Nano-electro-mechanical in dynamical cellular processes

Report for the scientific sojourn carried out at the Department of Structure and Constituents of Matter during 2007.The main focus of the work was on phenomena related to nano-electromechanical processes that take place on a cellular level. Additionally, it has also been performed independent work related to charge and energy transfer in bio molecules, energy transfer in coupled spin systems as well as electrodynamics of nonlinear metamaterials.

Investigations on doping of amorphous and nano-crystalline silicon films deposited by catalytic chemical vapour deposition

Hydrogenated amorphous and nanocrystalline silicon, deposited by catalytic chemical vapour deposition, have been doped during deposition by the addition of diborane and phosphine in the feed gas, with concentrations in the region of 1%. The crystalline fraction, dopant concentration and electrical properties of the films are studied. The nanocrystalline films exhibited a high doping efficiency, both for n and p doping, and electrical characteristics similar to those of plasma-deposited films. The doping efficiency of n-type amorphous silicon is similar to that obtained for plasma-deposited electronic-grade amorphous silicon, whereas p-type layers show a doping efficiency of one order of magnitude lower. A higher deposition temperature of 450°C was required to achieve p-type films with electrical characteristics similar to those of plasma-deposited films.

Characterization of nano-oxide layers fabricated by ion beam oxidation

In this paper, a remote O2 ion source is used for the formation of nano-oxide layers. The oxidation efficiency was measured in CoFe-oxide films, and a decrease of the oxide layer with the pan angle and the oxidation pressure is observed. For the same oxidation pressure, the oxidation efficiency depends on the O2 content in the Ar-O2 plasma. These results were applied in optimizing the fabrication of Al2O3 barrier for tunnel junctions. This method was also used to fabricate junctions with Fe-oxide layers inserted at the Al2O3-CoFe interface. TEM and magnetization data indicate that after anneal at 385°C, a homogeneous ferromagnetic Fe-oxide layer (Fe3O4?) is formed.

Bicelles: new nano systems for skin applications

Bicellar systems are lipid nanostructures formed by long- and short-chained phospholipids dispersed in aqueoussolution. Because of their attractive combination of lipid composition, small size and morphological versatility, bicellesbecame new targets for skin research. Bicelles modify the skin biophysical parameters and modulate the skin barrier function acting as enhancers for drug penetration. Moreover, these aggregates have the ability to penetrate through the narrowintercellular spaces of the skin stratum corneum and to reinforce its lipid lamellae. Their structures allows for the incorporation of different molecules that can be carried through the skin layers. Theremarkable versatility of bicelles is their most important characteristic, which makes it possible their use in different fields.These aggregates represent new nanosystems for skin applications. In this work we provide an overview of the main properties ofbicelles and their effects on the skin.

Integrin-Specific Mechanoresponses to Compression and Extension Probed by Cylindrical Flat-Ended AFM Tips in Lung Cells

Cells from lung and other tissues are subjected to forces of opposing directions that are largely transmitted through integrin-mediated adhesions. How cells respond to force bidirectionality remains ill defined. To address this question, we nanofabricated flat-ended cylindrical Atomic Force Microscopy (AFM) tips with ~1 µm2 cross-section area. Tips were uncoated or coated with either integrin-specific (RGD) or non-specific (RGE/BSA) molecules, brought into contact with lung epithelial cells or fibroblasts for 30 s to form focal adhesion precursors, and used to probe cell resistance to deformation in compression and extension. We found that cell resistance to compression was globally higher than to extension regardless of the tip coating. In contrast, both tip-cell adhesion strength and resistance to compression and extension were the highest when probed at integrin-specific adhesions. These integrin-specific mechanoresponses required an intact actin cytoskeleton, and were dependent on tyrosine phosphatases and Ca2+ signaling. Cell asymmetric mechanoresponse to compression and extension remained after 5 minutes of tip-cell adhesion, revealing that asymmetric resistance to force directionality is an intrinsic property of lung cells, as in most soft tissues. Our findings provide new insights on how lung cells probe the mechanochemical properties of the microenvironment, an important process for migration, repair and tissue homeostasis.

Hot wire configuration for depositing device grade nano-crystalline silicon at high deposition rate

The University of Barcelona is developing a pilot-scale hot wire chemical vapor deposition (HW-CVD) set up for the deposition of nano-crystalline silicon (nc-Si:H) on 10 cm × 10 cm glass substrate at high deposition rate. The system manages 12 thin wires of 0.15-0.2 mm diameter in a very dense configuration. This permits depositing very uniform films, with inhomogeneities lower than 2.5%, at high deposition rate (1.5-3 nm/s), and maintaining the substrate temperature relatively low (250 °C). The wire configuration design, based on radicals' diffusion simulation, is exposed and the predicted homogeneity is validated with optical transmission scanning measurements of the deposited samples. Different deposition series were carried out by varying the substrate temperature, the silane to hydrogen dilution and the deposition pressure. By means of Fourier transform infrared spectroscopy (FTIR), the evolution in time of the nc-Si:H vibrational modes was monitored. Particular importance has been given to the study of the material stability against post-deposition oxidation.

Disseny i implementació d'una etapa d'acondicionament per a mesures de conductivitat realitzades amb un microscopi de forces atòmiques

En aquest treball, s’ha dissenyat un mòdul d’acondicionament a fi de millorar les mesures de conductivitat realitzades amb un AFM (Microscopi de Forces Atòmiques). L’equip actual disposa d’un preamplificador de baix soroll amb un guany de 10 10V/A. Donat que els corrents que es pretenen mesurar són extremadament petits (~pA), s’ha dissenyat un filtre per eliminar diferents fonts de soroll, com ara el soroll que introdueix la xarxa elèctrica a 50Hz. Es pretén reduir aquesta component freqüencial un factor mínim de 10 (20dB). També s’ha afegit un filtre passa baixos per eliminar els soroll que es troba fora de l’amplada de banda del preamplificador. S’ha introduït una etapa d’amplificació de guany variable: 1, 10 i 100 per augmentar la flexibilitat de l’equip i finalment també s’ha dissenyat una etapa per eliminar la tensió d’offset d’aquest amplificador. L’abast del treball anirà des del disseny fins la implementació final sobre una placa PCB.

Dipòsit i caracterització de capes primes orgàniques de P3HT:PCBM per a aplicacions fotovoltaiques

En un món on el ritme de la societat actual ens ha portat a considerar les energies enovables com a prioritat vital i necessària i en el que es preveu que la demanda energètica augmenti un 50% fins al 2030, l'interès en la recerca de materials emiconductors orgànics per aplicacions de captura solar, ha assolit un potencial enorme de cara al futur. Molts són el avantatges que presenten aquest tipus de materials en front als seus homòlegs inorgànics. La facilitat de fabricació, la utilització de materials més econòmics i amb menys impacte ambiental, així com la possibilitat de produir dispositius flexibles, són algunes de les atractives aracterístiques que presenten aquests materials. No obstant, certs inconvenients om les baixes eficiències energètiques dels dispositius, i la inestabilitat ambiental ue es tradueix en un temps de vida molt reduït, fan que encara s'hagi d'invertir sforç per aconseguir que aquests materials puguin ser utilitzats en el camp de la aptura d'energia solar. El material més prometedor fins a data d'avui és el P3HT:PCBM. Es tracta d'un sistema polímer:molècula lleugera, on el P3HT actua com a component donador del sistema i el PCBM actua com a component acceptor. Les propietats optoelectròniques i eficiències energètiques de combinats orgànics P3HT:PCBM epèn en gran mesura de la seva morfologia i microestructura. Paràmetres com la proporció entre els components, el dissolvent utilitzat en la dissolució, així com 'aplicació de determinats tractaments tèrmics afecten de forma crítica a la seva orfologia. Durant el present treball s'han utilitzat diverses tècniques de caracterització per a estudiar determinades propietats que presenten aquest tipus de aterials. Entre les tècniques experimentals utilitzades hi trobem la microscòpia FM, l'espectroscòpia Raman i la conductimetria AFM o current sensing AFM CS-AFM). Els experiments en temps real durant l'escalfament de capes primes 3HT:PCBM, mostren que el P3HT pateix una cristal·lització al voltant dels 140ºC, permetent el reordenament de les molècules i un millor solapament del sorbitals [pi]-[pi]*, que resulta en un increment del transport de forats a través de la fase donadora del material. Paralel·lament, entre els 80-120ºC, el material també presenta determinats canvis tant en el comportament dels enllaços, com en la cristal·linitat del material, provocant una quasi transició de fase que atribuïm a la transició vitrea del material. Per altra banda, experiments amb conductimetria AFM realitzats en sistemes P3HT:HDPE mostren un signicatiu augment en la eva estabilitat ambiental, que es tradueix en un augment del temps de vida, sense una pèrdua considerable en els seus valors de conducció. Tot i la combinació del P3HT amb proporcions de polímers aïllants de fins al 80%, el sistema és capaç de no perdre la capacitat de transport gràcies a la formació de fases i dominis rics en P3HT. El present treball posa de manifest que ens trobem davant d'una tecnologia emergent i que nous estudis i esforços en la recerca d'aquest tipus materials és fonamental per aconseguir nous resultats i posicionar als materials semiconductors orgànics com una alternativa viable en el camp dels dispositus fotovoltaics. Assumint dades procedents de la tecnologia actual utilitzada en aquest tipus de materials, estudis i avaluacions ambientals i econòmiques mostren que petits increments tant en les eficiències com en el temps de vida de dispositius basats en aterials orgànics, posicionarien a aquest material com a alternativa totalment viable en el mercat fotovoltaic d'un futur proper.

Inducció local de magnetisme mitjançant irradiació d'ions a través de màscares

Degut a la gran demanda tecnològica, actualment hi ha un gran interès en desenvolupar medis magnètics amb entitats ferromagnètiques de dimensions nanomètriques. Aquesta demanda promou la investigació i el desenvolupament de nous materials i processos de fabricació que permetin controlar d’una manera més precisa les propietats magnètiques i estructurals. Entre els mètodes de litografia convencionals (per exemple deposició física a través de màscares, deposició química en fase vapor i electrodeposició), recentment s’ha demostrat que la irradiació amb ions a través de màscares pre‐litografiades, sembla ser un bon mètode per a la fabricació d’estructures ferromagnètiques de l’ordre dels nanòmetres. Aquesta tècnica pot ser aplicada per aprofitar la transició paramagnètica‐ferromagnètica que presenten alguns materials al ser desordenats estructuralment (per exemple FeAl, FePt3, Ni3Sn2). En el treball que es presenta a continuació s’utilitza l’aliatge Fe60Al40 per a fabricar estructures ferromagnètiques embegudes en una matriu paramagnètica mitjançant irradiació amb ions d’argó a través d’una membrana de polimetil metacrilat (PMMA) prèviament litografiada amb feixos d’electrons (EBL). La fabricació d’aquest sistema té com a objectiu d’estudiar l’evolució de la morfologia i el gruix de PMMA (a partir de SEM i AFM) i del comportament magnètic de les estructures fabricades (MFM i MOKE), quan és irradiat consecutivament a diferents energies. Per a completar l’estudi s’han utilitzat simulacions per a determinar les condicions d’irradiació (TRIM), com per a una millor comprensió dels resultats (simulacions micromagnètiques). El contingut de la memòria inclou una breu introducció històrica i conceptual sobre el magnetisme. A continuació s’exposen les tècniques necessàries per a la fabricació, preparació i caracterització de la mostra. Finalment es presenta una discussió dels resultats obtinguts i les conclusions.

Conduction mechanisms and charge storage in Si-nanocrystals metal-oxide-semiconductor memory devices studied with conducting atomic force microscopy

In this work, we demonstrate that conductive atomic force microscopy (C-AFM) is a very powerful tool to investigate, at the nanoscale, metal-oxide-semiconductor structures with silicon nanocrystals (Si-nc) embedded in the gate oxide as memory devices. The high lateral resolution of this technique allows us to study extremely small areas ( ~ 300nm2) and, therefore, the electrical properties of a reduced number of Si-nc. C-AFM experiments have demonstrated that Si-nc enhance the gate oxide electrical conduction due to trap-assisted tunneling. On the other hand, Si-nc can act as trapping centers. The amount of charge stored in Si-nc has been estimated through the change induced in the barrier height measured from the I-V characteristics. The results show that only ~ 20% of the Si-nc are charged, demonstrating that the electrical behavior at the nanoscale is consistent with the macroscopic characterization.

Modificacion de las propiedades opticas y mecanicas de polimeros mediante implantacion ionica

En el presente trabajo se estudian los efectos introducidos por la implantación de Nitrógeno atómico y Silicio sobre probetas de policarbonato empleadas para usos ópticos. Distintas dosis de Nitrógeno y Silicio fueron implantadas de cara a poner de manifiesto el efecto de la dosis sobre las propiedades ópticas y mecánicas. Se llevaron a cabo ensayos mecánicos de microdureza, nanodureza, y AFM, así como ensayos ópticos de Reflexión-absorción IR y Transmitancia UV-VIS. Los resultados muestran un endurecimiento superficial para las implantaciones a dosis altas de Nitrógeno, así como cambios considerables en los espectros de transmitancia.

Graphoepitaxy of CeO2 on MgO and its application to the fabrication of 45° grain boundary Josephson junctions of YBa2Cu3O7-x

We communicate a detailed study of the epitaxial growth of CeO2 on MgO. The key feature of the growth is the dependence of the in¿plane orientation of the CeO2 epitaxial layer on the MgO surface morphology. Atomic force microscopic (AFM) measurements, x¿ray analyses, as well as high¿resolution transmission electron microscopy (HRTEM) investigations reveal that on rough substrates a cube¿on¿cube growth of CeO2 on MgO occurs while on smooth substrates the CeO2 unit cell is rotated around the surface normal by 45° with respect to the MgO unit cell when the deposition rate is low (~0.3 Å/s) during the first stages of growth. This growth mechanism can be used for a defined fabrication of 45° grain boundaries in the CeO2 layer by controlling the surface roughness of the MgO substrate. This report demonstrates that these 45° grain boundaries may be used to fabricate YBa2Cu3O7¿x Josephson junctions.

Photonic characteristics of Langmuir-Blodgett self-assembled monolayers of colloidal silica particles

Monodispersed colloidal crystals based on silica sub-micrometric particles were synthesized using the Stöber-Fink-Bohn process. The control of nucleation and coalescence result in improved characteristics such as high sphericity and very low size dispersion. The resulting silica particles show characteristics suitable for self-assembling across large areas of closely-packed 2D crystal monolayers by an accurate Langmuir-Blodgett deposition process on glass, fused silica and silicon substrates. Due to their special optical properties, colloidal films have potential applications in fields including photonics, electronics, electro-optics, medicine (detectors and sensors), membrane filters and surface devices. The deposited monolayers of silica particles were characterized by means of FESEM, AFM and optical transmittance measurements in order to analyze their specific properties and characteristics. We propose a theoretical calculation for the photonic band gaps in 2D systems using an extrapolation of the photonic behavior of the crystal from 3D to 2D. In this work we show that the methodology used and the conditions in self-assembly processes are decisive for producing high-quality two-dimensional colloidal crystals by the Langmuir-Blodgett technique.

Feeding of nauplii, copepodites and adults of Calanipeda aquaedulcis (Calanoida) in Mediterranean salt marshes

Feeding of the different developmental stages of Calanipeda aquaedulcis on natural particles (bacterio-, phyto- and microzooplankton) was measured in a Mediterranean salt marsh (Empordà wetlands, NE Iberian Peninsula). Bottle incubations were performed in the field both in autumn and spring. The results showed differences in the diet of the different developmental stages due to both prey type and size. In general, the size of the ingested prey increased with increasing size of the C. aquaedulcis stage. While C. aquaedulcis adults had high ingestion rates and selection coefficients for large prey (micro- and nanoplankton), nauplii preferentially consumed smaller prey items (picoplankton). Copepodites showed the widest prey size range, including pico-, nano- and microplankton. Nevertheless, the lower size limit for particle capture was similar for all stages, i.e. between 1.7 and 2.1 μm. Omnivory was observed in all stages of C. aquaedulcis. Heterotrophic prey (picoplankton, dinoflagellates and ciliates) were the most ingested items. The ability to partition the available food among the different developmental stages could represent an advantage in times of ood scarcity because it may reduce intraspecific competition. This may explain how C. aquaedulcis is able to predominate in the zooplankton community for several weeks during spring and summer ven in situations of low food availability

The use of micro-XRD for the study of glaze color decorations

The compounds responsible for the colours and decorations in glass and glazed ceramics include: colouring agents (transition metal ions), pigments (micro-and nano-precipitates of compounds that either do not dissolve or recrystallize in the glassy matrix) and opacifiers (microcrystalline compounds with high light scattering capability). Their composition, structure and range of stability are highly dependent not only on the composition but also on the procedures followed to obtain them. Chemical composition of the colorants and crystallites may be obtained by means of SEM-EDX and WDX. Synchrotron Radiation micro-X-ray Diffraction has a small beam size adequate (10 to 50 microns footprint size) to obtain the structural information of crystalline compounds and high brilliance, optimal for determining the crystallites even when present in low amounts. In addition, in glass decorations the crystallites often appear forming thin layers (from 10 to 100 micrometers thick) and they show a depth dependent composition and crystal structure. Their nature and distribution across the glass/glazes decorations gives direct information on the technology of production and stability and may be related to the color and appearance. A selection of glass and glaze coloring agents and decorations are studied by means of SR-micro- XRD and SEM-EDX including: manganese brown, antimony yellow, red copper lusters and cobalt blue. The selection includes Medieval (Islamic, and Hispano Moresque) and renaissance tin glazed ceramics from the 10th to the 17th century AD.