Estudio de las capas de acoplamiento y alternativas al reflector de Bragg en estructuras BAW-CRF

Las capas de acoplamiento son un elemento clave en los dispositivos BAW CRF. El factor de acoplamiento K de estas capas permite el diseño de una determinada respuesta. Debido al limitado número de materiales con las que implementarlas, las soluciones que utilizan capas de λ/4 ofrecen un rango discreto de K. Por otra parte, el reflector de Bragg es un mecanismo de aislamiento mecánico entre el sustrato y la estructura BAW que está formado por capas alternas de alta y baja impedancia acústica de λ/4. El problema que presenta es la reducción del factor de calidad asociado a las pérdidas producida por las ondas shear. Este proyecto presenta un método para la obtención de un rango continuo de factores de acoplamiento y estudia la mejora del factor de calidad de las estructuras BAW con reflector de Bragg partiendo de dos materiales con alta y baja impedancia acústica.

Characterisation of the LMS200 laser beam under the influence of blockage surfaces. Influence on 3D scanning of tree orchards

The geometric characterisation of tree orchards is a high-precision activity comprising the accurate measurement and knowledge of the geometry and structure of the trees. Different types of sensors can be used to perform this characterisation. In this work a terrestrial LIDAR sensor (SICK LMS200) whose emission source was a 905-nm pulsed laser diode was used. Given the known dimensions of the laser beam cross-section (with diameters ranging from 12 mm at the point of emission to 47.2 mm at a distance of 8 m), and the known dimensions of the elements that make up the crops under study (flowers, leaves, fruits, branches, trunks), it was anticipated that, for much of the time, the laser beam would only partially hit a foreground target/object, with the consequent problem of mixed pixels or edge effects. Understanding what happens in such situations was the principal objective of this work. With this in mind, a series of tests were set up to determine the geometry of the emitted beam and to determine the response of the sensor to different beam blockage scenarios. The main conclusions that were drawn from the results obtained were: (i) in a partial beam blockage scenario, the distance value given by the sensor depends more on the blocked radiant power than on the blocked surface area; (ii) there is an area that influences the measurements obtained that is dependent on the percentage of blockage and which ranges from 1.5 to 2.5 m with respect to the foreground target/object. If the laser beam impacts on a second target/object located within this range, this will affect the measurement given by the sensor. To interpret the information obtained from the point clouds provided by the LIDAR sensors, such as the volume occupied and the enclosing area, it is necessary to know the resolution and the process for obtaining this mesh of points and also to be aware of the problem associated with mixed pixels.

Sistemes lidar (radar laser) d'ona contínua i baixa potència per a la detecció i mesura de concentració de gasos amb resolució espacial

The present project has performed the study and development of a new technique for the detection of gases with range resolution. This technique called FMCW-lidar is a technique that evolves from the FMCW-radar technique to be applied to lidar systems. Moreover, it takes advantage of the appearance of spectral absorption lines because of the interaction between light and gases to tune the light wavelength of a laser emitter with one of this spectral lines and then detects the backscattered light and analyzes it in order to obtain gas concentration measurements. The first part of the project consisted in the analysis of the WMS technique which is a technique for the in-situ measurement of gases. A complete theoretical analysis has been performed and some experiments have been carried out in order to test the technique and to validate its application to an FMCW-modulated system for the detection of gases. The second part of the project consisted in the analysis of the lidar FMCW technique for solid target detection and its extension to continuous media. The classical form of this technique has been analyzed for a distributed medium and a filtering effect has been found which prevents the accurate acquisition of the medium response. A modification of the technique has been proposed and a validation via simulations and some experiments has been carried on. After performing these tests, a novel system is proposed to be developed and tested in order to perform the indicated gas detection with range resolution.

Growth, optical characterization, and laser operation of a stoichiometric crystal KYb(WO4)(2)

We present our recent achievements in the growing and optical characterization of KYb(WO4)2 (hereafter KYbW) crystals and demonstrate laser operation in this stoichiometric material. Single crystals of KYbW with optimal crystalline quality have been grown by the top-seeded-solution growth slow-cooling method. The optical anisotropy of this monoclinic crystal has been characterized, locating the tensor of the optical indicatrix and measuring the dispersion of the principal values of the refractive indices as well as the thermo-optic coefficients. Sellmeier equations have been constructed valid in the visible and near-IR spectral range. Raman scattering has been used to determine the phonon energies of KYbW and a simple physical model is applied for classification of the lattice vibration modes. Spectroscopic studies (absorption and emission measurements at room and low temperature) have been carried out in the spectral region near 1 µm characteristic for the ytterbium transition. Energy positions of the Stark sublevels of the ground and the excited state manifolds have been determined and the vibronic substructure has been identified. The intrinsic lifetime of the upper laser level has been measured taking care to suppress the effect of reabsorption and the intrinsic quantum efficiency has been estimated. Lasing has been demonstrated near 1074 nm with 41% slope efficiency at room temperature using a 0.5 mm thin plate of KYbW. This laser material holds great promise for diode pumped high-power lasers, thin disk and waveguide designs as well as for ultrashort (ps/fs) pulse laser systems.

Selective ablation of photovoltaic materials with UV laser sources for monolithic interconnection of devices based on a-Si:H

Lasers are essential tools for cell isolation and monolithic interconnection in thin-film-silicon photovoltaic technologies. Laser ablation of transparent conductive oxides (TCOs), amorphous silicon structures and back contact removal are standard processes in industry for monolithic device interconnection. However, material ablation with minimum debris and small heat affected zone is one of the main difficulty is to achieve, to reduce costs and to improve device efficiency. In this paper we present recent results in laser ablation of photovoltaic materials using excimer and UV wavelengths of diode-pumped solid-state (DPSS) laser sources. We discuss results concerning UV ablation of different TCO and thin-film silicon (a-Si:H and nc-Si:H), focussing our study on ablation threshold measurements and process-quality assessment using advanced optical microscopy techniques. In that way we show the advantages of using UV wavelengths for minimizing the characteristic material thermal affection of laser irradiation in the ns regime at higher wavelengths. Additionally we include preliminary results of selective ablation of film on film structures irradiating from the film side (direct writing configuration) including the problem of selective ablation of ZnO films on a-Si:H layers. In that way we demonstrate the potential use of UV wavelengths of fully commercial laser sources as an alternative to standard backscribing process in device fabrication.

Histologic evaluation of thermal damage produced on soft tissues by CO2, Er,Cr:YSGG and diode lasers

Objective: The aim of this in vitro experimental study was to perform histological evaluation of the thermal effect produced on soft tissue irradiated with CO2, Er,Cr:YSGG or diode lasers. Study design: Porcine oral mucosa samples were irradiated with Er,Cr:YSGG laser at 1 W with and without water / air spray, at 2 W with and without water / air spray, and at 4 W with water / air spray, with CO2 laser at 1 W, 2 W, 10 W, 20 W continuous mode and 20 W pulsed mode and diode laser at 2W, 5W, and 10W pulsed mode. The thermal effect was evaluated measuring the width of damaged tissue adjacent to the incision, stained positively for hyalinized tissue with Hematoxylin-Eosin and Masson Trichrome stains. Besides, histological changes in the irradiated tissue were described using subjective grading scales. Results: The evaluated lasers developed a wide range of thermal damage with significant differences between groups. The samples with lowest thermal effect were those irradiated with Er,Cr:YSGG laser using water / air spray, followed by CO2 and diode lasers. Conclusions: Emission parameters of each laser system may influence the thermal damage inflicted on the soft tissue, however, the wave length of each laser determines the absorption rate characteristics of every tissue and the thermal effect

Empleo de óptica adaptativa y fluorescencia en un oftalmoscopio laser de barrido para el registro de células

Estudio elaborado a partir de una estancia en la Universidad de Rochester, Estados Unidos, de octubre del 2006 a enero del 2007. La estancia realizada en la Universidad de Rochester estuvo orientada al aprendizaje en profundidad del oftalmoscopio láser de barrido. El oftalmoscopio láser de barrido emplea una técnica confocal con la finalidad de visualizar diferentes estructuras retinianas en seres vivos. El instrumento diseñado y desarrollado en el Centro de Ciencias de la Visión incorpora un sistema de óptica adaptativa y fluorescencia. La óptica adaptativa aplicada en este oftalmoscopio tiene como objetivo corregir las aberraciones existentes en el ojo y así permitir observar detalles de la retina que de otra forma se verían emborronados. De esta forma se consigue alcanzar valores de resolución muy cercanos a los impuestos por difracción. Por otro lado el uso de fluorescencia tiene por objetivo el permitir la visualización de células y estructuras que, de no ser teñidas, son transparentes a la luz y visible. Esta técnica se ha estado utilizando principalmente en primates y ratas, aunque actualmente también se están llevando a cabo medidas de células de epitelio pigmentario en seres humanos ya que el pigmento contenido en estas células permite la aplicación de la fluorescencia sin necesidad de utilizar tinción.

Increasing the scalability and the speedup of a fish school distributed simulator

El present treball fa un anàlisi i desenvolupament sobre les millores en la velocitat i en l’escalabilitat d'un simulador distribuït de grups de peixos. Aquests resultats s’han obtingut fent servir una nova estratègia de comunicació per als processos lògics (LPs) i canvis en l'algoritme de selecció de veïns que s'aplica a cadascun dels peixos en cada pas de simulació. L’idea proposada permet que cada procés lògic anticipi futures necessitats de dades pels seus veïns reduint el temps de comunicació al limitar la quantitat de missatges intercanviats entre els LPs. El nou algoritme de selecció dels veïns es va desenvolupar amb l'objectiu d'evitar treball innecessari permetent la disminució de les instruccions executades en cada pas de simulació i per cadascun del peixos simulats reduint de forma significativa el temps de simulació.

Terrestrial laser scanning for landslides deformation monitoring

Within last few years a new type of instruments called Terrestrial Laser Scanners (TLS) entered to the commercial market. These devices brought a possibility to obtain completely new type of spatial, three dimensional data describing the object of interest. TLS instruments are generating a type of data that needs a special treatment. Appearance of this technique made possible to monitor deformations of very large objects, like investigated here landslides, with new quality level. This change is visible especially with relation to the size and number of the details that can be observed with this new method. Taking into account this context presented here work is oriented on recognition and characterization of raw data received from the TLS instruments as well as processing phases, tools and techniques to do them. Main objective are definition and recognition of the problems related with usage of the TLS data, characterization of the quality single point generated by TLS, description and investigation of the TLS processing approach for landslides deformation measurements allowing to obtain 3D deformation characteristic and finally validation of the obtained results. The above objectives are based on the bibliography studies and research work followed by several experiments that will prove the conclusions.

Cooperative strategies for imperfect CSI scenarios based on distributed Alamouti

Les comunicacions cooperatives estan guanyant un gran interès en les comunicacions modernes degut a que permeten millorar la transmissió dʼinformació entre un emissor i un receptor utilitzant una sèrie de terminals situats entre ells. Aquest projecte és un estudi complet del sistemes cooperatius, analitzant el seu rendiment i comparant lʼús dʼun sol dʼaquests terminals amb lʼús del codi Alamouti, que utilitza dos terminals. Primer hi ha una introducció als sistemes cooperatius i a la teoria de la informació. Després hem estudiat un sistema cooperatiu amb la teoria de la informació com a base, en termes de probabilitat de fallada del sistema, i posteriorment lʼhem adaptat a un sistema cooperatiu real utilitzant una modulació QPSK, estudiant la seva probabilitat dʼerror de paquet. Finalment es proposen diversos protocols que permeten millorar el rendiment del sistema cooperatiu estudiat.

A first attempt of geographically-distributed Multi-scale integrated analysis of societal and ecosystem metabolism (MuSIASEM): mapping human time and energy throughput in metropolitan Barcelona

This study presents a first attempt to extend the “Multi-scale integrated analysis of societal and ecosystem metabolism (MuSIASEM)” approach to a spatial dimension using GIS techniques in the Metropolitan area of Barcelona. We use a combination of census and commercial databases along with a detailed land cover map to create a layer of Common Geographic Units that we populate with the local values of human time spent in different activities according to MuSIASEM hierarchical typology. In this way, we mapped the hours of available human time, in regards to the working hours spent in different locations, putting in evidence the gradients in spatial density between the residential location of workers (generating the work supply) and the places where the working hours are actually taking place. We found a strong three-modal pattern of clumps of areas with different combinations of values of time spent on household activities and on paid work. We also measured and mapped spatial segregation between these two activities and put forward the conjecture that this segregation increases with higher energy throughput, as the size of the functional units must be able to cope with the flow of exosomatic energy. Finally, we discuss the effectiveness of the approach by comparing our geographic representation of exosomatic throughput to the one issued from conventional methods.

Semigroup analysis of structured populations with distributed states-at-birth arising in mathematical aquaculture

Motivated by the modelling of structured parasite populations in aquaculture we consider a class of physiologically structured population models, where individuals may be recruited into the population at different sizes in general. That is, we consider a size-structured population model with distributed states-at-birth. The mathematical model which describes the evolution of such a population is a first order nonlinear partial integro-differential equation of hyperbolic type. First, we use positive perturbation arguments and utilise results from the spectral theory of semigroups to establish conditions for the existence of a positive equilibrium solution of our model. Then we formulate conditions that guarantee that the linearised system is governed by a positive quasicontraction semigroup on the biologically relevant state space. We also show that the governing linear semigroup is eventually compact, hence growth properties of the semigroup are determined by the spectrum of its generator. In case of a separable fertility function we deduce a characteristic equation and investigate the stability of equilibrium solutions in the general case using positive perturbation arguments.

Technological innovation in creative clusters. The case of laser in conservation of artworks in Florence

The field of laser application to the restoration and cleaning of cultural assets is amongst the most thriving developments of recent times. Ablative laser technological systems are able to clean and protect inestimable works of art subject to atmospheric agents and degradation over time. This new technology, which has been developing for the last forty year, is now available to restorers and has received a significant success all over Europe. An important contribution in the process of laser innovation has been carried out in Florence by local actors belonging to a creative cluster. The objects of the analysis are the genesis of this innovation in this local Florentine context, and the relationships among the main actors who have contributed in it. The study investigates how culture can play a part in the generation of ideas and innovations, and which are the creative environments that can favour it. In this context, the issue of laser technologies for the restoration of cultural heritage has been analysed as a case study in the various paths taken by the Creative Capacity of the Culture (CCC).