Response of the Thermal Conductivity as a Function of Water Content of a Burnt Mediterranean Loam Soil

The purpose of this research is to explore the variability on the soil thermal conductivity -λ- after a prescribe fire, and to assess the effects of the ashes on the heat transfer once it"s were incorporated into the soil matrix. Sampling plot was located in the Montgrí Massif (NE of Spain). A set of 42 soil samples between surface and 5 cm depth was collected before and after the fire. To characterize the soil chemical and physical variables were analyzed. To determine the vari-ability on the soil λ a dry-out curve per scenario (before and after fire) was determined. SoilRho® method based on ASTM D-5334-08 which was validated by LabFerrer was used. Soil thermal conductivity has shown changes in their values. Indeed, in all moisture scenarios the values of soil λ decreased after soil was burnt. The critical point in the rela-tionship ϴ (λ) for the soil after fire which always was stronger than soil before to be burnt. Soil with"white" ashes showed a high thermal conductivity. An X-Ray diffractometry analysis allowed to clarify and to verify these results. To sum up, we could say that thermal conductivity presents changes when the scenario changes, i.e. before and after to be burnt. On the other hand, the volume of ashes incorporated on the soil increased the differences between no burnt and burnt soil, showing even some improvements on the heat transfer when water content started to govern the process.

Thermal increment due to ErCr: YSGG and CO2 laser irradiation of different implant surfaces. A pilot study

Objective: An evaluation and comparison is made of the thermal increment at different implant surfaces during irradiation with CO2 and ErCr:YSGG lasers. Study design: Five threaded and impacted implants with four types of surfaces were inserted in an adult pig rib: two implants with a hydroxyapatite surface (HA)(impacted and threaded, respectively), a machined titanium surface implant (TI mach), a titanium plasma spray surface implant (TPS), and a sandblasted, acid-etched surface implant (SBAE). A 0.5-mm diameter bone defect was made in the implant apical zone, and a type-K thermocouple (Termopar)® was placed in contact with the implant. The implants were irradiated in the coronal zone of each implant with a CO2 (4 W continuous mode) and an ErCr:YSGG laser (1.5 W, pulsed mode) first without and then with refrigeration. The temperature variations at the implant apical surface were recorded. Results: An apical temperature increase was recorded in all cases during CO2 and ErCr:YSGG laser irradiation without refrigeration. However, when the ErCr:YSGG was used with a water spray, a decrease in temperature was observed in all implants. The acid-etched and sandblasted surfaces were those most affected by the thermal changes. Conclusions: The ErCr:YSGG laser with a water spray applied to the sealing cap or coronal zone of the implants does not generate thermal increments in the apical surface capable of adversely affecting osseointegration and the integrity of the peri-implant bone tissue

Current Sheet Regulation of Solar Near-Relativistic Electron Injection Histories

We present a sample of three large near-relativistic (>50 keV) electron events observed in 2001 by both the ACE and the Ulysses spacecraft, when Ulysses was at high-northern latitudes (>60°) and close to 2 AU. Despite the large latitudinal distance between the two spacecraft, electrons injected near the Sun reached both heliospheric locations. All three events were associated with large solar flares, strong decametric type II radio bursts and accompanied by wide (>212°) and fast (>1400 km s-1) coronal mass ejections (CMEs). We use advanced interplanetary transport simulations and make use of the directional intensities observed in situ by the spacecraft to infer the electron injection profile close to the Sun and the interplanetary transport conditions at both low and high latitudes. For the three selected events, we find similar interplanetary transport conditions at different heliolatitudes for a given event, with values of the mean free path ranging from 0.04 AU to 0.27 AU. We find differences in the injection profiles inferred for each spacecraft. We investigate the role that sector boundaries of the heliospheric current sheet (HCS) have on determining the characteristics of the electron injection profiles. Extended injection profiles, associated with coronal shocks, are found if the magnetic footpoints of the spacecraft lay in the same magnetic sector as the associated flare, while intermittent sparse injection episodes appear when the spacecraft footpoints are in the opposite sector or a wrap in the HCS bounded the CME structure.

Identification of metabolites and thermal transformation products of quinolones in raw cow milk by liquid chromatography coupled to high resolution mass spectrometry

The presence of residues of antibiotics, metabolites, and thermal transformation products (TPs), produced during thermal treatment to eliminate pathogenic microorganisms in milk, could represent a risk for people. Cow"s milk samples spiked with enrofloxacin (ENR), ciprofloxacin (CIP), difloxacin (DIF), and sarafloxacin (SAR) and milk samples from cows medicated with ENR were submitted to several thermal treatments. The milk samples were analyzed by liquid chromatography-mass spectrometry (LC-MS) to find and identify TPs and metabolites. In this work, 27 TPs of 4 quinolones and 24 metabolites of ENR were found. Some of these compounds had been reported previously, but others were characterized for the first time, including lactose-conjugated CIP, the formamidation reaction for CIP and SAR, and hydroxylation or ketone formation to produce three different isomers for all quinolones studied.

Identification of metabolites and thermal transformation products of quinolones in raw cow milk by liquid chromatography coupled to high resolution mass spectrometry.

The presence of residues of antibiotics, metabolites, and thermal transformation products (TPs), produced during thermal treatment to eliminate pathogenic microorganisms in milk, could represent a risk for people. Cow"s milk samples spiked with enrofloxacin (ENR), ciprofloxacin (CIP), difloxacin (DIF), and sarafloxacin (SAR) and milk samples from cows medicated with ENR were submitted to several thermal treatments. The milk samples were analyzed by liquid chromatography-mass spectrometry (LC-MS) to find and identify TPs and metabolites. In this work, 27 TPs of 4 quinolones and 24 metabolites of ENR were found. Some of these compounds had been reported previously, but others were characterized for the first time, including lactose-conjugated CIP, the formamidation reaction for CIP and SAR, and hydroxylation or ketone formation to produce three different isomers for all quinolones studied.

Capillary thermal desorption unit for near real-time analysis of VOCs at sub-trace levels. Application to the analysis of environmental air contamination and breath samples

A capillary microtrap thermal desorption module is developed for near real-time analysis of volatile organic compounds (VOCs) at sub-ppbv levels in air samples. The device allows the direct injection of the thermally desorbed VOCs into a chromatographic column. It does not use a second cryotrap to focalize the adsorbed compounds before entering the separation column so reducing the formation of artifacts. The connection of the microtrap to a GC–MS allows the quantitative determination of VOCs in less than 40 min with detection limits of between 5 and 10 pptv (25 °C and 760 mmHg), which correspond to 19–43 ng m−3, using sampling volumes of 775 cm3. The microtrap is applied to the analysis of environmental air contamination in different laboratories of our faculty. The results obtained indicate that most volatile compounds are easily diffused through the air and that they also may contaminate the surrounding areas when the habitual safety precautions (e.g., working under fume hoods) are used during the manipulation of solvents. The application of the microtrap to the analysis of VOCs in breath samples suggest that 2,5-dimethylfuran may be a strong indicator of a person's smoking status

Inbreeding and thermal adaptation in Drosophila subobscura

Using a well-adapted Drosophila subobscura population (Avala, Serbia), a drastic experiment of inbreeding was carried out to assess whether the expected level of homozygosity could be reached or if other evolutionary forces affected the process. In general, no significant changes of inversion (or arrangement) frequencies were detected after 12 brother sister mating generations. Furthermore, no significant differences were obtained between observed and expected (under the inbreeding model) karyotypic frequencies. Thus, these results seemed to indicate that the main evolutionary factor in the experiment was inbreeding. However, in the G12 generation, complete chromosomal fixation was reached only in two out of the eight final inbred lines. In these lines, the chromosomal compositions were difficult to interpret, but they could be likely a consequence of adaptation to particular laboratory conditions (constant 18 °C, food, light period, etc.). Finally, in a second experiment, the inbred lines presented higher fertility at 18 °C than at 13 °C. Also, there was a significant line effect on fertility: inbred line number 6 (A1, J1, U1+2; U1+2+6, E8, and O3+4+7) presented the highest values, which maybe the result of an adaptation to laboratory conditions. Thus, the results obtained in our experiments reflect the adaptive potential of D. subobscura inversions.

Non-thermal emission from microquasar/ISM interaction

Context. The interaction of microquasar jets with their environment can produce non-thermal radiation as in the case of extragalactic outflows impacting on their surroundings. Significant observational evidence of jet/medium interaction in galactic microquasars has been collected in the past few years, although little theoretical work has been done regarding the resulting non-thermal emission. Aims. In this work, we investigate the non-thermal emission produced in the interaction between microquasar jets and their environment, and the physical conditions for its production. Methods. We developed an analytical model based on those successfully applied to extragalactic sources. The jet is taken to be a supersonic and mildly relativistic hydrodynamical outflow. We focus on the jet/shocked medium structure in its adiabatic phase, and assume that it grows in a self-similar way. We calculate the fluxes and spectra of the radiation produced via synchrotron, inverse Compton, and relativistic bremsstrahlung processes by electrons accelerated in strong shocks. A hydrodynamical simulation is also performed to investigate further the jet interaction with the environment and check the physical parameters used in the analytical model. Results. For reasonable values of the magnetic field, and using typical values of the external matter density, the non-thermal particles could produce significant amounts of radiation at different wavelengths, although they do not cool primarily radiatively, but by adiabatic losses. The physical conditions of the analytical jet/medium interaction model are consistent with those found in the hydrodynamical simulation. Conclusions. Microquasar jet termination regions could be detectable at radio wavelengths for current instruments sensitive to ~arcminute scales. At X-ray energies, the expected luminosities are moderate, although the emitter is more compact than the radio one. The source may be detectable by XMM-Newton or Chandra, with 1-10 arcsec of angular resolution. The radiation at gamma-ray energies may be within the detection limits of the next generation of satellite and ground-based instruments.

Effects of solar activity and climate variability on large floods in Switzerland

The paper presents the variability of major floods in Switzerland for the period 1800-2008 from a summer index (INU). The index is constructed from the damage caused by flooding, with the aim of establishing the possible influence of the solar and climate variability on the major floods. The coincidence of flood-rich periods with those observed in other regions of different climate and fluvial regimes suggests that climate forcings and changes in the general circulation of the atmosphere are those who govern the appearance of these high-frequency temporal clusters.

A Method for Sky-Condition Classification from Ground-Based Solar Radiation Measurements

Identification of clouds from satellite images is now a routine task. Observation of clouds from the ground, however, is still needed to acquire a complete description of cloud conditions. Among the standard meteorologicalvariables, solar radiation is the most affected by cloud cover. In this note, a method for using global and diffuse solar radiation data to classify sky conditions into several classes is suggested. A classical maximum-likelihood method is applied for clustering data. The method is applied to a series of four years of solar radiation data and human cloud observations at a site in Catalonia, Spain. With these data, the accuracy of the solar radiation method as compared with human observations is 45% when nine classes of sky conditions are to be distinguished, and it grows significantly to almost 60% when samples are classified in only five different classes. Most errors are explained by limitations in the database; therefore, further work is under way with a more suitable database

Relaxation and derelaxation of pure and hydrogenated amorphous silicon during thermal annealing experiments

The structural relaxation of pure amorphous silicon (a-Si) and hydrogenated amorphous silicon (a-Si:H) materials, that occurs during thermal annealing experiments, has been analyzed by Raman spectroscopy and differential scanning calorimetry. Unlike a-Si, the heat evolved from a-Si:H cannot be explained by relaxation of the Si-Si network strain but it reveals a derelaxation of the bond angle strain. Since the state of relaxation after annealing is very similar for pure and hydrogenated materials, our results give strong experimental support to the predicted configurational gap between a-Si and crystalline silicon

Projecte executiu d'una instal·lació de climatització i control d'un habitatge unifamiliar

Moltes vegades l’usuari d’una instal•lació de climatització o calefacció, no dóna la suficient importància al sistema que l’hi ha de proporcionar un millor confort amb el màxim rendiment. Aquest confort és un factor determinant, entre molts d’altres, de la “qualitat de vida”. Mentre que el rendiment és un factor important a nivell econòmic i ecològic. Tot i tenir prevalença els aspectes d’estalvi energètic, aquests no impliquen haver de renunciar a un confort tèrmic i a un estalvi econòmic. Un dels aspectes que es centra el projecte és promoure l’ús racional de les fonts energètiques (solar, biomassa) per a la correcta climatització dels habitatges. El projecte es desenvolupa en l’àmbit domèstic, concretament correspon a un habitatge unifamiliar. Aquest està situat a la població de Roda de Ter, província de Barcelona. L’objectiu principal del projecte és l’elecció del sistema de climatització i el seu dimensionament, per tal de donar el màxim confort als usuaris que habitin a la vivenda. Criteris ambientals i eficients han estat objecte a considerar pel disseny constructiu de l’habitatge. Una de les mesures importants presses en el projecte, ha estat l’elecció de les diferents parts que formen la instal•lació de climatització. Es fa referència als aïllaments dels tancaments, el sistema solar de recolzament, equips de producció de fred i calor, entre d’altres. En el projecte, s’ha dut a terme un estudi dels diferents tancaments de l’habitatge, tot determinat per a cada un d’ells, el seu coeficient de transmissió tèrmica. Per seleccionar l’equipament més adequat s’ha partit de les condicions climatològiques del municipi de Roda de Ter i s’ha realitzat el càlcul de les necessitats tèrmiques de l’edifici. L’habitatge incorpora una instal•lació de captació solar tèrmica. Aquesta aportarà un suport energètic a tot el sistema de producció de calor, ja sigui per la producció d’aigua calenta sanitària com per el calefactat de la vivenda. La col•locació dels panells a la façana sud tindrà una doble funció: a més de proporcionar energia solar tèrmica, serviran d’elements de protecció solar en la temporada d’estiu. La caldera usada per donar recolzament tèrmic utilitzarà com a combustible el “pellet”. El “pellet” és un tipus de biomassa llenyosa que consta d’un derivat de la fusta en format granulat. Es defineix i es detalla el consum energètic en biomassa, electricitat i cost econòmic anual que ocasionarà la instal.lació dissenyada. El sistema de terra radiant adoptat permetrà el refrescament en èpoques estivals i el calefactat en èpoques hivernals. Aquest donarà el confort tèrmic necessari a cada estança de l’habitatge. En el projecte també es marquen les pautes bàsiques pel control de la instal•lació solar així com el control dels grups de bombament i la mescla d’aigua del terra radiant.

Construcció d'un refugi situat al terme municipal de Vallfogona de Ripollès, pensat com a final d'etapa per a rutes a cavall

Els negocis relacionats amb les activitats de lleure i els esports d’aventura actualment es troben en expansió, buscant majoritàriament el contacte amb la natura. Les rutes a cavall formen part del gran ventall d’opcions, per aquesta qüestió s’ha pensat en construir un refugi utilitzat com a final d’etapa per a rutes a cavall. En la major part del territori, la presència de població humana es manifesta en pobles, viles i ciutats, les quals disposes d’aigua sanitària, corrent elèctric i sistema de clavegueram. Per altra banda en les urbanitzacions o cases aïllades poder gaudir d’aquests serveis suposa una inversió econòmica elevada, que implica la utilització de sistemes alternatius. En el present projecte s’ha triat un emplaçament on portar a terme el final d’etapa amb una sèrie de requisits a complir : bosc a les proximitats, disposar d’un o varis accessos per a vehicles (transport del material d’intendència), tranquil•litat, bones vistes, i cobertura de telèfon mòbil. S’han acceptat les següents limitacions : no disposar de xarxa pública d’electricitat ni d’aigua. I s’han dimensionat les instal•lacions per a un màxim de dotze persones i els seus respectius cavalls. El principal objectiu del projecte és el dimensionament de les necessitats elèctriques, d’aigua i d’aiguacalenta sanitària en condicions autònomes, i utilitzant energies renovables. La valoració de les possibles solucions per condicionar les instal•lacions, i oferir una resposta eficient per la demanda. No és un objectiu específic del treball la potabilització de l’aigua ni el tractament dels residus produïts. S’han aprofitat els diferents desnivells que presenta l’emplaçament triat a l’hora de distribuir les instal•lacions, i s’ha utilitzat un antic cobert de dos pisos ja existent. Com a residència s’ha triat un model de casa prefabricada de muntanya. Com a sistema de subministrament elèctric, s’instal•laran plaques solars fotovoltaiques i un generador de corrent com a sistema auxiliar. La captació d’aigua s’efectuarà a partir d’un pou que es troba en el terreny i de la recollida d el’aigua pluvial, instal•lant dipòsits d’emmagatzemament d’aigua segons les necessitats. S’utilitzarà un equip de cloració per potabilitzar l’aigua de consum utilitzada a la residència. En la producció d’aigua calenta sanitària s’utilitzaran plaques solars tèrmiques i una caldera instantània de gas propà com a suport. Per cuinar s’ha triat una cuina de gas propà i una barbacoa que s’instal•larà a l’exterior. S’instal•larà una llar de foc amb recuperador d’aire a la residència i una fosa sèptica amb un sistema d’infiltració per poder abocar les aigües provinents de la residència. Els fems dels cavalls podran ser utilitzats com adob pel terreny.

Proyecto de ejecución para las obras de concesión de dominio público para la reforma y adecuación de la central térmica y de la red de saneamiento en un hospital de 350 camas

El Hospital Punta de Europa en Algeciras (Cádiz), centro sanitario del Servicio Andaluz de Salud, desea optimizar la gestión de sus instalaciones de generación de energía térmica (vapor, agua caliente sanitaria y agua caliente de calefacción) y adecuarlas a la normativa vigente así como la sustitución de bajantes del edificio, para lo cual sacará a concurso público la licitación para la concesión de dominio público de dichas instalaciones. Para definir el alcance y condiciones de la citada concesión, el Hospital Punta de Europa (Algeciras) del Servicio Andaluz de Salud ha solicitado a Pedro Alonso Martín el estudio para la reforma y adecuación de las instalaciones productoras de energía térmica del citado Hospital. El objetivo principal de este trabajo es hacer un estudio, propuesta y valoración de las actuaciones necesarias para la reforma y mejora de la explotación de las instalaciones generadoras de energía térmica y de la red saneamiento interior del Hospital Punta de Europa de Algeciras (Cádiz). Las actuales instalaciones de generación térmica consumidoras de energía del hospital dentro del alcance de este Proyecto son: Generación de vapor (lavandería y esterilización). Producción de agua caliente sanitaria (ACS). Producción de agua caliente de calefacción. La mayoría de los equipos productores de energía datan del año 1975, por lo que en la mayoría de los casos se ha cumplido su plazo de amortización y periodo de vida útil. Se hace necesaria la instalación de gas natural, debido a que se tendrá que abastecer a todas las calderas de la central térmica. El diseño del sistema de producción de agua caliente sanitaria garantiza el máximo confort y economía del usuario, compatible con el máximo ahorro energético y la protección del medio ambiente, cubriendo las necesidades de agua caliente sanitaria mediante la combinación de un sistema de calderas a gas con los colectores solares.