A fully automated hot-wall multiplasma-monochamber reactor for thin film deposition

We present a study on the development and the evaluation of a fully automated radio-frequency glow discharge system devoted to the deposition of amorphous thin film semiconductors and insulators. The following aspects were carefully addressed in the design of the reactor: (1) cross contamination by dopants and unstable gases, (2) capability of a fully automated operation, (3) precise control of the discharge parameters, particularly the substrate temperature, and (4) high chemical purity. The new reactor, named ARCAM, is a multiplasma-monochamber system consisting of three separated plasma chambers located inside the same isothermal vacuum vessel. Thus, the system benefits from the advantages of multichamber systems but keeps the simplicity and low cost of monochamber systems. The evaluation of the reactor performances showed that the oven-like structure combined with a differential dynamic pumping provides a high chemical purity in the deposition chamber. Moreover, the studies of the effects associated with the plasma recycling of material from the walls and of the thermal decomposition of diborane showed that the multiplasma-monochamber design is efficient for the production of abrupt interfaces in hydrogenated amorphous silicon (a-Si:H) based devices. Also, special attention was paid to the optimization of plasma conditions for the deposition of low density of states a-Si:H. Hence, we also present the results concerning the effects of the geometry, the substrate temperature, the radio frequency power and the silane pressure on the properties of the a-Si:H films. In particular, we found that a low density of states a-Si:H can be deposited at a wide range of substrate temperatures (100°C

Factor decomposition of spatial income inequality: a revision

Duro and Esteban (1998) proposed an additive decomposition of Theil populationweighted index by four income multiplicative factors (in spatial contexts). This note makes some additional methodological points: first, it argues that interaction effects are taken into account in the factoral indexes although only in a fairly restrictive way. As a consequence, we suggest to rewrite the decomposition formula as a sum of strict Theil indexes plus the interactive terms; second, it might be instructive to aggregate some of the initial factors; third, this decomposition can be immediately extended to the between- and within-group components.

Regional decomposition of CO2 emissions in the world: a cluster analysis

The purpose of this paper is to study the possible differences among countries as CO2 emitters and to examine the underlying causes of these differences. The starting point of the analysis is the Kaya identity, which allows us to break down per capita emissions in four components: an index of carbon intensity, transformation efficiency, energy intensity and social wealth. Through a cluster analysis we have identified five groups of countries with different behavior according to these four factors. One significant finding is that these groups are stable for the period analyzed. This suggests that a study based on these components can characterize quite accurately the polluting behavior of individual countries, that is to say, the classification found in the analysis could be used in other studies which look to study the behavior of countries in terms of CO2 emissions in homogeneous groups. In this sense, it supposes an advance over the traditional regional or rich-poor countries classifications .

Regional income inequalities in Europe: an updated measurement and some decomposition results

In this paper well-known summary inequality indexes are used to explore interregional income inequalities in Europe. In particular, we mainly employ Theils’population-weighted index because of its appealing properties. Two decomposition analysis are applied. First, regional inequalities are decomposed by regional subgroups (countries). Second, intertemporal inequality changes are separated into income and population changes. The main results can be summarized as follows. First, data confirm a reduction in crossregional inequality during 1982-97. Second, this reduction is basically due to real convergence among countries. Third, currently the greater part of European interregional disparities is within-country by nature, which introduce an important challenge for the European policy. Fourth, inequality changes are due mainly to income variations, population changes playing a minor role.

Thermal tests on the LISA pathfinder engineering model

Report for the scientific sojourn carried out at Albert Einstein Institut in Germany, from April to July 2006.

An analysis of strategic paths through the decomposition of total factor productivity: the case of Spanish savings banks

The Spanish savings banks attracted quite a considerable amount of interest within the scientific arena, especially subsequent to the disappearance of the regulatory constraints during the second decade of the 1980s. Nonetheless, a lack of research identified with respect to mainstream paths given by strategic groups, and the analysis of the total factor productivity. Therefore, on the basis of the resource-based view of the firm and cluster analysis, we make use of changes in structure and performance ratios in order to identify the strategic groups extant in the sector. We attain a threeways division, which we link with different input-output specifications defining strategic paths. Consequently, on the basis of these three dissimilar approaches we compute and decompose a Hicks-Moorsteen total factor productivity index. Obtained results put forward an interesting interpretation under a multi-strategic approach, together with the setbacks of employing cluster analysis within a complex strategic environment. Moreover, we also propose an ex-post method of analysing the outcomes of the decomposed total factor productivity index that could be merged with non-traditional techniques of forming strategic groups, such as cognitive approaches.

Numerical simulation of combined heat transfer phenomena (conduction, convection, and radiation). Application to he optimisation of thermal systems

Thermal systems interchanging heat and mass by conduction, convection, radiation (solar and thermal ) occur in many engineering applications like energy storage by solar collectors, window glazing in buildings, refrigeration of plastic moulds, air handling units etc. Often these thermal systems are composed of various elements for example a building with wall, windows, rooms, etc. It would be of particular interest to have a modular thermal system which is formed by connecting different modules for the elements, flexibility to use and change models for individual elements, add or remove elements without changing the entire code. A numerical approach to handle the heat transfer and fluid flow in such systems helps in saving the full scale experiment time, cost and also aids optimisation of parameters of the system. In subsequent sections are presented a short summary of the work done until now on the orientation of the thesis in the field of numerical methods for heat transfer and fluid flow applications, the work in process and the future work.

Structural decomposition analysis and input-output subsystems: An application to Spanish CO2 emissions

Analysis of gas emissions by the input-output subsystem approach provides detailed insight into pollution generation in an economy. Structural decomposition analysis, on the other hand, identifies the factors behind the changes in key variables over time. Extending the input-output subsystem model to account for the changes in these variables reveals the channels by which environmental burdens are caused and transmitted throughout the production system. In this paper we propose a decomposition of the changes in the components of CO2 emissions captured by an input-output subsystems representation. The empirical application is for the Spanish service sector, and the economic and environmental data are for years 1990 and 2000. Our results show that services increased their CO2 emissions mainly because of a rise in emissions generated by non-services to cover the final demand for services. In all service activities, the decomposed effects show an increase in CO2 emissions due to a decrease in emission coefficients (i.e., emissions per unit of output) compensated by an increase in emissions caused both by the input-output coefficients and the rise in demand for services. Finally, large asymmetries exist not only in the quantitative changes in the CO2 emissions of the various services but also in the decomposed effects of these changes. Keywords: structural decomposition analysis, input-output subsystems, CO2 emissions, service sector.

Improving the accuracy of heat balance integral methods applied to thermal problems with time dependent boundary conditions

In this paper the two main drawbacks of the heat balance integral methods are examined. Firstly we investigate the choice of approximating function. For a standard polynomial form it is shown that combining the Heat Balance and Refined Integral methods to determine the power of the highest order term will either lead to the same, or more often, greatly improved accuracy on standard methods. Secondly we examine thermal problems with a time-dependent boundary condition. In doing so we develop a logarithmic approximating function. This new function allows us to model moving peaks in the temperature profile, a feature that previous heat balance methods cannot capture. If the boundary temperature varies so that at some time t & 0 it equals the far-field temperature, then standard methods predict that the temperature is everywhere at this constant value. The new method predicts the correct behaviour. It is also shown that this function provides even more accurate results, when coupled with the new CIM, than the polynomial profile. Analysis primarily focuses on a specified constant boundary temperature and is then extended to constant flux, Newton cooling and time dependent boundary conditions.

Engineering the thermal emission of macroporous silicon

Todos los cuerpos emiten luz espontaneamente al ser calentados. El espectro de radiacion es una funcion de la temperatura y el material. Sin embargo, la mayoria de los materiales irradia, en general, en una banda espectral amplia. Algunas matereiales, por el contrario, son capaces de concentrar la radiacion termica en una banda espectral mucho mas estrecha. Estos materiales se conocen como emisores selectivos y su uso tiene un profundo impacto en la eficiencia de sistemas sistemas tales como iluminacion y conversion de energia termofotovoltaica. De los emisores selectivos se espera que sean capaces de operar a altas temperaturas y que emitan en una banda espectral muy concisa. Uno de los metodos mas prometedores para controlar y disenar el espectro de emision termico es la utilizacion de cristales fotonicos. Los cristales fotonicos son estructuras periodicas artificiales capaces de controlar y confinar la luz de formas sin precedentes. Sin embargo, la produccion de dichas estructuras con grandes superficies y capaces de soportar altas temperaturas sigue siendo una dificil tarea. Este trabajo esta dedicada al estudio de las propiedades de emision termica de estructuras 3D de silicio macroporoso en el rango espectral mid-IR (2-30 m). En particular, este trabajo se enfoca en reducir la elevada emisividad del silicio cristalino. Las muestras estudiadas en este trabajo tienen una periodicidad de 4 m, lo que limitan los resultados obtenidos a la banda del infrarrojo medio, aunque estructuras mucho mas pequenas son tecnologicamente realizables con el metodo de fabricacion utilizado. Hemos demostrado que el silicio macroporoso 3D puede inhibir completamente la emision termica en su superficie. Mas aun, esta banda se puede ajustar en un amplio margen mediante pequenos cambios durante la formacion de los macroporos. Tambien hemos demostrado que tanto el ancho como la frecuencia de la banda de inhibicion se puede doblar mediante la aplicacion de tecnicas de postprocesado adecuadas. Finalmente hemos mostrado que es posible crear bandas de baja emisividad arbitrariamente anchas mediante estructuras macroporosas aperiodicas.

Modeling of hybrid systems by piecewise decomposition

Piecewise linear models systems arise as mathematical models of systems in many practical applications, often from linearization for nonlinear systems. There are two main approaches of dealing with these systems according to their continuous or discrete-time aspects. We propose an approach which is based on the state transformation, more particularly the partition of the phase portrait in different regions where each subregion is modeled as a two-dimensional linear time invariant system. Then the Takagi-Sugeno model, which is a combination of local model is calculated. The simulation results show that the Alpha partition is well-suited for dealing with such a system

Stone-ground wood pulp-reinforced polypropylene composites: water uptake and thermal properties

Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC

The building blocks of international ecological footprint inequality: a regression-based decomposition

This paper performs an empirical Decomposition of International Inequality in Ecological Footprint in order to quantify to what extent explanatory variables such as a country’s affluence, economic structure, demographic characteristics, climate and technology contributed to international differences in terms of natural resource consumption during the period 1993-2007. We use a Regression-Based Inequality Decomposition approach. As a result, the methodology extends qualitatively the results obtained in standard environmental impact regressions as it comprehends further social dimensions of the Sustainable Development concept, i.e. equity within generations. The results obtained point to prioritizing policies that take into account both future and present generations.

Two complementary molecular energy decomposition schemes: the Mayer and Ziegler-Rauk methods in comparison

In the present paper we discuss and compare two different energy decomposition schemes: Mayer's Hartree-Fock energy decomposition into diatomic and monoatomic contributions [Chem. Phys. Lett. 382, 265 (2003)], and the Ziegler-Rauk dissociation energy decomposition [Inorg. Chem. 18, 1558 (1979)]. The Ziegler-Rauk scheme is based on a separation of a molecule into fragments, while Mayer's scheme can be used in the cases where a fragmentation of the system in clearly separable parts is not possible. In the Mayer scheme, the density of a free atom is deformed to give the one-atom Mulliken density that subsequently interacts to give rise to the diatomic interaction energy. We give a detailed analysis of the diatomic energy contributions in the Mayer scheme and a close look onto the one-atom Mulliken densities. The Mulliken density ρA has a single large maximum around the nuclear position of the atom A, but exhibits slightly negative values in the vicinity of neighboring atoms. The main connecting point between both analysis schemes is the electrostatic energy. Both decomposition schemes utilize the same electrostatic energy expression, but differ in how fragment densities are defined. In the Mayer scheme, the electrostatic component originates from the interaction of the Mulliken densities, while in the Ziegler-Rauk scheme, the undisturbed fragment densities interact. The values of the electrostatic energy resulting from the two schemes differ significantly but typically have the same order of magnitude. Both methods are useful and complementary since Mayer's decomposition focuses on the energy of the finally formed molecule, whereas the Ziegler-Rauk scheme describes the bond formation starting from undeformed fragment densities