Micro-Raman study of stress distribution in local isolation structures and correlation with transmission electron microscopy

Stress in local isolation structures is studied by micro‐Raman spectroscopy. The results are correlated with predictions of an analytical model for the stress distribution and with cross‐sectional transmission electron microscopy observations. The measurements are performed on structures on which the Si3N4 oxidation mask is still present. The influence of the pitch of the periodic local isolation pattern, consisting of parallel lines, the thickness of the mask, and the length of the bird"s beak on the stress distribution are studied. It is found that compressive stress is present in the Si substrate under the center of the oxidation mask lines, with a magnitude dependent on the width of the lines. Large tensile stress is concentrated under the bird"s beak and is found to increase with decreasing length of the bird"s beak and with increasing thickness of the Si3N4 film.

Premartensitic and martensitic phase transitions in ferromagnetic Ni2MnGa

We present an experimental study of the premartensitic and martensitic phase transitions in a Ni2MnGa single crystal by using ultrasonic techniques. The effect of applied magnetic field and uniaxial compressive stress has been investigated. It has been found that they substantially modify the elastic and magnetic behavior of the alloy. These experimental findings are a consequence of magnetoelastic effects. The measured magnetic and vibrational behavior agrees with the predictions of a recently proposed Landau-type model [A. Planes et al., Phys. Rev. Lett. 79, 3926 (1997)] that incorporates a magnetoelastic coupling as a key ingredient.

Microstructure of highly oriented, hexagonal, boron nitride thin films grown on crystalline silicon by radio frequency plasma-assisted chemical vapor deposition

We present a high‐resolution electron microscopy study of the microstructure of boron nitride thin films grown on silicon (100) by radio‐frequency plasma‐assisted chemical vapor deposition using B2H6 (1% in H2) and NH3 gases. Well‐adhered boron nitride films grown on the grounded electrode show a highly oriented hexagonal structure with the c‐axis parallel to the substrate surface throughout the film, without any interfacial amorphous layer. We ascribed this textured growth to an etching effect of atomic hydrogen present in the gas discharge. In contrast, films grown on the powered electrode, with compressive stress induced by ion bombardment, show a multilayered structure as observed by other authors, composed of an amorphous layer, a hexagonal layer with the c‐axis parallel to the substrate surface and another layer oriented at random

Ultraviolet optical and microstructural properties of MgF2 and LaF3 coatings deposited by ion-beam sputtering and boat and electron-beam evaporation

Single layers of MgF2 and LaF3 were deposited upon superpolished fused-silica and CaF2 substrates by ion-beam sputtering (IBS) as well as by boat and electron beam (e-beam) evaporation and were characterized by a variety of complementary analytical techniques. Besides undergoing photometric and ellipsometric inspection, the samples were investigated at 193 and 633 nm by an optical scatter measurement facility. The structural properties were assessed with atomic-force microscopy, x-ray diffraction, TEM techniques that involved conventional thinning methods for the layers. For measurement of mechanical stress in the coatings, special silicon substrates were coated and analyzed. The dispersion behavior of both deposition materials, which was determined on the basis of various independent photometric measurements and data reduction techniques, is in good agreement with that published in the literature and with the bulk properties of the materials. The refractive indices of the MgF2 coatings ranged from 1.415 to 1.440 for the wavelength of the ArF excimer laser (193 nm) and from 1.435 to 1.465 for the wavelength of the F2 excimer laser (157 nm). For single layers of LaF3 the refractive indices extended from 1.67 to 1.70 at 193 nm to ~1.80 at 157 nm. The IBS process achieves the best homogeneity and the lowest surface roughness values (close to 1 nmrms) of the processes compared in the joint experiment. In contrast to MgF2 boat and e-beam evaporated coatings, which exhibit tensile mechanical stress ranging from 300 to 400 MPa, IBS coatings exhibit high compressive stress of as much as 910 MPa. A similar tendency was found for coating stress in LaF3 single layers. Experimental results are discussed with respect to the microstructural and compositional properties as well as to the surface topography of the coatings.

Plasma-enhanced chemical vapor deposition of boron nitride thin films from B2H6-H2-NH3 and B2H6-N2 gas mixtures

Highly transparent and stoichiometric boron nitride (BN) films were deposited on both electrodes (anode and cathode) of a radio-frequency parallel-plate plasma reactor by the glow discharge decomposition of two gas mixtures: B2H6-H2-NH3 and B2H6-N2. The chemical, optical, and structural properties of the films, as well as their stability under long exposition to humid atmosphere, were analyzed by x-ray photoelectron, infrared, and Raman spectroscopies; scanning and transmission electron microscopies; and optical transmittance spectrophotometry. It was found that the BN films grown on the anode using the B2H6-H2-NH3 mixture were smooth, dense, adhered well to substrates, and had a textured hexagonal structure with the basal planes perpendicular to the film surface. These films were chemically stable to moisture, even after an exposition period of two years. In contrast, the films grown on the anode from the B2H6-N2 mixture showed tensile stress failure and were very unstable in the presence of moisture. However, the films grown on the cathode from B2H6-H2-NH3 gases suffered from compressive stress failure on exposure to air; whereas with B2H6-N2 gases, adherent and stable cathodic BN films were obtained with the same crystallographic texture as anodic films prepared from the B2H6-H2-NH3 mixture. These results are discussed in terms of the origin of film stress, the effects of ion bombardment on the growing films, and the surface chemical effects of hydrogen atoms present in the gas discharge.

Premartensitic and martensitic phase transition in ferromagnetic Ni2MnGa

We present an experimental study of the premartensitic and martensitic phase transitions in a Ni2MnGa single crystal by using ultrasonic techniques. The effect of applied magnetic field and uniaxial compressive stress has been investigated. It has been found that they substantially modify the elastic and magnetic behavior of the alloy. These experimental findings are a consequence of magnetoelastic effects. The measured magnetic and vibrational behavior agrees with the predictions of a recently proposed Landau-type model [A. Planes et al., Phys. Rev. Lett. 79, 3926 (1997)] that incorporates a magnetoelastic coupling as a key ingredient.

Perioperative stress in dogs underwent elective surgery: evaluation of the antioxidant activity

Projecte de recerca elaborat a partir d’una estada al Department of Biological Science a la University of Lincoln, a la Gran Bretanya, entre octubre i desembre del 2006. L'objectiu del present assaig va ser desciure les respostes antioxidants d'estrès en gossos sotmesos a cirurgia electiva, en condicions de pràctica clínica normals, durant les fases de preoperatori i postoperatori.Setze gossos van ser sotmesos a orquiectomia o ovariohisterectomia electives, utilitzant un protocol quirúrgic estàndard. Durant les fases preoperatoria i postoperatoria, cada animal va ser confinat a la Unitat de Cures Intensives, temps durant el qual es va estudiar la seva resposta antioxidant. Els valors obtinguts a diferents temps van ser comparats amb el valor basal, que s'havia obtingut del mateix animal estant aquest en el seu ambient habitual. No es van detectar variacions significants causades per l'estrès perioperatori. Els valors màxims es van observar durant la fase preoperatoria, just després que l'animal fós confinat a la Unitat de Cures Intensives, moment en el que l'estrès percebut era degut a les amenaces psicològiques de una àrea restringida i de la manipulació per persones desonegudes. L'abscència de variacions significants podrien ser degudes al sistema i el temps d'emmagatzement de les mostres. En humana s'han descrit les alteracions en l'activitat dels antioxidants sèrics després d'un mes d'emmagatzematent. Per definir l'estabilitat, després de la recollida de mostres, de l'activitat dels antioxidants en sèrum de gos és necessari realitzar més estudis.

Assaigs Stress Corrosion Cracking (SCC)

En aquest projecte es presenta la realització d’un sistema d’assaig de la corrosió sota tensió (stress corrosion cracking, SCC) i un estudi de l’efecte de l’SCC sobre dos acers d’eina per matrius d’estampació en calent. L’SCC és la formació i propagació d’esquerdes en un material degut a la interacció de tres factors: un medi corrosiu, un material susceptible i una tensió estàtica aplicada. Aquestes esquerdes són difícils de detectar i poden provocar fallades catastròfiques inesperades i, en concret, s’ha detectat aquest fenomen en matrius refrigerades d’estampació en calent. Es pretén dissenyar i construir un dispositiu d’assaig SCC per tal d’utilitzar-lo per l’estudi dels materials 1.2367 i 1.2343 en condicions d’aigua de xarxa, aigua destil·lada i inhibidor. Aquests assaigs es realitzen a les temperatures de 40 i 80ºC ja que un estudi previ ha simulat les condicions de temperatura als canals de refrigeració de les matrius d’estampació en calent i s’ha vist que aquestes són les temperatures assolides. La raó d’estudiar aquests materials és perquè són dos acers d’eina per treball en calent convencionals, usats en l’àmbit de les matrius refrigerades d’estampació en calent i en general en processos de conformat en calent (forja, moldeig). S’estudia el comportament a tracció d’aquests materials en aquestes condicions comparant-lo amb el mateix assaig però en condicions en aire, i s’avaluen les diferències en la tensió màxima, la ductilitat, el mecanisme de fractura o l’esquerdament sofert. Es fa un estudi fractogràfic de les mostres mitjançant microscòpia electrònica de rastreig (SEM) i un estudi de les superfícies laterals i del secondary cracking mitjançant microscòpia òptica. Es comparen els diferents resultats obtinguts i es determina en quines condicions s’ha desenvolupat SCC i en quines no, en quina intensitat i quines opcions hi ha per evitar-lo.

Monetary policy rules and financial stress: does financial instability matter for monetary

We examine whether and how main central banks responded to episodes of financial stress over the last three decades. We employ a new methodology for monetary policy rules estimation, which allows for time-varying response coefficients as well as corrects for endogeneity. This flexible framework applied to the U.S., U.K., Australia, Canada and Sweden together with a new financial stress dataset developed by the International Monetary Fund allows not only testing whether the central banks responded to financial stress but also detects the periods and type of stress that were the most worrying for monetary authorities and to quantify the intensity of policy response. Our findings suggest that central banks often change policy

Simulador de rendimiento Stress Tester

Desarrollo de una aplicación para la empresa CCSAgresso, con el objetivo de evaluar el rendimiento en una máquina, mediante los datos aportados por pruebas de simulación. Cada prueba de simulación está contenida en un fichero de texto, cuya lectura y almacenamiento en la base de datos son la base de la aplicación. Los objetivos son poder introducir, actualizar, gestionar y mostrar esos valores de la base de datos con una aplicación sencilla, intuitiva y que realice todas las operaciones que necesita el usuario.

Mesophyll conductance to CO2 and leaf morphological characteristics under drought stress during Quercus ilex L resprouting

• Quercus ilex L., the dominant species in Mediterranean forests and one with a great capacity for resprouting after disturbances, is threatened by the expected increase in fire frequency and drought associated with climate change. • The aim of this study was to determine the contribution of photosynthesis limitants, especially mesophyll conductance (gmes ) during this species’ resprouting and under summer drought. • Resprouts showed 5.3-fold increased gmes and 3.8-fold increased stomatal conductance (gs) atmidday with respect to leaves of undisturbed individuals. With increased drought, structural changes (decreased density and increased thickness) in resprouts contributed to the observed higher photosynthesis and increased gmes. However, gmes only partially depended on leaf structure, and was also under physiological control. Resprouts also showed lower non-stomatal limitations (around 50% higher carboxylation velocity (Vc,max) and capacity for ribulose-1,5-bisphosphate regeneration (Jmax)). A significant contribution of gmes to leaf carbon isotope discrimination values was observed. • gmes exhibits a dominant role in photosynthesis limitation in Q. ilex and is regulated by factors other than morphology. During resprouting after disturbances, greater capacity to withstand drought, as evidenced by higher gmes , gs and lower non-stomatal limitants, enables increased photosynthesis and rapid growth.

Teleost fish larvae adapt to dietary arachidonic acid supply through modulation of the expression of lipid metabolism and stress response genes

Dietary fatty acid supply can affect stress response in fish during early development. Although knowledge on the mechanisms involved in fatty acid regulation of stress tolerance is scarce, it has often been hypothesised that eicosanoid profiles can influence cortisol production. Genomic cortisol actions are mediated by cytosolic receptors which may respond to cellular fatty acid signalling. An experiment was designed to test the effects of feeding gilthead sea-bream larvae with four microdiets, containing graded arachidonic acid (ARA) levels (0·4, 0·8, 1·5 and 3·0 %), on the expression of genes involved in stress response (steroidogenic acute regulatory protein, glucocorticoid receptor and phosphoenolpyruvate carboxykinase), lipid and, particularly, eicosanoid metabolism (hormone-sensitive lipase, PPARα, phospholipase A2, cyclo-oxygenase-2 and 5-lipoxygenase), as determined by real-time quantitative PCR. Fish fatty acid phenotypes reflected dietary fatty acid profiles. Growth performance, survival after acute stress and similar whole-body basal cortisol levels suggested that sea-bream larvae could tolerate a wide range of dietary ARA levels. Transcription of all genes analysed was significantly reduced at dietary ARA levels above 0·4 %. Nonetheless, despite practical suppression of phospholipase A2 transcription, higher leukotriene B4 levels were detected in larvae fed 3·0 % ARA, whereas a similar trend was observed regarding PGE2 production. The present study demonstrates that adaptation to a wide range of dietary ARA levels in gilthead sea-bream larvae involves the modulation of the expression of genes related to eicosanoid synthesis, lipid metabolism and stress response. The roles of ARA, other polyunsaturates and eicosanoids as signals in this process are discussed.

The relationships of stress, health and wellbeing among workers

The precise relationship between the positive psychological state of work (i.e. engagement ) and the negative psychological state (i.e. burnout) has recently received research attention. Some view these as opposite states on the same similar continuum, while others take the position that they represent different biobehavioral spheres. This study expands our knowledge of the phenomenta engagement and burnout by analyzing their separate and joint manifestations. Using a sample of 2094 nurses, respondents were analyzed to determine the configuration of antecedents leading to separate and joint states of engagement and burnout, the configuration of engagement and burnout leading to mental, physical and organizational outcomes, and the relationship between engagement, bornout, and risk of metabolic syndrome. The study found that while both work engagement and burnout are highly correlated to health and organizational outcomes, the relative statistical power of burnout has a greater direct effect on health. It is important for workers and managers to adress the sources of burnout before addressing the positive psychological aspects of worker engagement.

Role of Particle Shape on the Stress Propagation in Granular Packings

We present an experimental and numerical study on the influence that particle aspect ratio has on the mechanical and structural properties of granular packings. For grains with maximal symmetry (squares), the stress propagation in the packing localizes forming chainlike forces analogous to the ones observed for spherical grains. This scenario can be understood in terms of stochastic models of aggregation and random multiplicative processes. As the grains elongate, the stress propagation is strongly affected. The interparticle normal force distribution tends toward a Gaussian, and, correspondingly, the force chains spread leading to a more uniform stress distribution reminiscent of the hydrostatic profiles known for standard liquids