Lattice-dynamical study of the premartensitic state of the Cu-Al-Be alloys

Neutron-scattering techniques have been used to study the premartensitic state of a family of Cu-Al-Be alloys, which transform from the bcc phase to an 18R martensitic structure. We find that the phonon modes of the TA2[110] branch have very low energies with anomalous temperature dependence. A slight anomaly at q=2/3 was observed; this anomaly, however, does not change significantly with temperature. No elastic peaks, related to the martensite structure, were found in the premartensitic state of these alloys. The results are compared with measurements, performed under the same instrumental conditions, on two Cu-Al-Ni and a Cu-Zn-Al martensitic alloy.

High-pressure ultrasonic study of vibrational anharmonicity in bcc Cu-Al-Be alloys

To quantify the vibrational anharmonicity of the long-wavelength acoustic modes of bcc Cu74.1Al23.1Be2.8 near its martensitic transition temperature Ms (261 K), the hydrostatic pressure derivatives (¿CIJ/¿P)P=0 of the elastic stiffness moduli have been measured. The Grüneisen parameters at 268 K (just above Ms), especially of longitudinal modes, which become smaller than those of the shear modes, are quite different from those at 295 K: the anharmonicity changes markedly in the vicinity of the transition. Similar trends are noted for Cu66.5Al12.7Zn20.8. Experimental data near Ms are used to estimate cubic invariants in the strain order parameters in a Landau formalism.

Elastic constants of bcc Cu-Al-Ni alloys

We have measured the adiabatic elastic constants of two Cu-Al-Ni martensitic alloys using ultrasonic methods and we have compared the results to recent neutron-scattering experiments. It is shown that the elastic behavior of Cu-Al-Ni alloys follows the same trends exhibited by other Cu-based alloys; in particular, the TA2 long-wavelength acoustic modes are softer than all other modes.

Disorder-induced critical phenomena in magnetically glassy Cu-Al-Mn alloys

Measurements of magnetic hysteresis loops in Cu-Al-Mn alloys of different Mn content at low temperatures are presented. The loops are smooth and continuous above a certain temperature, but exhibit a magnetization discontinuity below that temperature. Scaling analysis suggest that this system displays a disorder-induced phase transition line. Measurements allow one to determine the critical exponents ß=0.03±0.01 and ß¿=0.4±0.1, which coincide with those reported recently in a different system, thus supporting the existence of universality for disorder-induced critical points.

Significado sedimentológico de los niveles con Assilinas de la Formación Armancies (Eoceno medio) y sus equivalentes laterales

In this paper we show some sedimentological characteristics of Assilina beds from Armancies Fm. (middle Eocene) and their lateral equivalents that let us to remark some aspects of their genesis. We arrive to the conclusion that, in occidental sector (Bagá-Campdevanol), ‘las barras de Assilinas’ from the Armancies Fm. are grain flow channels, first sedimented at W of Terrades and after slided, from E to W in a turbidite basin, without any coarse clastic

Monitoratge remot d'esdeveniments per al control i supervisió utilitzant "System on chip" i "w-USB"

Aquesta memòria descriu el procés de desenvolupament d'un projecte que consisteix en un conjunt de hardware, “PSoC” (Programmable System on Chip), i un software, C#, mitjançant els quals s'automatitza la gestió de comandes a les taules d'un restaurant. A cada taula trobem un aparell anomenat “WaiterClient”, a través del qual els clients sol·liciten l'atenció d'un cambrer. Aquest hardware té una pantalla on es mostrarà informació i un conjunt de polsadors per demanar. Per una altra banda, trobem un altre aparell, “WaiterServidor”, encarregat de rebre els senyals enviats per wireless des dels “WaiterClients” que hi ha a cada taula. Un cop rebudes, les transmet a un ordinador central per cable sèrie RS-232.

On the stability of the bcc phase in Cu-Al-Mn shape memory alloys

Measurements of the entropy change at the martensitic transition of two composition-related sets of Cu-Al-Mn shape-memory alloys are reported. It is found that most of the entropy change has a vibrational origin, and depends only on the particular close-packed structure of the low-temperature phase. Using data from the literature for other Cu-based alloys, this result is shown to be general. In addition, it is shown that the martensitic structure changes from 18R to 2H when the ratio of conduction electrons per atom reaches the same value as the eutectoid point in the equilibrium phase diagram. This finding indicates that the structure of the metastable low-temperature phase is reminiscent of the equilibrium structure.

Magnetoelasticity and magnetoresistance in Cu-Al-Mn shape-memory alloys

We study the effect of a magnetic field on the martensitic transition of a Cu-Al-Mn shape-memory alloy. The martensitic transition has been studied through resistance measurements under applied magnetic fields ranging from 0 to 50 kOe. Negative magnetoresistance showing an almost linear dependence with the square of the magnetization has been observed. This magnetoresistive effect is associated with the existence of small ferromagnetic Mn-clusters. Its strength and thermal dependence is different in both phases. The martensitic transition temperature is slightly increased and its spread in temperature significantly reduced upon increasing the field. These results show the existence of magnetoelastic coupling, which favors the nucleation of those martensitic variants with the easy magnetization axis aligned with the field.

State equation for shape-memory alloys. Aplication to Cu-Zn-Al

We deal with the hysteretic behavior of partial cycles in the two¿phase region associated with the martensitic transformation of shape¿memory alloys. We consider the problem from a thermodynamic point of view and adopt a local equilibrium formalism, based on the idea of thermoelastic balance, from which a formal writing follows a state equation for the material in terms of its temperature T, external applied stress ¿, and transformed volume fraction x. To describe the striking memory properties exhibited by partial transformation cycles, state variables (x,¿,T) corresponding to the current state of the system have to be supplemented with variables (x,¿,T) corresponding to points where the transformation control parameter (¿¿ and/or T) had reached a maximum or a minimum in the previous thermodynamic history of the system. We restrict our study to simple partial cycles resulting from a single maximum or minimum of the control parameter. Several common features displayed by such partial cycles and repeatedly observed in experiments lead to a set of analytic restrictions, listed explicitly in the paper, to be verified by the dissipative term of the state equation, responsible for hysteresis. Finally, using calorimetric data of thermally induced partial cycles through the martensitic transformation in a Cu¿Zn¿Al alloy, we have fitted a given functional form of the dissipative term consistent with the analytic restrictions mentioned above.

Magnetoelasticity and magnetoresistance in Cu-Al-Mn shape-memory alloys

We study the effect of a magnetic field on the martensitic transition of a Cu-Al-Mn shape-memory alloy. The martensitic transition has been studied through resistance measurements under applied magnetic fields ranging from 0 to 50 kOe. Negative magnetoresistance showing an almost linear dependence with the square of the magnetization has been observed. This magnetoresistive effect is associated with the existence of small ferromagnetic Mn-clusters. Its strength and thermal dependence is different in both phases. The martensitic transition temperature is slightly increased and its spread in temperature significantly reduced upon increasing the field. These results show the existence of magnetoelastic coupling, which favors the nucleation of those martensitic variants with the easy magnetization axis aligned with the field.

Atomic Ordering and Martensitic Transitions in Cu-Zn-Al Shape Memory Alloys

We present results from both, calorimetric and dilatometric studies of the isothermal ordering process taking place in a Cu-Zn-Al shape memory alloy after quenches from Tq temperatures ranging from 350 K to 1200 K. The dissipated energy and the length variations of the system are obtained during the process. The change of these quantities in the whole process have been compared with the difference [MATH] between Ms, measured after the relaxation and Ms measured just after the quench. We obtain that these three quantities present, as a function of Tq, the same qualitative behaviour. These changes are then associated with changes of the L21 ordering after the quench in the system. The relaxational process does not follow a single exponential decay. Instead, a continuous slowing down is observed. A relaxation time [MATH] has been defined to characterize the relaxation rate. We show that [MATH] depends on both the annealing and the quenching (Tq [MATH] 800 K) temperatures through an Arrhenius law.

Comparativa de equipos de síntesis mecánica : aleaciones de base Al-Cu y Fe-Ni

La síntesis mecánica es un proceso basado en la molturación de una mezcla de polvosometida a altas energías que se producen por los choques entre las partículas y lasbolas de un micromolino, entre las partículas y las paredes del recipiente y entre lasmismas partículas. Los dos procesos involucrados en el proceso de síntesis mecánicason la soldadura en frío y la fractura.El proyecto que se presenta es una continuación de los diferentes estudios realizadosen el departamento de Recerca de Materials i Termodinàmica de la Universidad deGirona sobre el proceso de aleado mecánico, en especial del proyecto de Ivan Darnés(Abril 2005) donde se realizaba un estudio comparativo de los micromolinosPulverisette 7 (P7) y SPEX8000 a partir de dos aleaciones en polvo de base Fe.El presente proyecto tiene como objetivo principal realizar nuevamente unacomparación de los equipos P7 y SPEX8000, pero utilizando otras mezclas de polvoiniciales y modificando los parámetros del proceso. Para tal comparación se estudiaránlas muestras obtenidas a nivel estructural, térmico y morfológico