Surface characterization techniques for determining the root-mean-square roughness and power spectral densities of optical components

Surface topography and light scattering were measured on 15 samples ranging from those having smooth surfaces to others with ground surfaces. The measurement techniques included an atomic force microscope, mechanical and optical profilers, confocal laser scanning microscope, angle-resolved scattering, and total scattering. The samples included polished and ground fused silica, silicon carbide, sapphire, electroplated gold, and diamond-turned brass. The measurement instruments and techniques had different surface spatial wavelength band limits, so the measured roughnesses were not directly comparable. Two-dimensional power spectral density (PSD) functions were calculated from the digitized measurement data, and we obtained rms roughnesses by integrating areas under the PSD curves between fixed upper and lower band limits. In this way, roughnesses measured with different instruments and techniques could be directly compared. Although smaller differences between measurement techniques remained in the calculated roughnesses, these could be explained mostly by surface topographical features such as isolated particles that affected the instruments in different ways.

Ultraviolet optical and microstructural properties of MgF2 and LaF3 coatings deposited by ion-beam sputtering and boat and electron-beam evaporation

Single layers of MgF2 and LaF3 were deposited upon superpolished fused-silica and CaF2 substrates by ion-beam sputtering (IBS) as well as by boat and electron beam (e-beam) evaporation and were characterized by a variety of complementary analytical techniques. Besides undergoing photometric and ellipsometric inspection, the samples were investigated at 193 and 633 nm by an optical scatter measurement facility. The structural properties were assessed with atomic-force microscopy, x-ray diffraction, TEM techniques that involved conventional thinning methods for the layers. For measurement of mechanical stress in the coatings, special silicon substrates were coated and analyzed. The dispersion behavior of both deposition materials, which was determined on the basis of various independent photometric measurements and data reduction techniques, is in good agreement with that published in the literature and with the bulk properties of the materials. The refractive indices of the MgF2 coatings ranged from 1.415 to 1.440 for the wavelength of the ArF excimer laser (193 nm) and from 1.435 to 1.465 for the wavelength of the F2 excimer laser (157 nm). For single layers of LaF3 the refractive indices extended from 1.67 to 1.70 at 193 nm to ~1.80 at 157 nm. The IBS process achieves the best homogeneity and the lowest surface roughness values (close to 1 nmrms) of the processes compared in the joint experiment. In contrast to MgF2 boat and e-beam evaporated coatings, which exhibit tensile mechanical stress ranging from 300 to 400 MPa, IBS coatings exhibit high compressive stress of as much as 910 MPa. A similar tendency was found for coating stress in LaF3 single layers. Experimental results are discussed with respect to the microstructural and compositional properties as well as to the surface topography of the coatings.

Use of information on the manufacture of samples for the optical characterization of multilayers through a global optimization

We present a procedure for the optical characterization of thin-film stacks from spectrophotometric data. The procedure overcomes the intrinsic limitations arising in the numerical determination of manyparameters from reflectance or transmittance spectra measurements. The key point is to use all theinformation available from the manufacturing process in a single global optimization process. The method is illustrated by a case study of solgel applications.

Correction of aberration in holographic optical tweezers using a Shack-Hartmann sensor

Optical aberration due to the nonflatness of spatial light modulators used in holographic optical tweezers significantly deteriorates the quality of the trap and may easily prevent stable trapping of particles. We use a Shack-Hartmann sensor to measure the distorted wavefront at the modulator plane; the conjugate of this wavefront is then added to the holograms written into the display to counteract its own curvature and thus compensate the optical aberration of the system. For a Holoeye LC-R 2500 reflective device, flatness is improved from 0.8¿ to ¿/16 (¿=532 nm), leading to a diffraction-limited spot at the focal plane of the microscope objective, which makes stable trapping possible. This process could be fully automated in a closed-loop configuration and would eventually allow other sources of aberration in the optical setup to be corrected for.

Adding functionalities to precomputed holograms with random mask multiplexing in holographic optical tweezers

In this study, we present a method designed to generate dynamic holograms in holographic optical tweezers. The approach combines our random mask encoding method with iterative high-efficiency algorithms. This hybrid method can be used to dynamically modify precalculated holograms, giving them new functionalities¿temporarily or permanently¿with a low computational cost. This allows the easy addition or removal of a single trap or the independent control of groups of traps for manipulating a variety of rigid structures in real time.

Magneto-optical Kerr effect in laser-patterned La2/3Sr1/3MnO3 epitaxial thin films

In this study, we have performed magneto-optical Kerr effect (MOKE) measurement on epitaxial La2/3Sr1/3MnO3 thin films containing artificial interfaces created by laser-patterning the SrTiO3 substrate. The observed increase of the resistivity and of the high-field magnetoresistance when measuring the films across the interface arrays are related to the reduction of the magnetization of the interfaces with respect to the rest of the film. As observed by the local MOKE probe, the structural disorder in the manganite film induced by the underlying patterned substrate leads to a large spin disorder responsible for a strong high-field susceptibility of the resistance.

Design of surface forces apparatus for tribology studies combined with nonlinear optical spectroscopy

We describe the design, calibration, and performance of surface forces apparatus with the capability of illumination of the contact interface for spectroscopic investigation using optical techniques. The apparatus can be placed in the path of a Nd-YAG laser for studies of the linear response or the second harmonic and sum-frequency generation from a material confined between the two surfaces. In addition to the standard fringes of equal chromatic order technique, which we have digitized for accurate and fast analysis, the distance of separation can be measured with a fiber-optic interferometer during spectroscopic measurements (2 Å resolution and 10 ms response time). The sample approach is accomplished through application of a motor drive, piezoelectric actuator, or electromagnetic lever deflection for variable degrees of range, sensitivity, and response time. To demonstrate the operation of the instrument, the stepwise expulsion of discrete layers of octamethylcyclotetrasiloxane from the contact is shown. Lateral forces may also be studied by using piezoelectric bimorphs to induce and direct the motion of one surface.

Agglomeration and labour productivity in Spanish industry: a long-term analysis

This paper analyzes the relationship between spatial density of economic activity and interregional differences in the productivity of industrial labour in Spain during the period 1860-1999. In the spirit of Ciccone and Hall (1996) and Ciccone (2002), we analyze the evolution of this relationship over the long term in Spain. Using data on the period 1860-1999 we show the existence of an agglomeration effect linking the density of economic activity with labour productivity in the industry. This effect was present since the beginning of the industrialization process in the middle of the 19th century but has been decreasing over time. The estimated elasticity of labour productivity with respect to employment density was close to 8% in the subperiod 1860-1900, reduces to a value of around 7% in the subperiod 1914-1930, to 4% in the subperiod 1965-1979 and becomes insignificant in the final subperiod 1985-1999. At the end of the period analyzed there is no evidence of the existence of net agglomeration effects in the industry. This result could be explained by an important increase in the congestion effects in large industrial metropolitan areas that would have compensated the centripetal or agglomeration forces at work. Furthermore, this result is also consistent with the evidence of a dispersion of industrial activity in Spain during the last decades.

The geographical concentration of industry across Spanish Regions, 1856-1995

New economic geography models show that there may be a strong relationship between economic integration and the geographical concentration of industries. Nevertheless, this relationship is neither unique nor stable, and may follow a ?-shaped pattern in the long term. The aim of the present paper is to analyze the evolution of the geographical concentration of manufacturing across Spanish regions during the period 1856-1995. We construct several geographical concentration indices for different points in time over these 140 years. The analysis is carried out at two levels of aggregation, in regions corresponding to the NUTS-II and NUTS-III classifications. We confirm that the process of economic integration stimulated the geographical concentration of industrial activity. Nevertheless, the localization coefficients only started to fall after the beginning of the integration of the Spanish Economy into the international markets in the mid-70s, and this new path was not interrupted by Spain¿s entry in the European Union some years later

Metastability and front propagation in the first-order optical Fréedericksz transition

A general dynamical model for the first-order optical Fréedericksz transition incorporating spatial transverse inhomogeneities and hydrodynamic effects is discussed in the framework of a time-dependent Ginzburg-Landau model. The motion of an interface between two coexisting states with different director orientations is considered. A uniformly translating front solution of the dynamical equations for the motion of that interface is described.

The geographical concentration of industry across Spanish Regions, 1856-1995

New economic geography models show that there may be a strong relationship between economic integration and the geographical concentration of industries. Nevertheless, this relationship is neither unique nor stable, and may follow a ?-shaped pattern in the long term. The aim of the present paper is to analyze the evolution of the geographical concentration of manufacturing across Spanish regions during the period 1856-1995. We construct several geographical concentration indices for different points in time over these 140 years. The analysis is carried out at two levels of aggregation, in regions corresponding to the NUTS-II and NUTS-III classifications. We confirm that the process of economic integration stimulated the geographical concentration of industrial activity. Nevertheless, the localization coefficients only started to fall after the beginning of the integration of the Spanish Economy into the international markets in the mid-70s, and this new path was not interrupted by Spain¿s entry in the European Union some years later

Agglomeration and labour productivity in Spanish industry: a long-term analysis

This paper analyzes the relationship between spatial density of economic activity and interregional differences in the productivity of industrial labour in Spain during the period 1860-1999. In the spirit of Ciccone and Hall (1996) and Ciccone (2002), we analyze the evolution of this relationship over the long term in Spain. Using data on the period 1860-1999 we show the existence of an agglomeration effect linking the density of economic activity with labour productivity in the industry. This effect was present since the beginning of the industrialization process in the middle of the 19th century but has been decreasing over time. The estimated elasticity of labour productivity with respect to employment density was close to 8% in the subperiod 1860-1900, reduces to a value of around 7% in the subperiod 1914-1930, to 4% in the subperiod 1965-1979 and becomes insignificant in the final subperiod 1985-1999. At the end of the period analyzed there is no evidence of the existence of net agglomeration effects in the industry. This result could be explained by an important increase in the congestion effects in large industrial metropolitan areas that would have compensated the centripetal or agglomeration forces at work. Furthermore, this result is also consistent with the evidence of a dispersion of industrial activity in Spain during the last decades.

On the industry experience premium and labor mobility

[cat] Hi ha evidència que l'experiència es remunera diferentment segons la indústria. Proposem un model teòric que explica aquestes diferències. Suposem que la mobilitat de treballadors aporta coneixement extern a l'empresa i això augmenta la seva productivitat. Els resultats mostren que l'experiència és millor remunerada en les indústries amb costos de mobilitat baixos, amb molt aprenentatge (learning-by-doing) i alt nivell tecnològic. A més, trobem una relació en forma de U entre la remuneració de l'experiència i el nivell d'absorció de coneixement extern, la substitutibilitat entre diferents tipus de treballadors i la varietat de coneixement dins la indústria. Els resultats són consistents amb l'evidència que les indústries intensives en I and D remuneren millor l'experiència.

Advanced optical microscopies for materials: new trends

This article summarizes the new trends of Optical Microscopy applied to Materials, with examples of applications that illustrate the capabilities of thetechnique.