The regional distribution of unemployment. What do micro-data tell us?

Regional disparities in unemployment rates are large and persistent. The literature provides evidence of their magnitude and evolution, as well as evidence of the role of certain economic, demographic and environmental factors in explaining the gap between regions of low and high unemployment. Most of these studies, however, adopt an aggregate approach and so do not account for the individual characteristics of the unemployed and employed in each region. This paper, by drawing on micro-data from the Spanish wave of the Labour Force Survey, seeks to remedy this shortcoming by analysing regional differentials in unemployment rates. An appropriate decomposition of the regional gap in the average probability of being unemployed enables us to distinguish between the contribution of differences in the regional distribution of individual characteristics from that attributable to a different impact of these characteristics on the probability of unemployment. Our results suggest that the well-documented disparities in regional unemployment are not just the result of regional heterogeneity in the distribution of individual characteristics. Non-negligible differences in the probability of unemployment remain after controlling for this type of heterogeneity, as a result of differences across regions in the impact of the observed characteristics. Among the factors considered in our analysis, regional differences in the endowment and impact of an individual’s education are shown to play a major role.

Tectonic-palaeoenvironmental forcing of clay-mineral assemblages in nonmarine settings: the Oligocene-Miocene As Pontes Basin (Spain)

Two small, alluvial-lacustrine subbasins developed during the early restraining overstep stages of the Oligocene-Miocene As Pontes strike-slip Basin (NW Spain). Later, the basin evolved into a restraining bend stage and an alluvial-swamp-dominated depositional framework developed. The palaeobiological record demonstrates that the Oligocene-Miocene palaeoclimate in NW Spain was subtropical, warm and humid to subhumid.

Innovative milieu, micro firms and local development in Barcelona

Peer-reviewed

El software libre al servicio de la economía productiva : Caso real de implantación de un ERP en una micro PYME

Este trabajo de fin de grado intenta, mediante el caso real de la implantación de un ERP en una micro PYME, ajustar a la realidad socioeconómica de la gran mayoría de empresas españolas las técnicas de implantación de software y de gestión de proyectos, usando como elemento conductor un ERP de software libre, para conseguir el triple objetivo de mantener los ratios de calidad deseados en cualquier proyecto de ingeniería de software, con unos costes asumibles por una micro PYME y satisfaciendo las necesidades de negocio.

Anisotropic surface properties of micro/nanostructured a-C:H:F thin films with self-assembly applications

The singular properties of hydrogenated amorphous carbon (a-C:H) thin filmsdeposited by pulsed DC plasma enhanced chemical vapor deposition (PECVD), such as hardness and wear resistance, make it suitable as protective coating with low surface energy for self-assembly applications. In this paper, we designed fluorine-containing a-C:H (a-C:H:F) nanostructured surfaces and we characterized them for self-assembly applications. Sub-micron patterns were generated on silicon through laser lithography while contact angle measurements, nanotribometer, atomic force microscopy (AFM), and scanning electron microscopy (SEM) were used to characterize the surface. a-C:H:F properties on lithographied surfaces such as hydrophobicity and friction were improved with the proper relative quantity of CH4 and CHF3 during deposition, resulting in ultrahydrophobic samples and low friction coefficients. Furthermore, these properties were enhanced along the direction of the lithographypatterns (in-plane anisotropy). Finally, self-assembly properties were tested with silicananoparticles, which were successfully assembled in linear arrays following the generated patterns. Among the main applications, these surfaces could be suitable as particle filter selector and cell colony substrate.

Private micro-irrigation costs using reclaimed water

The cost of reusing water in micro-irrigation at the field level has not been studied in depth although the use of effluents in agriculture is a viable alternative in areas where water is scarce or there is intense competition for its use. The aim of the present study is to analyse the private costs of water reuse in micro-irrigation in an experimental plot. This analysis is intended to provide information about the decision a farmer would make when the choice to use conventional or reclaimed water is guided by cost criteria. The components of the total costs of different combinations of four types of filters and five emitters that can be installed in micro-irrigation systems using reclaimed water have been studied with the data obtained from an experimental plot in conditions similar to those of fruit orchards. Different scenarios that compared the costs of using conventional or reclaimed water in terms of water price and nutrient content were also studied. The results show that a proper combination of filters and emitters can save up to 33% in irrigation costs. Capital costs and maintenance costs were the most variable among the different combinations. Scenario analysis showed that the greater price of reclaimed water could be compensated by high nutrient contents, which would reduce fertilizer costs

Micro- and nanostructuring of poly(ethylene-2,6-naphthalate) surfaces, for biomedical applications, using polymer replication techniques

Here we investigate the formation of superficial micro- and nanostructures in poly(ethylene-2,6-naphthalate) (PEN), with a view to their use in biomedical device applications, and compare its performance with a polymer commonly used for the fabrication of these devices, poly(methyl methacrylate) (PMMA). The PEN is found to replicate both micro- and nanostructures in its surface, albeit requiring more forceful replication conditions than PMMA, producing a slight increase in surface hydrophilicity. This ability to form micro/nanostructures, allied to biocompatibility and good optical transparency, suggests that PEN could be a useful material for production of, or for incorporation into, transparent devices for biomedical applications. Such devices will be able to be autoclaved, due to the polymer's high temperature stability, and will be useful for applications where forceful experimental conditions are required, due to a superior chemical resistance over PMMA.