Roughness and light scattering of ion-beam-sputtered fluoride coatings for 193 nm

Scattering characteristics of multilayer fluoride coatings for 193 nm deposited by ion beam sputtering and the related interfacial roughnesses are investigated. Quarter- and half-wave stacks of MgF2 and LaF3 with increasing thickness are deposited onto CaF2 and fused silica and are systematically characterized. Roughness measurements carried out by atomic force microscopy reveal the evolution of the power spectral densities of the interfaces with coating thickness. Backward-scattering measurements are presented, and the results are compared with theoretical predictions that use different models for the statistical correlation of interfacial roughnesses.

Correction of aberration in holographic optical tweezers using a Shack-Hartmann sensor

Optical aberration due to the nonflatness of spatial light modulators used in holographic optical tweezers significantly deteriorates the quality of the trap and may easily prevent stable trapping of particles. We use a Shack-Hartmann sensor to measure the distorted wavefront at the modulator plane; the conjugate of this wavefront is then added to the holograms written into the display to counteract its own curvature and thus compensate the optical aberration of the system. For a Holoeye LC-R 2500 reflective device, flatness is improved from 0.8¿ to ¿/16 (¿=532 nm), leading to a diffraction-limited spot at the focal plane of the microscope objective, which makes stable trapping possible. This process could be fully automated in a closed-loop configuration and would eventually allow other sources of aberration in the optical setup to be corrected for.

New constraints on a light spinless particle coupled to photons

We obtain new stringent constraints on a light spinless particle f coupled only to photons at low energies, considering its effects on the extragalactic photon background, the black-body spectrum of the cosmic microwave background radiation and the cosmological abundance of deuterium.

Light scattering from suspensions under external gradients

We analyze the light-scattering spectrum of a suspension in a viscoelastic fluid under density and velocity gradients. When a density gradient is present, the dynamic structure factor exhibits universality in the sense that its expression depends only on the reduced frequency and the reduced density gradient. For a velocity gradient, however, the universality breaks down. In this last case we have found a transition point from one to three characteristic frequencies in the spectrum, which is governed by the value of the external gradient. The presence of the viscoelastic time scales introduces a shift in the ``critical¿¿ point.

Were Spanish migrants attracted by industrial agglomerations?: an analysis for the interwar years in the light of the new economic geography

In this paper we examine whether access to markets had a significant influence onmigration choices of Spanish internal migrants in the inter-war years. We perform astructural contrast of a New Economic Geography model that focus on the forwardlinkage that links workers location choice with the geography of industrial production,one of the centripetal forces that drive agglomeration in the NEG models. The resultshighlight the presence of this forward linkage in the Spanish economy of the inter-warperiod. That is, we prove the existence of a direct relation between workers¿ localizationdecisions and the market potential of the host regions. In addition, the direct estimationof the values associated with key parameters in the NEG model allows us to simulatethe migratory flows derived from different scenarios of the relative size of regions andthe distances between them. We show that in Spain the power of attraction of theagglomerations grew as they increased in size, but the high elasticity estimated for themigration costs reduced the intensity of the migratory flows. This could help to explainthe apparently low intensity of internal migrations in Spain until its upsurge during the1920s. This also explains the geography of migrations in Spain during this period,which hardly affected the regions furthest from the large industrial agglomerations (i.e.,regions such as Andalusia, Estremadura and Castile-La Mancha) but had an intenseeffect on the provinces nearest to the principal centres of industrial development.

Were Spanish migrants attracted by industrial agglomerations?: an analysis for the interwar years in the light of the new economic geography

In this paper we examine whether access to markets had a significant influence onmigration choices of Spanish internal migrants in the inter-war years. We perform astructural contrast of a New Economic Geography model that focus on the forwardlinkage that links workers location choice with the geography of industrial production,one of the centripetal forces that drive agglomeration in the NEG models. The resultshighlight the presence of this forward linkage in the Spanish economy of the inter-warperiod. That is, we prove the existence of a direct relation between workers¿ localizationdecisions and the market potential of the host regions. In addition, the direct estimationof the values associated with key parameters in the NEG model allows us to simulatethe migratory flows derived from different scenarios of the relative size of regions andthe distances between them. We show that in Spain the power of attraction of theagglomerations grew as they increased in size, but the high elasticity estimated for themigration costs reduced the intensity of the migratory flows. This could help to explainthe apparently low intensity of internal migrations in Spain until its upsurge during the1920s. This also explains the geography of migrations in Spain during this period,which hardly affected the regions furthest from the large industrial agglomerations (i.e.,regions such as Andalusia, Estremadura and Castile-La Mancha) but had an intenseeffect on the provinces nearest to the principal centres of industrial development.

Bond strength of orthodontic brackets using different light and self-curing cements

The purpose of the study was to evaluate the shear bond strength of stainless steel orthodontic brackets directly bonded to extracted human premolar teeth. Fifty teeth were randomly divided into ¿ve groups: (1) System One (chemically cured composite resin), (2) Light Bond (light-cured composite resin), (3) Vivaglass Cem (self-curing glass ionomer cement), (4) Fuji Ortho LC (light-cured glass ionomer cement) used after 37% orthophosphoric acid¿etching of enamel (5) Fuji Ortho LC without orthophosphoric acid¿etching. The brackets were placed on the buccal and lingual surfaces of each tooth, and the specimens were stored in distilled water (24 hours) at 378C and thermocycled. Teeth were mounted on acrylic block frames, and brackets were debonded using an Instron machine. Shear bond strength values at fracture (Nw)were recorded. ANOVA and Student-Newman-Keuls multiple comparison tests were performed (P , .05). Bonding failure site was recorded by stereomicroscope and analyzed by Chi-square test, selected specimens of each group were observed by scanning electron microscope. System One attained the highest bond strength. Light Bond and Fuji Ortho LC, when using an acid-etching technique, obtained bond strengths that were within the range of estimated bond strength values for successful clinical bonding. Fuji Ortho LC and Vivaglass Cem left an almost clean enamel surface after debracketing.

Dissociation from BiP and Retrotranslocation of Unassembled Immunoglobulin Light Chains Are Tightly Coupled to Proteasome Activity

Unassembled immunoglobulin light chains expressed by the mouse plasmacytoma cell line NS1 (KNS1) are degraded in vivo with a half-life of 50-60 min in a way that closely resembles endoplasmic reticulum (ER)-associated degradation (Knittler et al., 1995). Here we show that the peptide aldehydes MG132 and PS1 and the specific proteasome inhibitor lactacystin effectively increased the half-life of KNS1, arguing for a proteasome-mediated degradation pathway. Subcellular fractionation and protease protection assays have indicated an ER localization of KNS1 upon proteasome inhibition. This was independently confirmed by the analysis of the folding state of KNS1and size fractionation experiments showing that the immunoglobulin light chain remained bound to the ER chaperone BiP when the activity of the proteasome was blocked. Moreover, kinetic studies performed in lactacystin-treated cells revealed a time-dependent increase in the physical stability of the BiP-KNS1complex, suggesting that additional proteins are present in the older complex. Together, our data support a model for ER-associated degradation in which both the release of a soluble nonglycosylated protein from BiP and its retrotranslocation out of the ER are tightly coupled with proteasome activity.

Advanced light microscopy techniques

This article summarizes the basic principles of light microscopy, with examples of applications in biomedicine that illustrate the capabilities of thetechnique.

Score light

Award-winning

Optimized back-focal-plane interferometry directly measures forces of optically trapped particles

Back-focal-plane interferometry is used to measure displacements of optically trapped samples with very high spatial and temporal resolution. However, the technique is closely related to a method that measures the rate of change in light momentum. It has long been known that displacements of the interference pattern at the back focal plane may be used to track the optical force directly, provided that a considerable fraction of the light is effectively monitored. Nonetheless, the practical application of this idea has been limited to counter-propagating, low-aperture beams where the accurate momentum measurements are possible. Here, we experimentally show that the connection can be extended to single-beam optical traps. In particular, we show that, in a gradient trap, the calibration product κ·β (where κ is the trap stiffness and 1/β is the position sensitivity) corresponds to the factor that converts detector signals into momentum changes; this factor is uniquely determined by three construction features of the detection instrument and does not depend, therefore, on the specific conditions of the experiment. Then, we find that force measurements obtained from back-focal-plane displacements are in practice not restricted to a linear relationship with position and hence they can be extended outside that regime. Finally, and more importantly, we show that these properties are still recognizable even when the system is not fully optimized for light collection. These results should enable a more general use of back-focal-plane interferometry whenever the ultimate goal is the measurement of the forces exerted by an optical trap.

Optimized back-focal-plane interferometry directly measures forces of optically trapped particles

Back-focal-plane interferometry is used to measure displacements of optically trapped samples with very high spatial and temporal resolution. However, the technique is closely related to a method that measures the rate of change in light momentum. It has long been known that displacements of the interference pattern at the back focal plane may be used to track the optical force directly, provided that a considerable fraction of the light is effectively monitored. Nonetheless, the practical application of this idea has been limited to counter-propagating, low-aperture beams where the accurate momentum measurements are possible. Here, we experimentally show that the connection can be extended to single-beam optical traps. In particular, we show that, in a gradient trap, the calibration product κ·β (where κ is the trap stiffness and 1/β is the position sensitivity) corresponds to the factor that converts detector signals into momentum changes; this factor is uniquely determined by three construction features of the detection instrument and does not depend, therefore, on the specific conditions of the experiment. Then, we find that force measurements obtained from back-focal-plane displacements are in practice not restricted to a linear relationship with position and hence they can be extended outside that regime. Finally, and more importantly, we show that these properties are still recognizable even when the system is not fully optimized for light collection. These results should enable a more general use of back-focal-plane interferometry whenever the ultimate goal is the measurement of the forces exerted by an optical trap.

Positional stability of holographic optical traps

The potential of digital holography for complex manipulation of micron-sized particles with optical tweezers has been clearly demonstrated. By contrast, its use in quantitative experiments has been rather limited, partly due to fluctuations introduced by the spatial light modulator (SLM) that displays the kinoforms. This is an important issue when high temporal or spatial stability is a concern. We have investigated the performance of both an analog-addressed and a digitally-addressed SLM, measuring the phase fluctuations of the modulated beam and evaluating the resulting positional stability of a holographic trap. We show that, despite imparting a more unstable modulation to the wavefront, our digitally-addressed SLM generates optical traps in the sample plane stable enough for most applications. We further show that traps produced by the analog-addressed SLM exhibit a superior pointing stability, better than 1 nm, which is comparable to that of non-holographic tweezers. These results suggest a means to implement precision force measurement experiments with holographic optical tweezers (HOTs).