La crisi sub-prime i el crack de 1929: Comparació d'episodis d'eufòria financera

Treball de recerca realitzat per un alumne d'ensenyament secundari i guardonat amb un Premi CIRIT per fomentar l'esperit científic del Jovent l'any 2009. La present investigació té per objecte d’estudi la relació, atès el període de turbulències econòmiques que travessa el món globalitzat, entre els episodis d’eufòria financera i les crisi financeres i econòmiques, i la periodicitat amb les que aquestes es produeixen. Aquesta pretén confrontar-se des d’una aproximació històric-econòmica, mitjançant l’anàlisi i la comparació de dos successos -el crack borsari de 1929 i la crisi sub-prime- per tal de demostrar la existència de comuns denominadors, i, a la llum dels resultats, apreciar les conclusions que aporta la Història. Serà, doncs, aquesta periodicitat i les seves implicacions la qual s'ambicionarà contrastar amb la realitat mitjançant l'aplicació i l'anàlisi pràctica de dos episodis rellevants i paradigmàtics, amb el recolzament i l'autoritat del model comparatiu establerts per l'economista John Kenneth Galbraith al seu llibre ''Breve historia de la euforia financiera''.

Parametric analysis of different compact tension specimens for fracture toughness characterisation in woven composite materials

Estudi elaborat a partir d’una estada a l’ Imperial College London, entre juliol i novembre de 2006. En aquest treball s’ha investigat la geometria més apropiada per a la caracterització de la tenacitat a fractura intralaminar de materials compòsits laminats amb teixit. L’objectiu és assegurar la propagació de l’esquerda sense que la proveta falli abans per cap altre mecanisme de dany per tal de permetre la caracterització experimental de la tenacitat a fractura intralaminar de materials compòsits laminats amb teixit. Amb aquesta fi, s’ha dut a terme l’anàlisi paramètrica de diferents tipus de provetes mitjançant el mètode dels elements finits (FE) combinat amb la virtual crack closure technique (VCCT). Les geometries de les provetes analitzades corresponen a la proveta de l’assaig compact tension (CT) i diferents variacions com la extended compact tension (ECT), la proveta widened compact tension (WCT), tapered compact tension (TCT) i doubly-tapered compact tension (2TCT). Com a resultat d’aquestes anàlisis s’han derivat diferents conclusions per obtenir la geometria de proveta més apropiada per a la caracterització de la tenacitat a fractura intralaminar de materials compòsits laminats amb teixit. A més, també s’han dut a terme una sèrie d’assaigs experimentals per tal de validar els resultats de les anàlisis paramètriques. La concordança trobada entre els resultats numèrics i experimentals és bona tot i la presència d’efectes no previstos durant els assaigs experimentals.

Development of an optimized methodology for tensile testing of carbon steels in hydrogen environment

The study was performed at OCAS, the Steel Research Centre of ArcelorMittal for the Industry market. The major aim of this research was to obtain an optimized tensile testing methodology with in-situ H-charging to reveal the hydrogen embrittlement in various high strength steels. The second aim of this study has been the mechanical characterization of the hydrogen effect on hight strength carbon steels with varying microstructure, i.e. ferrite-martensite and ferrite-bainite grades. The optimal parameters for H-charging - which influence the tensile test results (sample geometry type of electrolyte, charging methods effect of steel type, etc.) - were defined and applied to Slow Strain Rate testing, Incremental Step Loading and Constant Load Testing. To better understand the initiation and propagation of cracks during tensile testing with in-situ H-charging, and to make the correlation with crystallographic orientation, some materials have been analyzed in the SEM in combination with the EBSD technique. The introduction of a notch on the tensile samples permits to reach a significantly improved reproducibility of the results. Comparing the various steel grades reveals that Dual Phase (ferrite-martensite) steels are more sensitive to hydrogen induced cracking than the FB (ferritic-bainitic) ones. This higher sensitivity to hydrogen was found back in the reduced failure times, increased creep rates and enhanced crack initiation (SEM) for the Dual Phase steels in comparison with the FB steels.

Efecto de la microestructura en el comportamiento mecánico de aceros de herramienta para trabajo en frío

El estudio desarrollado en la tesis doctoral profundiza en las relaciones existentes entre la microestructura y el comportamiento a rotura y fatiga de tres tipos de Aceros de Herramienta para trabajo en Frío, dos obtenidos por colada y un tercero mediante pulvimetalúrgia. En primer lugar se evaluaron los aspectos microestructurales relacionados con las dos vias de procesamiento empleadas, además del efecto del cambio en la composición química. Asimismo se documentó la influencia del trabajado en caliente sobre la isotropía microestructural. Considerando las caracteristicas microestructurales se evaluó el comportamiento a rotura en tres orientaciones referidas al sentido de la deformación en caliente. Para ello , se empleó la Mecánica de la Fractura Elástica Lineal como marco analítico. Los resultados fueron tratados siguiendo la estadística de Weibull. Para el caso de los aceros colados se implementa un analisis de curva-R para explicar el crecimiento subcrítico de grietas observado experimentalmente. El estudio del comportamiento a fatiga incluyó la determinación del limite a fatiga para todas la orientaciones microestructurales escogidas y el estudio de la cinetica de propagación de fisuras físicamente pequeñas para la orientación con mejor respuesta mecánica.

Failure mechanism under tensile loads in CFRP 0-90º cross-ply laminates containing voids

The failure mechanism of a voided CFRP 0-90° cross-ply laminate under tensile loads applied in one direction was studied in this Final Degree Project. For this purpose, voided coupons were manufactured for being tested and a FEA was done. In both investigations, voids were placed in 90º and 0º direction, in order to understand the void location influence. On the one hand, the behaviour of the voided laminates was investigated through a FEM in order to preview the stress distribution within the material. On the other hand, voided specimens where manufactured by applying blowing agent in between the inner layers. These specimens were tested by a quasi-static step wise tensile test where data showing its real behaviour was collected. Specimens were X-rayed after each step of the test in order to investigate the failure mechanism of the composite. Data from the test was studied so that relations such as strength of the laminates, crack density per stress, void length per first crack at the void and void area per first crack at the specimen could be characterized

Structural characterization of laser-treated Cr3C2-NiCr coatings

The interconnected porosity of the Cr3C2-NiCr coatings obtained by high-velocity oxy fuel spraying is detrimental in corrosion and wear resistance applications. Laser treatments allow sealing of their surfaces through melting and resolidification of a thin superficial layer. A Nd:YAG laser beam was used to irradiate Cr3C2-NiCr coatings either in the continuous wave mode or at different repetition rates in the pulsed one. Results indicated that high peak and low mean laser irradiances are not good, since samples presented deep grooves and an extensive crack network. At low peak and higher mean laser irradiances the surface was molten, and only a few shallow cracks were observed. The interconnected porosity was completely eliminated in a layer up to 80 m thick, formed by large Cr7C3 grains imbedded in a NiCr matrix.

Eyes wide shut - unusual two stage repair of pectus excavatum and annuloaortic ectasia in a 37 year old marfan patient: Case report

We report about a 37 year old male patient with a pectus excavatum. The patient was in NYHA functional class III. After performed computed tomography the symptoms were thought to be related to the severity of chest deformation. A Ravitch-procedure had been accomplished in a district hospital in 2009. The crack of a metal bar led to a reevaluation 2010, in which surprisingly the presence of an annuloaortic ectasia (root 73 × 74 mm) in direct neighborhood of the formerly implanted metal-bars was diagnosed. Echocardiography revealed a severe aortic valve regurgitation, the left ventricle was massively dilated presenting a reduced ejection fraction of 45%. A marfan syndrome was suspected and the patient underwent a valve sparing aortic root replacement (David procedure) in our institution with an uneventful postoperative course. A review of the literature in combination with discussion of our case suggests the application of stronger recommendations towards preoperative cardiovascular assessment in patients with pectus excavatum.

Structural characterization of laser-treated Cr3C2-NiCr coatings

The interconnected porosity of the Cr3C2-NiCr coatings obtained by high-velocity oxy fuel spraying is detrimental in corrosion and wear resistance applications. Laser treatments allow sealing of their surfaces through melting and resolidification of a thin superficial layer. A Nd:YAG laser beam was used to irradiate Cr3C2-NiCr coatings either in the continuous wave mode or at different repetition rates in the pulsed one. Results indicated that high peak and low mean laser irradiances are not good, since samples presented deep grooves and an extensive crack network. At low peak and higher mean laser irradiances the surface was molten, and only a few shallow cracks were observed. The interconnected porosity was completely eliminated in a layer up to 80 m thick, formed by large Cr7C3 grains imbedded in a NiCr matrix.

Velocity fluctuations of fracturelike disruptions of associating polymer solutions

Velocity has been measured as a function of time for propagating crack tips as water is injected into solutions of end-capped associating polymers in a rectanguar Hele-Shaw cell. Measurements were performed for flows with different values of cell gap, channel width, polymer molecular weight, and polymer concentration. The condition for the onset of fracturelike behavior is well described by a Deborah number which uses the shear-thinning shear rate of the polymer solution as a characteristic frequency for network relaxation. At low molecular weight, the onset of fracturelike pattern evolution is accompanied by an abrupt jump in tip velocity, followed by a lower and approximately constant acceleration. At high molecular weight, the transition to fracturelike behavior involves passing through a regime that may be understood in terms of stick-slip dynamics. The crack-tip wanders from side to side and fluctuates (in both speed and velocity along the channel) with a characteristic frequency which depends linearly on the invading fluid injection rate.

Mechanical properties of viral capsids

Viruses are known to tolerate wide ranges of pH and salt conditions and to withstand internal pressures as high as 100 atmospheres. In this paper we investigate the mechanical properties of viral capsids, calling explicit attention to the inhomogeneity of the shells that is inherent to their discrete and polyhedral nature. We calculate the distribution of stress in these capsids and analyze their response to isotropic internal pressure (arising, for instance, from genome confinement and/or osmotic activity). We compare our results with appropriate generalizations of classical (i.e., continuum) elasticity theory. We also examine competing mechanisms for viral shell failure, e.g., in-plane crack formation vs radial bursting. The biological consequences of the special stabilities and stress distributions of viral capsids are also discussed.

Brittle to ductile transition in a fiber bundle with strong heterogeneity

We analyze the failure process of a two-component system with widely different fracture strength in the framework of a fiber bundle model with localized load sharing. A fraction 0≤α≤1 of the bundle is strong and it is represented by unbreakable fibers, while fibers of the weak component have randomly distributed failure strength. Computer simulations revealed that there exists a critical composition αc which separates two qualitatively different behaviors: Below the critical point, the failure of the bundle is brittle, characterized by an abrupt damage growth within the breakable part of the system. Above αc, however, the macroscopic response becomes ductile, providing stability during the entire breaking process. The transition occurs at an astonishingly low fraction of strong fibers which can have importance for applications. We show that in the ductile phase, the size distribution of breaking bursts has a power law functional form with an exponent μ=2 followed by an exponential cutoff. In the brittle phase, the power law also prevails but with a higher exponent μ=92. The transition between the two phases shows analogies to continuous phase transitions. Analyzing the microstructure of the damage, it was found that at the beginning of the fracture process cracks nucleate randomly, while later on growth and coalescence of cracks dominate, which give rise to power law distributed crack sizes.

Avances en el estudio del "torrao" o cribado del tomate

El "torrao" es una enfermedad presente en nuestro país desde 2001, que sigue presentándose en cada campaña de tomate con mayor o menor incidencia según el año. Las plantas afectadas muestran necrosis en la parte basal de los foliolos que puede evolucionar a cribado, manchas longitudinales en los peciolos y manchas necróticas en fruto, que terminan por rajarlo. El presente trabajo es la continuación del publicado en el número 32 de esta revista titulado "Necrosis del tomate: "torrao" o cribado" y surge de los resultados obtenidos tras la reciente publicación de la identificación y caracterización del nuevo virus "Tomato torrado virus" (ToTV) como agente implicado en la enfermedad conocida como "torrao". En este estudio se seleccionaron 94 muestras procedentes de prospecciones realizadas en invernaderos de Murcia durante los años 2003 a 2006. La aplicación RT-PCR e hibridación molecular para la detección de ToTV ha permitido detectar la presencia de esta nueva virosis en 87 de las muestras analizadas. En 83 de ellas, se encontró la presencia conjunta de este nuevo virus con el Pepino mosaic virus (PepMV), mayoritariamente con el aislado tipo Chileno 2 (Accesión number: DQ00095). Se plantean nuevos estudios para determinar la implicación de ambos virus, ToTV y PepMV, en el desarrollo del síndrome conocido como "torrao" del tomate.

Necrosis del tomate: "torrao "o "cribado"

Desde la primavera de 2001, viene presentándose en España una nueva enfermedad conocida con el nombre de "torrao" o "cribado". Los síntomas que habitualmente presentan las plantas afectadas son una necrosis en la parte basal del foliolo que evoluciona a cribado, en los peciolos aparecen manchas longitudinales en ocasiones endurecidas que llegan a curvar los foliolos, y los frutos manifiestan manchas necróticas, deformaciones que finalmente lo rajan, quedando comercialmente inviables. Muestreos realizados desde su aparición han determinado la mayor incidencia de la enfermedad en la zona de Murcia, seguido de Canarias y en menor proporción Almería, y Alicante. Los resultados de los análisis realizados a las 369 muestras recogidas determinan que el 67% de las muestras analizadas eran positivas a Pepino mosaic virus (PepMV). En los ensayos de transmisión, únicamente mediante el injerto, se consiguió reproducir los síntomas de la enfermedad en dos casos, en el resto las plantas inoculadas e injertadas únicamente mostraban síntomas típicos de PepMV y los análisis realizados confirmaron este aspecto. A la vista de los resultados obtenidos, se diseñó un nuevo método de diagnóstico que ha permitido la caracterización del 89% de las muestras analizadas como aislado Chileno 2 de PepMV, recientemente publicado en el Gen Bank (Accesión number: DQ000985). De acuerdo con lo expuesto podría tratarse de uno de los agentes implicados en el desarrollo del síndrome junto con otros factores aún por determinar

Smoked cocaine in socially-depressed areas

Background: The main objectives of this study are to describe the smoked cocaine user's profile in socially-depressed areas and their needs from a harm-reduction perspective, to investigate their use of smoking crack and compare the acute effects between injecting and smoking consumption. Methods: The study took place in SAPS, Barcelona, Spain. Two focus group sessions were undertaken with a total of 8 drug users. Secondly, the 8 participants answered a structured questionnaire and in the course of the sessions, as a snowball activity, were trained to survey 6 other crack smokers. Results: We obtained 56 questionnaires. The majority of participants were from non-European Community countries (62.69%), 70.2% of participants referred to sharing the smoking equipment. The most frequent symptoms reported during smoked cocaine were mydriasis (83.33%)), perspiration (72.92%) and compulsive object search (70.83%) During the group sessions, participants said that smoked cocaine is much more addictive than injected cocaine and causes more anxiety. Participants also reported the difficulty of changing from injected use to smoked use, due to the larger amount of cocaine needed to reach the same effects as when having injected. Conclusions We can conclude that the research, focused on achieving greater knowledge of the smoked cocaine user's profile, their usage of smoking crack, consumption patterns and acute effects, should be incorporated into substance misuse interventions.

A Thermodynamically Consistent Damage Model for Advanced Composites

A continuum damage model for the prediction of damage onset and structural collapse of structures manufactured in fiber-reinforced plastic laminates is proposed. The principal damage mechanisms occurring in the longitudinal and transverse directions of a ply are represented by a damage tensor that is fixed in space. Crack closure under load reversal effects are taken into account using damage variables established as a function of the sign of the components of the stress tensor. Damage activation functions based on the LaRC04 failure criteria are used to predict the different damage mechanisms occurring at the ply level. The constitutive damage model is implemented in a finite element code. The objectivity of the numerical model is assured by regularizing the dissipated energy at a material point using Bazant’s Crack Band Model. To verify the accuracy of the approach, analyses ofcoupon specimens were performed, and the numerical predictions were compared with experimental data