morphological and optical analyses of masters, stamped polymers and reflectors have been carried out evidencing a positive surface transference on the polymer and the viability of a further application in solar cells.

Progress in single junction microcrystalline silicon solar cells deposited by Hot-Wire CVD

Hot-Wire Chemical Vapor Deposition has led to microcrystalline silicon solar cell efficiencies similar to those obtained with Plasma Enhanced CVD. The light-induced degradation behavior of microcrystalline silicon solar cells critically depends on the properties of their active layer. In the regime close to the transition to amorphous growth (around 60% of amorphous volume fraction), cells incorporating an intrinsic layer with slightly higher crystalline fraction and [220] preferential orientation are stable after more than 7000 h of AM1.5 light soaking. On the contrary, solar cells whose intrinsic layer has a slightly lower crystalline fraction and random or [111] preferential orientation exhibit clear light-induced degradation effects. A revision of the efficiencies of Hot-Wire deposited microcrystalline silicon solar cells is presented and the potential efficiency of this technology is also evaluated.

Control of doped layers in p-i-n microcrystalline solar cells fully deposited with HWCVD

In this paper, the influence of the deposition conditions on the performance of p-i-n microcrystalline silicon solar cells completely deposited by hot-wire chemical vapor deposition is studied. With this aim, the role of the doping concentration, the substrate temperature of the p-type layer and of amorphous silicon buffer layers between the p/i and i/n microcrystalline layers is investigated. Best results are found when the p-type layer is deposited at a substrate temperature of 125 °C. The dependence seen of the cell performance on the thickness of the i layer evidenced that the efficiency of our devices is still limited by the recombination within this layer, which is probably due to the charge of donor centers most likely related to oxygen.

Amorphous silicon thin film solar cells deposited entirely by Hot-Wire Chemical Vapour Deposition at low temperature (<150 ºC)

Amorphous silicon n-i-p solar cells have been fabricated entirely by Hot-Wire Chemical Vapour Deposition (HW-CVD) at low process temperature < 150 °C. A textured-Ag/ZnO back reflector deposited on Corning 1737F by rf magnetron sputtering was used as the substrate. Doped layers with very good conductivity and a very less defective intrinsic a-Si:H layer were used for the cell fabrication. A double n-layer (μc-Si:H/a-Si:H) and μc-Si:H p-layer were used for the cell. In this paper, we report the characterization of these layers and the integration of these layers in a solar cell fabricated at low temperature. An initial efficiency of 4.62% has been achieved for the n-i-p cell deposited at temperatures below 150 °C over glass/Ag/ZnO textured back reflector.

Muntatge i caracterització d'una placa DSSC: Buscant potència

Treball de recerca realitzat per alumnes d'ensenyament secundari i guardonat amb un Premi CIRIT per fomentar l'esperit científic del Jovent l'any 2009. Els objectius inicials foren la construcció d una 'Cèl•lula Solar Sensibilitzada mitjançant un Colorant’ (DSSC) amb el tint d una col llombarda i posterior caracterització segons el dossier 'Nanocrystalline Solar Cell Kit: Recreating Photosynthesis’. Les DSSC (Dye Sensitized Solar Cell) són un tipus de cèl•lules que imiten els principis que la fotosíntesis ha fet servir exitosament durant més de 3,5 bilions d anys. S’han construït algunes DSSC i se n’ha provat la seva eficiència. El seu funcionament es basa en l’energia d’un fotó que excita un electró i el fa saltar de nivell energètic fins que es desprèn de l’àtom de colorant, deixant un forat en la molècula. Aquest electró lliure passa a través de la capa de TiO2 fins arribar a la càrrega on es genera el corrent elèctric. Tot seguit, l’electró arriba al contra-elèctrode i és aquí on entra en contacte amb l’electròlit, el mediador iode/triiode. Aquest regenera l’electró, que anteriorment ha saltat del colorant, oxidant-se ell mateix.

L'energia solar fotovoltaica

Treball de recerca realitzat per alumnes d'ensenyament secundari i guardonat amb un Premi CIRIT per fomentar l'esperit cientí­fic del Jovent l'any 2009. Després d'una breu introducció sobre l'energia solar, l'estudi analitza quin és el procés de fabricació que se segueix per fer les plaques solars fotovoltaiques policristal·lines i monocristal·lines i quin és el seu funcionament. És a dir, com és possible obtenir energia elèctrica gràcies a la llum del Sol. També es descriuen les instal·lacions autònomes i les connectades a la xarxa, així com els elements que les integren. S'inclou, a més, un punt explicant quins són els factors que condicionen l'obtenció d'energia i els avenços més recents en aquest camp de la tecnologia. Per finalitzar la part teòrica, s'analitza una instal·lació fotovoltaica situada a Cervera i la seva producció. Pel que fa al treball de camp, es va construir un seguidor solar.

PEN as substrate for new solar cell technologies

The possible use of polyethylene naphthalate as substrate for low-temperature deposited solar cells has been studied in this paper. The transparency of this polymer makes it a candidate to be used in both substrate and superstrate configurations. ZnO:Al has been deposited at room temperature on top of PEN. The resulting structure PEN/ZnO:Al presented good optical and electrical properties. PEN has been successfully textured (nanometer and micrometer random roughness) using hot-embossing lithography. Reflector structures have been built depositing Ag and ZnO:Al on top of the stamped polymer. The deposition of these layers did not affect the final roughness of the whole. The reflector structure has been morphologically and optically analysed to verify its suitability to be used in solar cells.

Analysis of S-rich CuIn(S,Se)2 layers for photovoltaic applications: Influence of the sulfurization temperature on the crystalline properties of electrodeposited and sulfurized CuInSe2 precursors

This paper reports the microstructural analysis of S-rich CuIn(S,Se)2 layers produced by electrodeposition of CuInSe2 precursors and annealing under sulfurizing conditions as a function of the temperature of sulfurization. The characterization of the layers by Raman scattering, scanning electron microscopy, Auger electron spectroscopy, and XRD techniques has allowed observation of the strong dependence of the crystalline quality of these layers on the sulfurization temperature: Higher sulfurization temperatures lead to films with improved crystallinity, larger average grain size, and lower density of structural defects. However, it also favors the formation of a thicker MoS2 interphase layer between the CuInS2 absorber layer and the Mo back contact. Decreasing the temperature of sulfurization leads to a significant decrease in the thickness of this intermediate layer and is also accompanied by significant changes in the composition of the interface region between the absorber and the MoS2 layer, which becomes Cu rich. The characterization of devices fabricated with these absorbers corroborates the significant impact of all these features on device parameters as the open circuit voltage and fill factor that determine the efficiency of the solar cells.

Microstructure and secondary phases in coevaporated CuInS2 films: Dependence on growth temperature and chemical composition

The microstructure of CuInS2-(CIS2) polycrystalline films deposited onto Mo-coated glass has been analyzed by Raman scattering, Auger electron spectroscopy (AES), transmission electron microscopy, and x-ray diffraction techniques. Samples were obtained by a coevaporation procedure that allows different Cu-to-In composition ratios (from Cu-rich to Cu-poor films). Films were grown at different temperatures between 370 and 520-°C. The combination of micro-Raman and AES techniques onto Ar+-sputtered samples has allowed us to identify the main secondary phases from Cu-poor films such as CuIn5S8 (at the central region of the layer) and MoS2 (at the CIS2/Mo interface). For Cu-rich films, secondary phases are CuS at the surface of as-grown layers and MoS2 at the CIS2/Mo interface. The lower intensity of the MoS2 modes from the Raman spectra measured at these samples suggests excess Cu to inhibit MoS2 interface formation. Decreasing the temperature of deposition to 420-°C leads to an inhibition in observing these secondary phases. This inhibition is also accompanied by a significant broadening and blueshift of the main A1 Raman mode from CIS2, as well as by an increase in the contribution of an additional mode at about 305 cm-1. The experimental data suggest that these effects are related to a decrease in structural quality of the CIS2 films obtained under low-temperature deposition conditions, which are likely connected to the inhibition in the measured spectra of secondary-phase vibrational modes.

Silicon nanocrystals as an enabling material for silicon Ppotonics

Silicon nanocrystals (Si-nc) is an enabling material for silicon photonics, which is no longer an emerging field of research but an available technology with the first commercial products available on the market. In this paper, properties and applications of Si-nc in silicon photonics are reviewed. After a brief history of silicon photonics, the limitations of silicon as a light emitter are discussed and the strategies to overcome them are briefly treated, with particular attention to the recent achievements. Emphasis is given to the visible optical gain properties of Si-nc and to its sensitization effect on Er ions to achieve infrared light amplification. The state of the art of Si-nc applied in a few photonic components is reviewed and discussed. The possibility to exploit Si-nc for solar cells is also presented. in addition, nonlinear optical effects, which enable fast all-optical switches, are described.