Environmental Structural Decomposition Analysis of Italian Emissions, 1995-2005

[spa] El estudio analiza la evolución de los gases de efecto invernadero (GEI) y las emisiones de acidificación para Italia durante el periodo 1995-2005. Los datos muestran que mientras las emisiones que contribuyen a la acidificación han disminuido constantemente, las emisiones de GEI han aumentado debido al aumento de dióxido de carbono. El objetivo de este estudio es poner de relieve cómo diferentes factores económicos, en particular el crecimiento económico, el desarrollo de una tecnología menos contaminante y la estructura del consumo, han impulsado la evolución de las emisiones. La metodología propuesta es un análisis de descomposición estructural (ADE), método que permite descomponer los cambios de la variable de interés entre las diferentes fuerzas y revelar la importancia de cada factor. Por otra parte, este estudio considera la importancia del comercio internacional e intenta incluir el “problema de la responsabilidad”. Es decir, a través de las relaciones comerciales internacionales, un país podría estar exportando procesos de producción contaminantes sin una reducción real de la contaminación implícita en su patrón de consumo. Con este fin, siguiendo primero un enfoque basado en la “responsabilidad del productor”, el ADE se aplica a las emisiones causadas por la producción nacional. Sucesivamente, el análisis se mueve hacia un enfoque basado en la “responsabilidad del consumidor" y la descomposición se aplica a las emisiones relacionadas con la producción nacional o la producción extranjera que satisface la demanda interna. De esta manera, el ejercicio permite una primera comprobación de la importancia del comercio internacional y pone de relieve algunos resultados a nivel global y a nivel sectorial.

Influence of the feeding mechanism on deposits of square particles

In a previous paper [Hidalgo et al., Phys. Rev. Lett. 103, 118001 (2009)] it was shown that square particles deposited in a silo tend to align with a diagonal parallel to the gravity, giving rise to a deposit with very particular properties. Here we explore, both experimentally and numerically, the effect on these properties of the filling mechanism. In particular, we modify the volume fraction of the initial configuration from which the grains are deposited. Starting from a very dilute case, increasing the volume fraction results in an enhancement of the disorder in the final deposit characterized by a decrease of the final packing fraction and a reduction of the number of particles oriented with their diagonal in the direction of gravity. However, for very high initial volume fractions, the final packing fraction increases again. This result implies that two deposits with the same final packing fraction can be obtained from very different initial conditions. The structural properties of such deposits are analyzed, revealing that, although the final volume fraction is the same, their micromechanical properties notably differ.

Environmental Structural Decomposition Analysis of Italian Emissions, 1995-2005

[spa] El estudio analiza la evolución de los gases de efecto invernadero (GEI) y las emisiones de acidificación para Italia durante el periodo 1995-2005. Los datos muestran que mientras las emisiones que contribuyen a la acidificación han disminuido constantemente, las emisiones de GEI han aumentado debido al aumento de dióxido de carbono. El objetivo de este estudio es poner de relieve cómo diferentes factores económicos, en particular el crecimiento económico, el desarrollo de una tecnología menos contaminante y la estructura del consumo, han impulsado la evolución de las emisiones. La metodología propuesta es un análisis de descomposición estructural (ADE), método que permite descomponer los cambios de la variable de interés entre las diferentes fuerzas y revelar la importancia de cada factor. Por otra parte, este estudio considera la importancia del comercio internacional e intenta incluir el “problema de la responsabilidad”. Es decir, a través de las relaciones comerciales internacionales, un país podría estar exportando procesos de producción contaminantes sin una reducción real de la contaminación implícita en su patrón de consumo. Con este fin, siguiendo primero un enfoque basado en la “responsabilidad del productor”, el ADE se aplica a las emisiones causadas por la producción nacional. Sucesivamente, el análisis se mueve hacia un enfoque basado en la “responsabilidad del consumidor" y la descomposición se aplica a las emisiones relacionadas con la producción nacional o la producción extranjera que satisface la demanda interna. De esta manera, el ejercicio permite una primera comprobación de la importancia del comercio internacional y pone de relieve algunos resultados a nivel global y a nivel sectorial.

Influencia de la tectónica en la sedimentación continental de la cuenca del Vallés-Penedés (Prov.Barcelona, España) durante el Mioceno inferior.

A very important alluvial fan clastic sedimentation, took place in the NNESSW trending Valles-Penedes graben (northeastem Spain) during Miocene time. Shallow lacustrine and paludine areas developed in distal zones of these alluvial fan complexes during Burdigalian (Early Miocene). At that time both facies development and their distribution were closely controlled by tectonic activity. Fault scarp retreat and back-faulting processes in the southeastem edge of the basin (observed in westem Valles afea), originated an expansive advance of distal alluvial-fan facies in that direction. The decreasing or cessation of the activity of the southeastern margin fault ca~sedi,n Late Burdigalian time (while faults in the northwestern margin were still active) facies redistribution, and gave way to the assymetry of the basin. Finally lacustrine, marine and transitional deposits of late burdigalian and langhian age, were laid down overlapping the southeastem inactive margins.

On the multiwavelength spectrum of the microquasar 1E1740.7-2942

The microquasar 1E 1740.7-2942 is a source located in the direction of the Galactic Center. It has been detected at X-rays, soft gamma-rays, and in the radio band, showing an extended radio component in the form of a double-sided jet. Although no optical counterpart has been found so far for 1E 1740.7-2942, its X-ray activity strongly points to a galactic nature. Aims.We aim to improve our understanding of the hard X-ray and gamma-ray production in the system, exploring whether the jet can emit significantly at high energies under the light of the present knowledge. Methods.We have modeled the source emission, from radio to gamma-rays, with a cold-matter dominated jet model. INTEGRAL data combined with radio and RXTE data, as well as EGRET and HESS upper-limits, are used to compare the computed and the observed spectra. Results.From our modeling, we find out that jet emission cannot explain the high fluxes observed at hard X-rays without violating at the same time the constraints from the radio data, favoring the corona origin of the hard X-rays. Also, 1E 1740.7-2942 might be detected by GLAST or AGILE at GeV energies, and by HESS and HESS-II beyond 100 GeV, with the spectral shape likely affected by photon-photon absorption in the disk and corona photon fields.

Effect of dripline flushing on subsurface drip irrigation systems

The velocity of dripline flushing in subsurface drip irrigation (SDI) systems affects system design, cost, management, performance, and longevity. A 30‐day field study was conducted at Kansas State University to analyze the effect of four targeted flushing velocities (0.23, 0.30, 0.46, and 0.61 m/s) for a fixed 15 min duration of flushing and three flushing frequencies (no flushing or flushing every 15 or 30 days) on SDI emitter discharge and sediments within the dripline and removed in the flushing water. At the end of the field experiment (371 h), the amount of solids carried away by the flushing water and retained in every lateral were determined as well as laboratory determination of emitter discharge for every single emitter within each dripline. Greater dripline flushing velocities, which also resulted in greater flushing volumes, tended to result in greater amounts of solids in the flushing water, but the differences were not always statistically significant. Neither the frequency of flushing nor the interaction of flushing frequency and velocity significantly affected the amount of solids in the flushing water. There was a greater concentration of solids in the beginning one‐third of the 90 m laterals, particularly for treatments with no flushing or with slower dripline flushing velocities. As flushing velocity and concurrently flushing volume increased, there was a tendency for greater solids removal and/or more equal distribution within the dripline. At the end of the field study, the average emitter discharge as measured in the laboratory for a total of 3970 emitters was 0.64 L/h. which was significantly less (approximately 2.5%) than the discharge for new and unused emitters. Only six emitters were nearly or fully clogged, with discharges between 0% and 5% of new and unused emitters. Flushing velocity and flushing frequency did not have consistent significant effects on emitter discharge, and those numerical differences that did exist were small (<3%). Emitter discharge was approximately 3% less for the distal ends of the driplines (last 20% of the dripline). Although not a specific factor in the study, the results of solids removals during flushing and solids retention within the different dripline sections suggest that duration of flushing may be a more cost‐effective management option than increasing the dripline flushing velocity through SDI system design. Finally, although microirrigation system components have been improved over the years, the need for flushing to remove solids and reduce clogging potential has not been eliminated

Learning journalistic opinion genres using CLIL methodology

The Faculty of Business and Communication recently started an internationalization process that, in two year’s time, will allow all undergraduate students (studying Journalism, Audiovisual Communication, Advertising and Public Relations, Business and Marketing) to take 25% of their subjects in English using CLIL methodology. Currently, Journalism is the degree course with the greatest percentage of CLIL subjects, for example Current Affairs Workshop, a subject dedicated to analyzing current news using opinion genres. Moreover, because of the lack of other subjects offered in English, ERASMUS students have to take some journalism subjects in order to complete their international passport, and one of the classes they choose is the Current Affairs Workshop. The aim of this paper is to explore how CLIL methodology can be useful for learning journalistic opinion genres (chat-shows, discussions and debates) in a subject where Catalan Communication students –with different levels of English- share their knowledge with European students of other social disciplines. Students work in multidisciplinary groups in which they develop real radio and TV programs, adopting all the roles (moderator, technician, producer and participants), analyzing daily newspapers and other sources to create content, based on current affairs. This paper is based on the participant observation of the lecturers of the subject, who have designed different activities related to journalistic genres, where students can develop their skills according to the role they play in every assignment. Examples of successful lessons will be given, in addition to the results of the course: both positive and negative. Although the objective of the course is to examine professional routines related to opinion genres, and students are not directly graded on their level of English, the Catalan students come to appreciate how they finally overcome their fear of working in a foreign language. This is a basic result of their experience.

Comparing assays for the measurement of AhR ligand activity

In this thesis (TFG) the results of the comparison of three assays for the measurement of AhR ligand activity are exposed. This study was part of a collaborative project aiming at the characterization of the AhR signaling activities of known naturally occurring compounds to explore the potential of using non-toxic compounds to treat inflammatory diseases via oral administration. The first goal of this project was to find an assay able to measure AhR-activity, so the comparison of different assays has been done in order to find the most convenient one according to the efficiency, sensitivity and precision. Moreover, other elements with operational nature such as price, toxicity of components or ease of use has been considered. From the use of compounds known from the literature to be AhR ligands, three assays have been tested: (1) P450-GloTM CYP1A2 Induction/Inhibition assay, (2) quantitative Polymerase Chain Reaction (qPCR) and (3) DR. CALUX® Bioassay. Moreover, a different experiment using the last assay was performed for the study in vivo of the transport of the compounds tested. The results of the TFG suggested the DR. CALUX® Bioassay as the most promising assay to be used for the screening of samples as AhR-ligands because it is quicker, easier to handle and less expensive than qPCR and more reproducible than the CYP1A2 Induction/Inhibition assay. Moreover, the use of this assay allowed having a first idea of which compounds are uptaken by the epithelial barrier and in with direction the transport happens.

Contenidos educativos en abierto

Peer-reviewed

Automatització d'un procés de fabricació de peces plàstiques

RESUM L'automatització s'utilitza des de fa molts anys, tot i que va començar a agafar la definició que coneixem actualment al voltant dels anys seixanta i setanta, moment en què es comencen a comercialitzar els primers PLC. A partir d'aquí, el seu creixement ha estat exponencial. En aquest sentit, la tecnologia ha anat avançant i ha augmentat els components que la forma, per això a hores d'ara encara no sabem fins on podrà arribar i què aconseguirà. Per a la indústria tot això ha significat l'automatització de processos que fins ara utilitzaven molt mà d'obra, reduint-la dràsticament. Una de les indústries que més s'ha beneficiat de tots aquests avenços ha estat la de l'automoció, concretament les seves grans línies de producció, automatitzades a uns nivells que fins fa poc temps eren impensables. Aquest projecte forma part d'aquesta indústria, no directament per a la construcció de l'automòbil, sinó indirectament, ja que l'empresa per a la qual s'ha fet l'automatització fabrica peces plàstiques per a automòbils. Concretament, unes peces amb uns injerts metàl•lics conductors que es munten a tots els vehicles i s'utilitzen per accionar els neteja vidres dels cotxes. Aquest fet implica que la fabricació i el disseny de la peça sigui curosament vigilat i controlat per al client final, amb uns controls de qualitat extremadament exigents. El funcionament del procés de fabricació es fa a partir d'unes peces de plàstic produïdes per una injectora que es fan passar per unes estacions automatitzades, cada una de les quals fa una acció concreta per aconseguir el muntatge final.

Control d'il·luminació i ventilació d'un pàrquing

El treball presentat ve motivat per la necessitat d’instal•lació d’un pàrquing públic i privat de nova construcció a nivell d’il•luminació i ventilació. Per poder satisfer les necessitats del nostre client d’estalvi energètic i confort en l’edifici es decideix d’implementar una instal•lació immòtica que és l’aplicació de tècniques de gestió i control automatitzat a un edifici terciari amb bus de comunicació KNX/EIB. Per a la il•luminació s’han utilitzat fluorescents amb balasts DALI, que permeten la seva regulació i control, per així poder adequar en tot moment l’encesa i intensitat de llum d’aquests. En quant a la ventilació s’han utilitzat variadors de freqüència per també poder optimitzar el funcionament dels ventiladors podent posar-los en marxa quan realment sigui necessari i a la potència que calgui. Per enllaçar tots els elements de la instal•lació, detectors i actuadors, sorgeig la necessitat d’implementar xarxes de comunicació com el KNX/EIB, DALI, Modbus i Ethernet. Per gestionar variables, comunicacions i controlar elements, s´hi han implementen dos autòmats programables a més d’un PC integrat per la visualització i el control del pàrquing. S’ha aconseguit de realitzar un pàrquing totalment automàtic on no és necessaria l’actuació dels operaris i amb les principals càrregues elèctriques totalment regulables en potència. S’ha comprovat que la instal•lació funciona per sota de la potència nominal de les càrregues amb l’estalvi energètic que això suposa.