Low environmental impact bleaching sequences for attaining high brightness level with eucalyptus SPP pulp

The alternatives used for minimizing the usage of chlorine dioxide in bleaching sequences included a hot acid hydrolysis (Ahot) stage, the use of hot chlorine dioxide (Dhot) and ozone stages at medium consistency and high consistency (Zmc and Zhc), in addition to stages with atmospheric hydrogen peroxide (P) and pressurized hydrogen peroxide (PO). The results were interpreted based on the cost of the chemical products, bleaching process yields and on minimizing the environmental impact of the bleaching process. In spite of some process restrictions, high ISO brightness levels were kept around 90 % brightness. Additionally, the inclusion of stages like acid hydrolysis, pressurized peroxide and ozone in the bleaching sequences provided an increase in operating flexibility, aimed at reducing environmental impact (ECF Light). The Dhot(EOP)D(PO) sequence presented lower operating cost for ISO brightness above 92 %. However, this kind of sequence was not allowed for closing the wastewater circuit, even partially. For ISO brightness level around 91%, the AhotZhcDP sequence presented a lower operating cost than the others

Environmental Tax on Products and Services Based on Their Carbon Footprint: A Case Study of the Pulp and Paper Sector

The main aim of this work is to define an environmental tax on products and services based on their carbon footprint. We examine the relevance of conventional life cycle analysis (LCA) and environmentally extended input-output analysis (EIO) as methodological tools to identify emission intensities of products and services on which the tax is based. The short-term price effects of the tax and the policy implications of considering non-GHG are also analyzed. The results from the specific case study on pulp production show that the environmental tax rate based on the LCA approach (1,8%) is higher than both EIO approaches (0,8% for product and 1,4% for industry approach), but they are comparable. Even though LCA is more product specific and provides detailed analysis, EIO would be the more relevant approach to apply economy wide environmental tax. When the environmental tax considers non-GHG emissions instead of only CO2, sectors such as agriculture, mining of coal and extraction of peat, and food exhibit higher environmental tax and price effects. Therefore, it is worthwhile for policy makers to pay attention on the implication of considering only CO2 tax or GHG emissions tax in order for such a policy measure to be effective and meaningful. Keywords: Environmental tax; Life cycle analysis; Environmental input-output analysis.

Materials nanocomposits a partir de whiskers de cel•lulosa i matriu polimèrica de cautxú

De acuerdo con los objetivos generales del proyecto y plan de trabajo previsto, para esta anualidad, se obtuvieron fibras y microfibras de celulosa a partir de dos fuentes: celulosa vegetal de pino y eucalipto y celulosa bacterial. Las microfibrillas han sido utilizadas como material de refuerzo para la fabricación de materiales compuestos a partir de caucho natural, policaprolactona y polivinil alcohol. Las muestras se fabricaron mediante la técnica de "casting" en medio acuoso y temperatura ambiente. Las muestras fueron caracterizados en sus propiedades mecánicas, físicas y térmicas. Se observó que, en general, la adición de las microfibrillas de celulosa en las matrices poliméricas provoca una mejora sustancial en las propiedades mecánicas del material en comparación con el polímero sin reforzar. Los resultados pueden resumirse de la siguiente manera: 1.Fabricación de materiales compuestos a base de caucho natural y fibras de celulosa. Se obtuvieron fibras y nanofibras de celulosa que fueron modificadas químicamente y usadas como refuerzo en matriz de caucho. Los resultados mostraron mejora de propiedades mecánicas del material, principalmente en los materiales compuestos reforzados con nanofibras. 2. Obtención de whiskers de celulosa y su utilización como material de refuerzo en una matriz de policaprolactona. Se obtuvieron whiskers de celulosa a partir de pasta blanqueada. La adición en una matriz de policaprolactona produjo materiales compuestos con propiedades mecánicas superiores a la matriz, con buena dispersión de los whiskers. 3. Obtención de fibras de celulosa bacterial y nanofibras de celulosa, aislamiento y utilización sobre una matriz de polivinil alcohol. Se obtuvo celulosa bacterial a partir de la bacteria Gluconacetobacter xylinum. Además se fabricaron nanofibras de celulosa a partir eucalipto blanqueado. La celulosa bacterial como material de refuerzo no produjo importantes mejoras en las propiedades mecánicas de la matriz; en cambio se observaron mejoras destacables con la nanofibra como refuerzo.

Stone-ground wood pulp-reinforced polypropylene composites: water uptake and thermal properties

Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC

The suitability of steam exploded vitis vinifera and alkaline lignin for the manufacture of fiberboard

The main objective of this study was to explore the suitability of Vitis vinifera as a raw material and alkaline lignin as a natural binder for fiberboard manufacturing. In the first step, Vitis vinifera was steam- exploded through a thermo-mechanical vapor process in a batch reactor, and the obtained pulp was dried, ground, and pressed to produce the boards. The effects of pretreatment factors and pressing conditions on the chemical composition of the fibers and the physico-mechanical properties of binderless fiberboards were evaluated, and the conditions that optimize these properties were found. A response surface method based on a central composite design and multiple-response optimization was used. The variables studied and their respective variation ranges were: pretreatment temperature (Tr: 190-210ºC), pretreatment time (tr: 5-10 min), pressing temperature (Tp: 190-210ºC), pressing pressure (Pp: 8-16MPa), and pressing time (tp: 3-7min). The results of the optimization step show that binderless fiberboards have good water resistance and weaker mechanical properties. In the second step, fiberboards based on alkaline lignin and Vitis vinifera pulp produced at the optimal conditions determined for binderless fiberboards were prepared and their physico-mechanical properties were tested. Our results show that the addition of about 15% alkaline lignin leads to the production of fiberboards that fully meet the requirements of the relevant standard specifications

Clinical picture of the amyloid arthropathy in patients with chronic renal failure maintained on haemodialysis using cellulose membranes.

The clinical picture of 15 patients (10 male, five female) with amyloid arthropathy secondary to chronic renal failure treated with haemodialysis has been studied. The average period of haemodialysis was 10.8 years. Joint symptoms appeared between three and 13 years after starting haemodialysis. No patient had renal amyloidosis. Early symptoms were varied and often overlapped: knee swelling (seven patients), painful and stiff shoulders (seven), and carpal tunnel syndrome (six) were the most prominent. Follow up showed extension to other joints. Joint effusions were generally of the non-inflammatory type. Radiologically, geodes and erosions of variable sizes were seen in the affected joints, which can develop into a destructive arthropathy. Amyloid was found in abdominal fat in three of the 12 patients on whom a needle aspiration was performed. Four of 12 patients showed changes compatible with amyloid infiltration in the echocardiogram. One patient had amyloid in the gastric muscular layer, another in the colon mucus, and two of four in rectal biopsy specimens. Amyloid deposits showed the presence of beta 2 microglobulin in 10 patients. The clinical and radiological picture was similar to the amyloid arthropathy associated with multiple myeloma. These patients can develop systemic amyloidosis.

Clinical picture of the amyloid arthropathy in patients with chronic renal failure maintained on haemodialysis using cellulose membranes.

The clinical picture of 15 patients (10 male, five female) with amyloid arthropathy secondary to chronic renal failure treated with haemodialysis has been studied. The average period of haemodialysis was 10.8 years. Joint symptoms appeared between three and 13 years after starting haemodialysis. No patient had renal amyloidosis. Early symptoms were varied and often overlapped: knee swelling (seven patients), painful and stiff shoulders (seven), and carpal tunnel syndrome (six) were the most prominent. Follow up showed extension to other joints. Joint effusions were generally of the non-inflammatory type. Radiologically, geodes and erosions of variable sizes were seen in the affected joints, which can develop into a destructive arthropathy. Amyloid was found in abdominal fat in three of the 12 patients on whom a needle aspiration was performed. Four of 12 patients showed changes compatible with amyloid infiltration in the echocardiogram. One patient had amyloid in the gastric muscular layer, another in the colon mucus, and two of four in rectal biopsy specimens. Amyloid deposits showed the presence of beta 2 microglobulin in 10 patients. The clinical and radiological picture was similar to the amyloid arthropathy associated with multiple myeloma. These patients can develop systemic amyloidosis.