Blue luminescence at room temperature in defective MgO films

Luminescence spectroscopy has been used to characterize MgO films prepared by rf-sputtering. A clear correlation is found between the appearance of an emission peak centered at approximately 460 nm and the detection of ferromagnetic ordering in the samples. We suggest that cationic vacancies are responsible for the blue-light emission by introducing p states into the electronic band-gap. In accordance with this, our results strongly indicate that cationic vacancies are at the heart of the appearance of long-range magnetic ordering in MgO films.

High-resolution mass spectrometry applied to theidentification of transformation products of quinolones from stability studies and new metabolites of enrofloxacin in chicken muscle tissues

The aim of this work was the identification of new metabolites and transformation products (TPs) in chicken muscle from Enrofloxacin (ENR), Ciprofloxacin (CIP), Difloxacin (DIF) and Sarafloxacin (SAR), which are antibiotics that belong to the fluoroquinolones family. The stability of ENR, CIP, DIF and SAR standard solutions versus pH degradation process (from pH 1.5 to 8.0, simulating the pH since the drug is administered until its excretion) and freeze-thawing (F/T) cycles was tested. In addition, chicken muscle samples from medicated animals with ENR were analyzed in order to identify new metabolites and TPs. The identification of the different metabolites and TPs was accomplished by comparison of mass spectral data from samples and blanks, using liquid chromatography coupled to quadrupole time-of-flight (LC-QqToF) and Multiple Mass Defect Filter (MMDF) technique as a pre-filter to remove most of the background noise and endogenous components. Confirmation and structure elucidation was performed by liquid chromatography coupled to linear ion trap quadrupole Orbitrap (LC-LTQ-Orbitrap), due to its mass accuracy and MS/MS capacity for elemental composition determination. As a result, 21 TPs from ENR, 6 TPs from CIP, 14 TPs from DIF and 12 TPs from SAR were identified due to the pH shock and F/T cycles. On the other hand, 14 metabolites were identified from the medicated chicken muscle samples. Formation of CIP and SAR, from ENR and DIF, respectively, and the formation of desethylene-quinolone were the most remarkable identified compounds.

Combining phospholipases and a liquid lipase for one-step biodiesel production using crude oils

Background Enzymatic biodiesel is becoming an increasingly popular topic in bioenergy literature because of its potential to overcome the problems posed by chemical processes. However, the high cost of the enzymatic process still remains the main drawback for its industrial application, mostly because of the high price of refined oils. Unfortunately, low cost substrates, such as crude soybean oil, often release a product that hardly accomplishes the final required biodiesel specifications and need an additional pretreatment for gums removal. In order to reduce costs and to make the enzymatic process more efficient, we developed an innovative system for enzymatic biodiesel production involving a combination of a lipase and two phospholipases. This allows performing the enzymatic degumming and transesterification in a single step, using crude soybean oil as feedstock, and converting part of the phospholipids into biodiesel. Since the two processes have never been studied together, an accurate analysis of the different reaction components and conditions was carried out. Results Crude soybean oil, used as low cost feedstock, is characterized by a high content of phospholipids (900 ppm of phosphorus). However, after the combined activity of different phospholipases and liquid lipase Callera Trans L, a complete transformation into fatty acid methyl esters (FAMEs >95%) and a good reduction of phosphorus (P <5 ppm) was achieved. The combination of enzymes allowed avoidance of the acid treatment required for gums removal, the consequent caustic neutralization, and the high temperature commonly used in degumming systems, making the overall process more eco-friendly and with higher yield. Once the conditions were established, the process was also tested with different vegetable oils with variable phosphorus contents. Conclusions Use of liquid lipase Callera Trans L in biodiesel production can provide numerous and sustainable benefits. Besides reducing the costs derived from enzyme immobilization, the lipase can be used in combination with other enzymes such as phospholipases for gums removal, thus allowing the use of much cheaper, non-refined oils. The possibility to perform degumming and transesterification in a single tank involves a great efficiency increase in the new era of enzymatic biodiesel production at industrial scale.

Potential of local bio-geoengineering to mitigate dangerous temperature increases in a global warming scenario

Crops and forests are already responding to rising atmospheric carbon dioxide and air temperatures. Increasing atmospheric CO2 concentrations are expected to enhance plant photosynthesis. Nevertheless, after long-term exposure, plants acclimate and show a reduction in photosynthetic activity (i.e. down-regulation). If in the future the Earth"s temperature is allowed to rise further, plant ecosystems and food security will both face significant threats. The scientific community has recognized that an increase in global temperatures should remain below 2°C in order to combat climate change. All this evidence suggests that, in parallel with reductions in CO2 emissions, a more direct approach to mitigate global warming should be considered. We propose here that global warming could be partially mitigated directly through local bio-geoengineering approaches. For example, this could be done through the management of solar radiation at surface level, i.e. by increasing global albedo. Such an effect has been documented in the south-eastern part of Spain, where a significant surface air temperature trend of -0.3°C per decade has been observed due to a dramatic expansion of greenhouse horticulture.

Large gypsum nodules in the Paleogene and Neogene evaporites of Spain: distribution and palaeogeographic significance

Sabkha and deep burial set tings are the most com mon sites where diagenetic anhydrite forms. In a sabkha setting, displacive facies (iso lated nodules, bed ded nodules, enterolithic levels) of early diagenetic or primary anhydrite are generated (Shearman, 1966; Hardie, 1967). These anhydrite facies are commonly foundat the top of shoal ing cycles representing the evolution from subaqueous depositional conditions at the base (carbonates, lutites) to exposure conditions at the top where in ter stitially-grown gypsum/anhydrite de velops ( sabkha cy cles). In a deep burial setting, gypsum transforms to tally to anhydrite with in creas ing temperature and lithostatic pressure (Murray, 1964). Al though this mineral transformation usually preserves the depositional gypsum facies, a significant textural change is in volved in other cases, resulting in replacive anhydrite with a nodular-mosaic or"chicken-wire" fabric (Warren, 2006). In the two settings, how ever, the size of the individual anhydrite nodules is relatively small, rarely reaching some tens of centimetres across. More over, bedding is preserved or little disturbed, al though minor de formation is caused by the displacive sabkha nodules.

The relationship between virtual body ownership and temperature sensitivity.

In the rubber hand illusion tactile stimulation seen on a rubber hand, that is synchronous with tactile stimulation felt on the hidden real hand, can lead to an illusion of ownership over the rubber hand. This illusion has been shown to produce a temperature decrease in the hidden hand, suggesting that such illusory ownership produces disownership of the real hand. Here we apply immersive virtual reality (VR) to experimentally investigate this with respect to sensitivity to temperature change. Forty participants experienced immersion in a VR with a virtual body (VB) seen from a first person perspective. For half the participants the VB was consistent in posture and movement with their own body, and in the other half there was inconsistency. Temperature sensitivity on the palm of the hand was measured before and during the virtual experience. The results show that temperature sensitivity decreased in the consistent compared to the inconsistent condition. Moreover, the change in sensitivity was significantly correlated with the subjective illusion of virtual arm ownership but modulated by the illusion of ownership over the full virtual body. This suggests that a full body ownership illusion results in a unification of the virtual and real bodies into one overall entity - with proprioception and tactile sensations on the real body integrated with the visual presence of the virtual body. The results are interpreted in the framework of a"body matrix" recently introduced into the literature.

Temperature dependence of the magnetization processes in Co/Al oxide/Permalloy trilayers

The magnetization process of Co/Al oxide/Py trilayers and its evolution with the temperature have been analyzed. The particular behavior of the Co layers, including the shift of the hysteresis loops and a coercivity increase with the decrease of temperature, is related with the apparition of a CoO layer at the Co/Al-oxide interface.

Systematic study of the temperature dependence of the saturation magnetization in Fe, Fe-Ni and Co-based amorphous alloys

Magnetization versus temperature in the temperature interval 2-200 K was measured for amorphous alloys of three different compositions: Fe 81.5B14.5Si4, Fe40Ni38 Mo4B18, and Co70Fe5Ni 2Mo3B5Si15. The measurements were performed by means of a SQUID (superconducting quantum interference device) magnetometer. The aim was to extract information about the different mechanisms contributing to thermal demagnetization. A powerful data analysis technique based on successive minimization procedures has demonstrated that Stoner excitations of the strong ferromagnetic type play a significant role in the Fe-Ni alloy studied. The Fe-rich and Co-rich alloys do not show a measurable contribution from single-particle excitations.

Pyroelectric conversion: harvesting energy from temperature fluctuations

Peer reviewed

Quasi real-time Raman studies on the growth of Cu-In-S thin films

In this work annealing and growth of CuInS2 thin films is investigated with quasireal-time in situ Raman spectroscopy. During the annealing a shift of the Raman A1 mode towards lower wave numbers with increasing temperature is observed. A linear temperature dependence of the phonon branch of ¿2 cm¿1/100 K is evaluated. The investigation of the growth process (sulfurization of metallic precursors) with high surface sensitivity reveals the occurrence of phases which are not detected with bulk sensitive methods. This allows a detailed insight in the formation of the CuInS2 phases. Independent from stoichiometry and doping of the starting precursors the CuAu ordering of CuInS2 initially forms as the dominating ordering. The transformation of the CuAu ordering into the chalcopyrite one is, in contrast, strongly dependent on the precursor composition and requires high temperatures.

Study of post-deposition contamination in low-temperature deposited polysilicon films

The presence of hydrogen in polysilicon films obtained at low temperatures by hot-wire CVD and the post-deposition oxidation by air-exposure of the films are studied in this paper. The experimental results from several characterization techniques (infrared spectroscopy, X-ray photoelectron spectroscopy, secondary ion mass spectrometry and wavelength dispersive spectroscopy) showed that hydrogen and oxygen are homogeneously distributed at grain boundaries throughout the depth of the films. Hydrogen is introduced during the growth process and its concentration is higher in samples deposited at lower temperatures. Oxygen diffuses along the grain boundaries and binds to silicon atoms, mainly in Si 2O groups.

In vitro evaluation of the temperature increment at the external root surface after Er,Cr: YSGG laser irradiation of the root canal

Objectives: A study was made to determine the temperature increment at the dental root surface following Er,Cr:YSGG laser irradiation of the root canal. Design. Human canines and incisors previously instrumented to K file number ISO 30 were used. Irradiation was carried out with glass fiber endodontic tips measuring 200 μm in diameter and especially designed for insertion in the root canal. The teeth were irradiated at 1 and 2 W for 30 seconds, without water spraying or air, and applying a continuous circular movement (approximately 2 mm/sec.) in the apico-coronal direction. Results: At the 1 W power setting, the mean temperature increment was 3.84ºC versus 5.01ºC at 2 W. In all cases the difference in mean value obtained after irradiation versus the mean baseline temperature proved statistically significant (p< 0.05). Conclusions: Application of the Er,Cr:YSGG laser gives rise to a statistically significant temperature increment at the external root surface, though this increment is probably clinically irrelevant, since it would appear to damage the tissues (periodontal ligament and alveolar bone) in proximity to the treated tooth

Effect of temperature and moisture on the dormancy and activation pattern of Oxalis latifolia bulbs

Con objeto de buscar información para un mejor control de Oxalis latifolia Kunth, se ha estudiado el efecto que presentan la temperatura y la humedad sobre la activación de sus bulbos, tanto en la forma común como en la forma Cornwall de la misma. Los bulbos de la mala hierba se mantuvieron en un refrigerador a +4°C durante 13, 20, 27, 41, 48 y 55 días. Se sacaron tres grupos de 30 bulbos de cada forma en cada fecha de muestreo y se colocaron a 21°C; 15 de ellos se mantuvieron en condiciones de sequía —no se regaron— y otros 15 en condiciones de humedad —añadiendo el agua necesaria—. Los resultados muestran que la activación ocurre durante un período prolongado de tiempo en ambas formas, tanto en seco como en húmedo. También se observó que los bulbos secos se activaron antes que los húmedos y los de la forma común antes que los Cornwall. Se observaron dos patrones de activación: los bulbos secos de la forma común generalmente presentaron una activación que sigue un patrón logarítmico, mientras que sus bulbos humedecidos mostraron una tendencia linear; los bulbos Cornwall se activaron con una tendencia exponencial en la mayoría de los casos. El tiempo medio requerido para la activación después del almacenamiento en frío fue constante en la forma común, sin embargo la activación de Cornwall fue más rápida cuanto más tiempo permanecieron almacenados en frío.

Earliness per se and its dependence upon temperature in diploid wheat lines differing in the major gene Eps-Am1 alleles

Differences in development among wheat cultivars are not only restricted to photoperiod and vernalization responses. When both requirements are fully satisfied differences may still arise due to earliness per se. It is not clear at present to what extent this trait is ‘ intrinsically ’ expressed (a constitutive trait) independently of the environmental conditions so that it might be selected under any thermal condition or if it may be altered to the extent of showing a crossover interaction with temperature in which the ranking of wheat genotypes may be altered. The present study assessed the influence of temperature on the intrinsic earliness for lines of diploid wheat characterized for their differences in a major gene for intrinsic earliness, but also possibly differing in their genetic background for other factors controlling this polygenic trait. To do so the lines were grown individually in two temperature regimes (16 and 23 xC) under long days having previously been fully vernalized. Multiple comparisons analyses were carried out among lines of the same allelic group for the Eps-Am1 gene. Results indicated that within each group there were lines that did not differ in their earliness per se, others differed but without exhibiting any linertemperature interaction and finally different types of interaction were shown, including cases where the ranking of lines was altered depending on the growing temperature. It is thus possible that the selection of a genotype based on its earliness per se in an environment might not represent the same performance in another location where temperature varied significantly.

Effect of temperature and carpel size during pre-anthesis on potential grain weight in wheat

The effect of environmental conditions immediately before anthesis on potential grain weight was investigated in wheat at the experimental field of the Faculty of Agronomy (University of Buenos Aires, Argentina) during 1995 and 1996. Plants of two cultivars of wheat were grown in two environments (two contrasting sowing dates) to provide different background temperature conditions. In these environments, transparent boxes were installed covering the spikes in order to increase spike temperature for a short period (c. 6 days) immediately before anthesis, i.e. between ear emergence and anthesis. In both environments, transparent boxes increased mean temperatures by at least 3n8 mC. These increases were almost entirely due to the changes in maximum temperatures because minimum temperatures were little affected. Final grain weight was significantly reduced by higher temperature during the ear emergence–anthesis period. It is possible that this reduction could be mediated by the effect of the heat treatment on carpel weight at anthesis because a curvilinear association between final grain weight and carpel weight at anthesis was found. This curvilinear association may also indicate a threshold carpel weight for maximizing grain weight.