Environmental Tax on Products and Services Based on Their Carbon Footprint: A Case Study of the Pulp and Paper Sector

The main aim of this work is to define an environmental tax on products and services based on their carbon footprint. We examine the relevance of conventional life cycle analysis (LCA) and environmentally extended input-output analysis (EIO) as methodological tools to identify emission intensities of products and services on which the tax is based. The short-term price effects of the tax and the policy implications of considering non-GHG are also analyzed. The results from the specific case study on pulp production show that the environmental tax rate based on the LCA approach (1,8%) is higher than both EIO approaches (0,8% for product and 1,4% for industry approach), but they are comparable. Even though LCA is more product specific and provides detailed analysis, EIO would be the more relevant approach to apply economy wide environmental tax. When the environmental tax considers non-GHG emissions instead of only CO2, sectors such as agriculture, mining of coal and extraction of peat, and food exhibit higher environmental tax and price effects. Therefore, it is worthwhile for policy makers to pay attention on the implication of considering only CO2 tax or GHG emissions tax in order for such a policy measure to be effective and meaningful. Keywords: Environmental tax; Life cycle analysis; Environmental input-output analysis.

Stone-ground wood pulp-reinforced polypropylene composites: water uptake and thermal properties

Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC

Low environmental impact bleaching sequences for attaining high brightness level with eucalyptus SPP pulp

The alternatives used for minimizing the usage of chlorine dioxide in bleaching sequences included a hot acid hydrolysis (Ahot) stage, the use of hot chlorine dioxide (Dhot) and ozone stages at medium consistency and high consistency (Zmc and Zhc), in addition to stages with atmospheric hydrogen peroxide (P) and pressurized hydrogen peroxide (PO). The results were interpreted based on the cost of the chemical products, bleaching process yields and on minimizing the environmental impact of the bleaching process. In spite of some process restrictions, high ISO brightness levels were kept around 90 % brightness. Additionally, the inclusion of stages like acid hydrolysis, pressurized peroxide and ozone in the bleaching sequences provided an increase in operating flexibility, aimed at reducing environmental impact (ECF Light). The Dhot(EOP)D(PO) sequence presented lower operating cost for ISO brightness above 92 %. However, this kind of sequence was not allowed for closing the wastewater circuit, even partially. For ISO brightness level around 91%, the AhotZhcDP sequence presented a lower operating cost than the others

Disseny i muntatge d'un sistema de depuració ciclònica per reciclatge de paper

El projecte s’emmarca dins de l’àmbit de la indústria paperera, i dins el procés defabricació del paper es centra concretament amb l’etapa de la depuració ciclònica, una etapa en la qual es pretenen eliminar aquelles partícules sòlides que acompanyen la pasta de paper i que no són desitjables ja que afecten les característiques del paper i el funcionament de la resta d’equips del procés de fabricació. Es presenta una demanda de projecte per part del grup LEPAMAP (Laboratori d’Enginyeria Paperera i Materials Polímers) sobre el disseny d’una instal•lació de depuració ciclònica, mitjançant un hidrocicló, per realitzar activitats de recerca. Un hidrocicló és un equip que separa gràcies a la força centrífuga del flux d’entrada i pel seu disseny amb forma de con invertit. Així doncs, els objectius bàsics d’aquest projecte són dissenyar una instal•lació de depuració adequada per depurar una pasta de paper de possibles contaminants sòlids, la qual cosa implica el disseny d’una bomba centrífuga per impulsar el flux cap a l’interior de l’hidrocicló, dipòsits per emmagatzemar i preparar la suspensió, un agitador per mantenir en tot moment la homogeneïtat de la suspensió i uns dispositius de mesura i control per mesurar i controlar variables com el cabal, la pressió o el volum.El segon objectiu tracta de posar en marxa la instal•lació i comprovar si aquest equip,l’hidrocicló, separa correctament les partícules sòlides del flux de pasta.Paral•lelament s’ha estudiat quins són els equips de depuració més importants a laindústria paperera així com les etapes més importants que formen part del procés de fabricació del paper

Materials nanocomposits a partir de whiskers de cel•lulosa i matriu polimèrica de cautxú

De acuerdo con los objetivos generales del proyecto y plan de trabajo previsto, para esta anualidad, se obtuvieron fibras y microfibras de celulosa a partir de dos fuentes: celulosa vegetal de pino y eucalipto y celulosa bacterial. Las microfibrillas han sido utilizadas como material de refuerzo para la fabricación de materiales compuestos a partir de caucho natural, policaprolactona y polivinil alcohol. Las muestras se fabricaron mediante la técnica de "casting" en medio acuoso y temperatura ambiente. Las muestras fueron caracterizados en sus propiedades mecánicas, físicas y térmicas. Se observó que, en general, la adición de las microfibrillas de celulosa en las matrices poliméricas provoca una mejora sustancial en las propiedades mecánicas del material en comparación con el polímero sin reforzar. Los resultados pueden resumirse de la siguiente manera: 1.Fabricación de materiales compuestos a base de caucho natural y fibras de celulosa. Se obtuvieron fibras y nanofibras de celulosa que fueron modificadas químicamente y usadas como refuerzo en matriz de caucho. Los resultados mostraron mejora de propiedades mecánicas del material, principalmente en los materiales compuestos reforzados con nanofibras. 2. Obtención de whiskers de celulosa y su utilización como material de refuerzo en una matriz de policaprolactona. Se obtuvieron whiskers de celulosa a partir de pasta blanqueada. La adición en una matriz de policaprolactona produjo materiales compuestos con propiedades mecánicas superiores a la matriz, con buena dispersión de los whiskers. 3. Obtención de fibras de celulosa bacterial y nanofibras de celulosa, aislamiento y utilización sobre una matriz de polivinil alcohol. Se obtuvo celulosa bacterial a partir de la bacteria Gluconacetobacter xylinum. Además se fabricaron nanofibras de celulosa a partir eucalipto blanqueado. La celulosa bacterial como material de refuerzo no produjo importantes mejoras en las propiedades mecánicas de la matriz; en cambio se observaron mejoras destacables con la nanofibra como refuerzo.

Acoustic properties of polypropylene composites reinforced with stone groundwood

Currently, acoustic isolation is one of the problems raised with building construction in Spain. The publication of the Basic Document for the protection against noise of the Technical Building Code has increased the demand of comfort for citizens. This has created the need to seek new composite materials that meet the new required acoustical building codes. In this paper we report the results of the newly developed composites that are able to improve the acoustic isolation of airborne noise. These composites were prepared from polypropylene (PP) reinforced with mechanical pulp fibers from softwood (Pinus radiata). Mechanical and acoustical properties of the composites from mechanical pulp (MP) and polypropylene (PP) have been investigated and compared to fiberglass (FG) composites. MP composites had lower tensile properties compared with FG composites, although these properties can be improved by incorporation of a coupling agent. The results of acoustical properties of MP composites were reported and compared with the conventional composites based on fiberglass and gypsum plasterboards. Finally, we suggest the application of MP composites as a light-weight building material to reduce acoustic transmitions

Estudi de reactius químics alternatius per al blanqueig de pastes termomecàniques : efecte en les propietats òptiques de les pastes i en la qualitat dels efluents del procés

Aquest estudi s’emmarca en un projecte titulat “Noves possibilitats en el blanqueig en lespastes destintades: Alternatives al blanqueig amb sosa càustica i peròxid d’hidrogen” i estàsubvencionat per diverses empreses europees del sector. La seva realització s’ha dut a termeen el Centre Technique du Papier, a Grenoble, França. L’estudi contempla la realitzaciód’una part del projecte, i té per objecte analitzar els Na2SiO3 modificats, el hidròxid demagnesi (Mg(OH)2) i el hidròxid de calci (Ca(OH)2) per veure si poden actuar com asubstituts del NaOH. Cal intentar aconseguir valors de blancor similars als assolits amb elblanqueig estàndard i millorar substancialment la qualitat de les aigües. Segons el centre derecerca es pot considerar una millora projectable a nivell industrial una reducció de la DQO ide la demanda catiònica a partir d’un 10% a nivell experimental.La pasta que es blanqueja és TMP verge. Els resultats obtinguts a nivell de blancor tambépoden ser considerats aplicables en paper recuperat, prèviament destintat, provenintd’aquest tipus de pasta

The suitability of steam exploded vitis vinifera and alkaline lignin for the manufacture of fiberboard

The main objective of this study was to explore the suitability of Vitis vinifera as a raw material and alkaline lignin as a natural binder for fiberboard manufacturing. In the first step, Vitis vinifera was steam- exploded through a thermo-mechanical vapor process in a batch reactor, and the obtained pulp was dried, ground, and pressed to produce the boards. The effects of pretreatment factors and pressing conditions on the chemical composition of the fibers and the physico-mechanical properties of binderless fiberboards were evaluated, and the conditions that optimize these properties were found. A response surface method based on a central composite design and multiple-response optimization was used. The variables studied and their respective variation ranges were: pretreatment temperature (Tr: 190-210ºC), pretreatment time (tr: 5-10 min), pressing temperature (Tp: 190-210ºC), pressing pressure (Pp: 8-16MPa), and pressing time (tp: 3-7min). The results of the optimization step show that binderless fiberboards have good water resistance and weaker mechanical properties. In the second step, fiberboards based on alkaline lignin and Vitis vinifera pulp produced at the optimal conditions determined for binderless fiberboards were prepared and their physico-mechanical properties were tested. Our results show that the addition of about 15% alkaline lignin leads to the production of fiberboards that fully meet the requirements of the relevant standard specifications

A Neanderthal Lower Incisor from Cova del Gegant (Sitges, Barcelona, Spain)

Cova del Gegant is located near the city of Sitges (Barcelona, Spain). The cave is a small karst system which contains Upper Pleistocene archaeological and paleontological material (DauRa et al., 2005). The site was first excavated in 1954 and then in 1972 and 1974- (Viñas, 1972; Viñas & Villalta, 1975) and in 1985 and 1989 (maRtínez et al., 1985; moRa, 1988; maRtínez et al., 1990). Finally, in 2007, Grup de Recerca del Quaternari has restarted the archaeological research at Cova del Gegant (DauRa, 2008; DauRa et al., 2010). A human mandible was recovered during the first field season in 1954 and was recently published by DauRa et al. (2005). In the present study, we describe a new human tooth (left I2) that appeared, like the mandible, in a revision of the faunal material recovered from the site in 1974-1975. The specimen preserves the entire crown and the cervical two thirds of the root (Figure 1). The lack of the root apex makes it difficult to determine if the tooth was fully developed at the time of death. However, CT analysis reveals a pulp cavity that could be still open, suggesting root formation was incomplete. The specimen shows only slight dental wear corresponding to stage 2 of Molnar (1971 en Hillson, 1996). Morphologically, the crown shows slight shovelling and a lingual tubercle and appears similar to Neandertal incisors. Standard crown measurements (buccolingual diameter=7.7 mm; mesiodistal diameter= 7.3 mm) (Figure 2) suggest a fairly large tooth, particularly in the BL dimension, again resembling Neandertals in this regard. Discriminant analysis classified the Gegant incisor as Neandertal with a 99.8% posterior probability (Table 2). Association of this tooth with the previously described mandible is considered unlikely given the different ages at death estimated for each. Thus, there appear to be two individuals preserved in the sediments of the Gegant cave, one adult and one subadult (around 8-10 years old).

Histopathological evaluation of root canal filling materials for primary teeth

This study aimed to assess the response of apical and periapical tissues of dogs¿ teeth after root canal filling with different materials. Forty roots from dogs¿ premolars were prepared biomechanically and assigned to 4 groups filled with: Group I: commercial calcium hydroxide and polyethylene glycol-based paste (Calen®) thickened with zinc oxide; Group II: paste composed of iodoform, Rifocort® and camphorated amonochlorophenol; Group III: zinc oxide-eugenol cement; Group IV: sterile saline. After 30 days, the samples were subjected to histological processing. The histopathological findings revealed that in Groups I and IV the apical and periapical regions exhibited normal appearance, with large number of fibers and cells and no resorption of mineralized tissues. In Group II, mild inflammatory infiltrate and mild edema were observed, with discrete fibrogenesis and bone resorption. Group III showed altered periapical region and thickened periodontal ligament with presence of inflammatory cells and edema. It may be concluded that the Calen paste thickened with zinc oxide yielded the best tissue response, being the most indicated material for root canal filling of primary teeth with pulp vitality.

Study and modeling of the desintegration kinetics of coated paper

The disintegration of recovered paper is the first operation in the preparation of recycled pulp. It is known that the defibering process follows a first order kinetics from which it is possible to obtain the disintegration kinetic constant (KD) by means of different ways. The disintegration constant can be obtained from the Somerville index results (%lsv and from the dissipated energy per volume unit (Ss). The %slv is related to the quantity of non-defibrated paper, as a measure of the non-disintegrated fiber residual (percentage of flakes), which is expressed in disintegration time units. In this work, disintegration kinetics from recycled coated paper has been evaluated, working at 20 revise rotor speed and for different fiber consistency (6, 8, 10, 12 and 14%). The results showed that the values of experimental disintegration kinetic constant, Ko, through the analysis of Somerville index, as function of time. Increased, the disintegration time was drastically reduced. The calculation of the disintegration kinetic constant (modelled Ko), extracted from the Rayleigh’s dissipation function, showed a good correlation with the experimental values using the evolution of the Somerville index or with the dissipated energy

Study and modeling of the desintegration kinetics of coated paper

The disintegration of recovered paper is the first operation in the preparation of recycled pulp. It is known that the defibering process follows a first order kinetics from which it is possible to obtain the disintegration kinetic constant (KD) by means of different ways. The disintegration constant can be obtained from the Somerville index results (%lsv and from the dissipated energy per volume unit (Ss). The %slv is related to the quantity of non-defibrated paper, as a measure of the non-disintegrated fiber residual (percentage of flakes), which is expressed in disintegration time units. In this work, disintegration kinetics from recycled coated paper has been evaluated, working at 20 revise rotor speed and for different fiber consistency (6, 8, 10, 12 and 14%). The results showed that the values of experimental disintegration kinetic constant, Ko, through the analysis of Somerville index, as function of time. Increased, the disintegration time was drastically reduced. The calculation of the disintegration kinetic constant (modelled Ko), extracted from the Rayleigh’s dissipation function, showed a good correlation with the experimental values using the evolution of the Somerville index or with the dissipated energy

In vitro evaluation of the temperature increment at the external root surface after Er,Cr: YSGG laser irradiation of the root canal

Objectives: A study was made to determine the temperature increment at the dental root surface following Er,Cr:YSGG laser irradiation of the root canal. Design. Human canines and incisors previously instrumented to K file number ISO 30 were used. Irradiation was carried out with glass fiber endodontic tips measuring 200 μm in diameter and especially designed for insertion in the root canal. The teeth were irradiated at 1 and 2 W for 30 seconds, without water spraying or air, and applying a continuous circular movement (approximately 2 mm/sec.) in the apico-coronal direction. Results: At the 1 W power setting, the mean temperature increment was 3.84ºC versus 5.01ºC at 2 W. In all cases the difference in mean value obtained after irradiation versus the mean baseline temperature proved statistically significant (p< 0.05). Conclusions: Application of the Er,Cr:YSGG laser gives rise to a statistically significant temperature increment at the external root surface, though this increment is probably clinically irrelevant, since it would appear to damage the tissues (periodontal ligament and alveolar bone) in proximity to the treated tooth

Study and modeling of the desintegration kinetics of coated paper

The disintegration of recovered paper is the first operation in the preparation of recycled pulp. It is known that the defibering process follows a first order kinetics from which it is possible to obtain the disintegration kinetic constant (KD) by means of different ways. The disintegration constant can be obtained from the Somerville index results (%lsv and from the dissipated energy per volume unit (Ss). The %slv is related to the quantity of non-defibrated paper, as a measure of the non-disintegrated fiber residual (percentage of flakes), which is expressed in disintegration time units. In this work, disintegration kinetics from recycled coated paper has been evaluated, working at 20 revise rotor speed and for different fiber consistency (6, 8, 10, 12 and 14%). The results showed that the values of experimental disintegration kinetic constant, Ko, through the analysis of Somerville index, as function of time. Increased, the disintegration time was drastically reduced. The calculation of the disintegration kinetic constant (modelled Ko), extracted from the Rayleigh’s dissipation function, showed a good correlation with the experimental values using the evolution of the Somerville index or with the dissipated energy

Erupted odontomas: a report of three cases and review of the literature

Introduction: Odontomas are benign odontogenic tumors composed of enamel, dentine, cement and pulp tissue. They are usually clinically asymptomatic, but often associated with tooth eruption disturbances. In exceptional cases the odontoma erupts into the mouth. The present study reports three cases of odontomas erupted into the oral cavity and reviews the literature. Clinical cases: The first case was an 11-year-old girl with impacted 4.6 associated to a radiopaque mass measuring about 2 cm in diameter. The histological diagnosis was complex odontoma. A clinical and radiological follow-up of 4.6 was carried out until its spontaneous eruption. The second case was a 26-year-old male presenting a hard, yellowish-brown mass located distal to the upper left second molar. Computed tomography confi rmed the presence of a radiopaque lesion, and the histopathological study confirmed a complex odontoma. The third patient was a 27-year-old male reporting tongue irritation due to tooth eruption in the inferior lingual region. A periapical radiograph revealed a mixed radiopaque lesion associated to impacted 3.2. The histological report in this case indicated a compound odontoma. Discussion: Odontomas erupting into the oral cavity are rare. The first case was published in 1980, and since then only 17 cases have been reported in the literature. Eight of the 17 cases were complex odontomas; the rest were compound odontomas. Pain, swelling and infection were the most common symptoms, and 13 cases presented an impacted tooth associated with the lesion