Analog Modelling of N-S anticlines of the External Sierras (Jaca basin, Southern Pyrenees)

Report for the scientific sojourn carried out at the Uppsala Universitet, Sweden, from April to July the 2007. Two series of analogue models are used to explore ductile-frictional contrasts of the basal décollement in the development of oblique and transverse structures simultaneously to thin-skinned shortening. These models simulate the evolution of the Central External Sierras (Southern Pyrenees, Spain), which constitute the frontal emerging part of the southernmost Pyrenean thrust sheet. They are characterized by the presence of transverse N-S to NW-SE anticlines, which are perpendicular to the Pyrenean structural trend and developed in the hangingwall of the Santo Domingo thrust system, detaching on an unevenly distributed Triassic materials (evaporitic-dolomitic interfingerings). Model setup performs a décollement made by three patches of silicone neighbouring pure brittle sand. Model series A test the thickness ratio between overburden and décollement. Model series B test the width of frictional detachment areas. Model results show how deformation reaches further in areas detached on ductile layer whereas frictional décollement areas assimilate the strain by means of an additional uplift. This replicates the structural style of Central External Sierras: higher structural relief of N-S anticlines with regard to orogen-parallel structures, absence of a representative ductile décollement in the core, tilting towards the orogen and foreland-side closure not thrusted by the frontal emerging South-Pyrenean thrust.

Analog circuit for real-time computation of respiratory mechanical impedance in sleep studies

The aim of this work was to develop a low-cost circuit for real-time analog computation of the respiratory mechanical impedance in sleep studies. The practical performance of the circuit was tested in six patients with obstructive sleep apnea. The impedance signal provided by the analog circuit was compared with the impedance calculated simultaneously with a conventional computerized system. We concluded that the low-cost analog circuit developed could be a useful tool for facilitating the real-time assessment of airway obstruction in routine sleep studies.

Decay of unstable states in the presence of colored noise and random initial conditions. II. Analog experiments and digital simulations

The decay of an unstable state under the influence of external colored noise has been studied by means of analog experiments and digital simulations. For both fixed and random initial conditions, the time evolution of the second moment ¿x2(t)¿ of the system variable was determined and then used to evaluate the nonlinear relaxation time. The results obtained are found to be in excellent agreement with the theoretical predictions of the immediately preceding paper [Casademunt, Jiménez-Aquino, and Sancho, Phys. Rev. A 40, 5905 (1989)].

Analog circuit for real-time computation of respiratory mechanical impedance in sleep studies

The aim of this work was to develop a low-cost circuit for real-time analog computation of the respiratory mechanical impedance in sleep studies. The practical performance of the circuit was tested in six patients with obstructive sleep apnea. The impedance signal provided by the analog circuit was compared with the impedance calculated simultaneously with a conventional computerized system. We concluded that the low-cost analog circuit developed could be a useful tool for facilitating the real-time assessment of airway obstruction in routine sleep studies.

The curcumin analog DM-1 induces apoptotic cell death in melanoma

The main difficulty in the successful treatment of metastatic melanoma is that this type of cancer is known to be resistant to chemotherapy. Chemotherapy remains the treatment of choice, and dacarbazine (DTIC) is the best standard treatment. The DM-1 compound is a curcumin analog that possesses several curcumin characteristics, such as antiproliferative, antitumor, and antimetastatic properties. The objective of this study was to evaluate the signaling pathways involved in melanoma cell death after treatment with DM-1 compared to the standard agent for melanoma treatment, DTIC. Cell death was evaluated by flow cytometry for annexin V and iodide propide, cleaved caspase 8, and TNF-R1 expression. Hoechst 33342 staining was evaluated by fluorescent microscopy; lipid peroxidation and cell viability (MTT) were evaluated by colorimetric assays. The antiproliferative effects of the drugs were evaluated by flow cytometry for cyclin D1 and Ki67 expression. Mice bearing B16F10 melanoma were treated with DTIC, DM-1, or both therapies. DM-1 induced significant apoptosis as indicated by the presence of cleaved caspase 8 and an increase in TNF-R1 expression in melanoma cells. Furthermore, DM-1 had antiproliferative effects in this the same cell line. DTIC caused cell death primarily by necrosis, and a smaller melanoma cell population underwent apoptosis. DTIC induced oxidative stress and several physiological changes in normal melanocytes, whereas DM-1 did not significantly affect the normal cells. DM-1 antitumor therapy in vivo showed tumor burden decrease with DM-1 monotherapy or in combination with DTIC, besides survival rate increase. Altogether, these data confirm DM-1 as a chemotherapeutic agent with effective tumor control properties and a lower incidence of side effects in normal cells compared to DTIC.

Monitor EMG con conexión inalámbrica

El sistema desarrollado en este trabajo permite la detección de fatiga del músculo de un paciente. Las señales electromiográficas generadas por el músculo son detectadas mediante electrodos superficiales, que sirven de entrada al circuito hacia los diferentes canales de entrada. Tras una primera etapa de amplificación, las señales son filtradas por un filtro pasabanda. Las señales acondicionadas se digitalizan mediante un conversor analógico digital que está conectado a un microcontrolador. Éste establece la comunicación con el PC enviándole los datos a través del puerto serie. Finalmente, mediante un programa implementado en Labview se procesan los datos y se determina la existencia o no de fatiga muscular.

Estudi per a un sistema de mesura de pes per a marmota alpina

Aquest projecte tracta sobre la viabilitat de la construcció d’un sistema per al seguiment del pes d’una població de marmotes en alta muntanya. Bàsicament, es construeix una bàscula amb un sensor de força i un sensor de temperatura. Aquestes sortides analògiques es connecten a un microcontrolador ATmega8 que, mitjançant un algorisme desenvolupat en aquest projecte, està contínuament en escolta fins a detectar un canvi sobtat en el pes. Aleshores les dades s’enregistren i es guarden en una memòria SRAM per a, posteriorment, poder ser descarregades a un ordinador i analitzades per un programa que s’ha creat per a tal finalitat.

Consolidació de la Plataforma COMalaWEB com a eina Web d'autoaprenentatge per a l'EEES

La plataforma d’e-learning: COMalaWEB és una eina multimedia de suport a l’estudi, l’experimentació i l’adquisició de tècniques d’autoaprenentatge. COMalaWEB s’ofereix com a punt de trobada entre estudiants, professors i altres professionals relacionats amb el mon de les telecomunicacions i/o de la docència universitària. Mitjançant el present projecte s’ha dut a terme la consolidació de la plataforma COMalaWEB com a eina WWW d'autoaprenentatge per a l'EEES (Estudis de Bachelor i de Màster): Dins de la plataforma s’hi ha integrat un Laboratori Virtual per a comunicacions analògiques i digitals (LaViCAD) que ofereix activitats experimentals amb un gran ventall de possibilitats que van des de les demostracions teòriques fins a l’emulació de sistemes de comunicacions quotidians com per exemple la televisió digital o el sistema Wifi dels sistemes WLAN. L’altre gran component de la plataforma es la base de dades de continguts empaquetada en unitats bàsiques anomenades objectes de coneixement, organitzada en cursos, integren tant continguts teòrics com un conjunt d’exercicis proposats per a aprofundir cadascun dels temes tractats. Amb l’actual projecte s’ha treballat en les següents línies d’actuació: - Integració dels simuladors del laboratori LAVICAD a la plataforma d’autoaprenentatge. - Creació de base de dades de recursos docents basats en paquets SCORM per a oferir materials docents de tipus teòric i col·leccions d’exercicis resolts en el marc de les diferents assignatures participants en el projecte. - Creació de base de dades de tipus qüestionari per a oferir exercicis a treballar en el marc de les diferents assignatures participants en el projecte. - Inserció de metodologies docents basades en els anteriors recursos en diferents assignatures d’estudis d’enginyeria i de màster.

Design of Novel Frequency Generation Circuit with Application to Ultra-Wideband Distributed Oscillators

Given the urgence of a new paradigm in wireless digital trasmission which should allow for higher bit rate, lower latency and tigher delay constaints, it has been proposed to investigate the fundamental building blocks that at the circuital/device level, will boost the change towards a more efficient network architecture, with high capacity, higher bandwidth and a more satisfactory end user experience. At the core of each transciever, there are inherently analog devices capable of providing the carrier signal, the oscillators. It is strongly believed that many limitations in today's communication protocols, could be relieved by permitting high carrier frequency radio transmission, and having some degree of reconfigurability. This led us to studying distributed oscillator architectures which work in the microwave range and possess wideband tuning capability. As microvave oscillators are essentially nonlinear devices, a full nonlinear analyis, synthesis, and optimization had to be considered for their implementation. Consequently, all the most used nonlinear numerical techniques in commercial EDA software had been reviewed. An application of all the aforementioned techniques has been shown, considering a systems of three coupled oscillator ("triple push" oscillator) in which the stability of the various oscillating modes has been studied. Provided that a certain phase distribution is maintained among the oscillating elements, this topology permits a rise in the output power of the third harmonic; nevertheless due to circuit simmetry, "unwanted" oscillating modes coexist with the intenteded one. Starting with the necessary background on distributed amplification and distributed oscillator theory, the design of a four stage reverse mode distributed voltage controlled oscillator (DVCO) using lumped elments has been presented. All the design steps have been reported and for the first time a method for an optimized design with reduced variations in the output power has been presented. Ongoing work is devoted to model a wideband DVCO and to implement a frequency divider.

The Molecular Basis for Antimicrobial Activity of Pore-Forming Cyclic Peptides

The mechanism of action of antimicrobial peptides is, to our knowledge, still poorly understood. To probe the biophysical characteristics that confer activity, we present here a molecular-dynamics and biophysical study of a cyclic antimicrobial peptide and its inactive linear analog. In the simulations, the cyclic peptide caused large perturbations in the bilayer and cooperatively opened a disordered toroidal pore, 1–2 nm in diameter. Electrophysiology measurements confirm discrete poration events of comparable size. We also show that lysine residues aligning parallel to each other in the cyclic but not linear peptide are crucial for function. By employing dual-color fluorescence burst analysis, we show that both peptides are able to fuse/aggregate liposomes but only the cyclic peptide is able to porate them. The results provide detailed insight on the molecular basis of activity of cyclic antimicrobial peptides

Information-theoretical derivation of an extended thermodynamical description of radiative systems

A radiative equation of the Cattaneo–Vernotte type is derived from information theory and the radiative transfer equation. The equation thus derived is a radiative analog of the equation that is used for the description of hyperbolic heat conduction. It is shown, without recourse to any phenomenological assumption, that radiative transfer may be included in a natural way in the framework of extendedirreversible thermodynamics

Strategies for sequential prediction of stationary time series

We present simple procedures for the prediction of a real valued sequence. The algorithms are based on a combinationof several simple predictors. We show that if the sequence is a realization of a bounded stationary and ergodic random process then the average of squared errors converges, almost surely, to that of the optimum, given by the Bayes predictor. We offer an analog result for the prediction of stationary gaussian processes.

Sistema d'adquisició de temperatures de 2 canals via R.F.

Poder mesurar i enregistrar diferents tipus de magnituds com pressió, força, temperatura etc. s’ha convertit en una necessitat per moltes aplicacions actuals. Aquestes magnituds poden tenir procedències molt diverses, tals com l’entorn, o poden ser generades per sistemes mecànics, elèctrics, etc. Per tal de poder adquirir aquestes magnituds, s’utilitzen els sistemes d’adquisició de dades. Aquests sistemes, prenen mostres analògiques del món real, i les transformen en dades digitals que poden ser manipulades per un sistema electrònic. Pràcticament qualsevol magnitud es pot mesurar utilitzant el sensor adient. Una magnitud molt utilitzada en sistemes d’adquisició de dades, és la temperatura. Els sistemes d’adquisició de temperatures estan molt generalitzats, i podem trobar-los com a sistemes, on l’objectiu és mostrar les dades adquirides, o podem trobar-los formant part de sistemes de control, aportant uns inputs necessaris per el seu correcte funcionament, garantir-ne l’estabilitat, seguretat etc. Aquest projecte, promogut per l’empresa Elausa, s’encarregarà d’adquirir, el senyal d’entrada de 2 Termoparells. Aquests mesuraran temperatures de circuits electrònics, que es trobaran dintre la càmera climàtica de Elausa, sotmesos a diferents condicions de temperatura, per tal de rebre l’homologació del circuit. El sistema haurà de poder mostrar les dades adquirides en temps real, i emmagatzemar-les en un PC que estarà ubicat en una oficina, situada a uns 30 m de distància de la sala on es farà el test. El sistema constarà d’un circuit electrònic que adquirirà, i condicionarà el senyal de sortida dels termoparells, per adaptar-lo a la tensió d’entrada d’un convertidor analògic digital, del microcontrolador integrat en aquesta placa. Seguidament aquesta informació, s’enviarà a través d’un mòdul transmissor de radiofreqüència, cap al PC on es visualitzaran les dades adquirides. Els objectius plantejats són els següents: - Dissenyar el circuit electrònic d’adquisició i condicionament del senyal. - Dissenyar, fabricar i muntar el circuit imprès de la placa d’adquisició. - Realitzar el programa de control del microcontrolador. - Realitzar el programa per presentar i desar les dades en un PC. - El sistema ha d’adquirir 2 temperatures, a través de Termoparells amb un rang d’entrada de -40ºC a +240ºC - S’ha de transmetre les dades via R.F. Els resultats del projecte han estat satisfactoris i s’han complert els objectius plantejats.

A reusable smart interface for gas sensor resistance measurement

The advances of the semiconductor industry enable microelectromechanical systems sensors, signal conditioning logic and network access to be integrated into a smart sensor node. In this framework, a mixed-mode interface circuit for monolithically integrated gas sensor arrays was developed with high-level design techniques. This interface system includes analog electronics for inspection of up to four sensor arrays and digital logic for smart control and data communication. Although different design methodologies were used in the conception of the complete circuit, high-level synthesis tools and methodologies were crucial in speeding up the whole design cycle, enhancing reusability for future applications and producing a flexible and robust component.

Continuous phase shift of sinusoidal signals using injection locked oscillators

This work presents an alternative to generate continuous phase shift of sinusoidal signals based on the use of super harmonic injection locked oscillators (ILO). The proposed circuit is a second harmonic ILO with varactor diodes as tuning elements. In the locking state, by changing the varactor bias, a phase shift instead of a frequency shift is observed at the oscillator output. By combining two of these circuits, relative phases up to 90 could be achieved. Two prototypes of the circuit have been implemented and tested, a hybrid version working in the range of 200-300 MHz and a multichip module (MCM) version covering the 900¿1000 MHz band.