Real-time monitoring of the silicidation process of tungsten filaments at high temperature used as catalysers for silane decomposition

The scope of this work is the systematic study of the silicidation process affecting tungsten filaments at high temperature (1900ºC) used for silane decomposition in the hot-wire chemical vapour deposition technique (HWCVD). The correlation between the electrical resistance evolution of the filaments, Rfil(t), and the different stages of the their silicidation process is exposed. Said stages correspond to: the rapid formation of two WSi2 fronts at the cold ends of the filaments and their further propagation towards the middle of the filaments; and, regarding the hot central portion of the filaments: a initial stage of silicon dissolution into the tungsten bulk, with a random duration for as-manufactured filaments, followed by the inhomogeneous nucleation of W5Si3 (which is later replaced by WSi2) and its further growth towards the filaments core. An electrical model is used to obtain real-time information about the current status of the filaments silicidation process by simply monitoring their Rfil(t) evolution during the HWCVD process. It is shown that implementing an annealing pre-treatment to the filaments leads to a clearly repetitive trend in the monitored Rfil(t) signatures. The influence of hydrogen dilution of silane on the filaments silicidation process is also discussed.

Large gypsum nodules in the Paleogene and Neogene evaporites of Spain: distribution and palaeogeographic significance

Sabkha and deep burial set tings are the most com mon sites where diagenetic anhydrite forms. In a sabkha setting, displacive facies (iso lated nodules, bed ded nodules, enterolithic levels) of early diagenetic or primary anhydrite are generated (Shearman, 1966; Hardie, 1967). These anhydrite facies are commonly foundat the top of shoal ing cycles representing the evolution from subaqueous depositional conditions at the base (carbonates, lutites) to exposure conditions at the top where in ter stitially-grown gypsum/anhydrite de velops ( sabkha cy cles). In a deep burial setting, gypsum transforms to tally to anhydrite with in creas ing temperature and lithostatic pressure (Murray, 1964). Al though this mineral transformation usually preserves the depositional gypsum facies, a significant textural change is in volved in other cases, resulting in replacive anhydrite with a nodular-mosaic or"chicken-wire" fabric (Warren, 2006). In the two settings, how ever, the size of the individual anhydrite nodules is relatively small, rarely reaching some tens of centimetres across. More over, bedding is preserved or little disturbed, al though minor de formation is caused by the displacive sabkha nodules.

Comments on "On the relationship between fractal dimension and the performance of multi-resonant dipole antennas using Koch curves"

Comentaris referits a l'article següent: K. J. Vinoy, J. K. Abraham, and V. K. Varadan, “On the relationshipbetween fractal dimension and the performance of multi-resonant dipoleantennas using Koch curves,” IEEE Transactions on Antennas and Propagation, 2003, vol. 51, p. 2296–2303.

Study of post-deposition contamination in low-temperature deposited polysilicon films

The presence of hydrogen in polysilicon films obtained at low temperatures by hot-wire CVD and the post-deposition oxidation by air-exposure of the films are studied in this paper. The experimental results from several characterization techniques (infrared spectroscopy, X-ray photoelectron spectroscopy, secondary ion mass spectrometry and wavelength dispersive spectroscopy) showed that hydrogen and oxygen are homogeneously distributed at grain boundaries throughout the depth of the films. Hydrogen is introduced during the growth process and its concentration is higher in samples deposited at lower temperatures. Oxygen diffuses along the grain boundaries and binds to silicon atoms, mainly in Si 2O groups.

Effect of water contamination on the shear bond strength of five orthodontic adhesives

Objectives: To evaluate the shear bond strength and site of failure of brackets bonded to dry and wet enamel. Study design: 50 teeth were divided into ten groups of 5 teeth each (10 surfaces). In half the groups enamel was kept dry before bonding, and in the other half distilled water was applied to wet the surface after etching. The following groups were established: 1)Acid/Transbond-XT (dry/wet) XT; 2) Transbond Plus Self Etching Primer (TSEP)/Transbond-XT paste (dry/wet); 3) Concise (dry), Transbond MIP/Concise (wet), 4) FujiOrtho-LC (dry/wet); 5) SmartBond (dry/wet). Brackets were bonded to both buccal and lingual surfaces. Specimens were stored in distilled water (24 hours at 37ºC) and thermocycled. Brackets were debonded using a Universal testing machine (cross-head speed 1 mm/min). Failure sites were classified using a stereomicroscope. Results: No significant differences in bond strength were detected between the adhesives under wet and dry conditions except for Smart- Bond, whose bond strength was significantly lower under dry conditions. For all the adhesives most bond failures were of mixed site location except for Smartbond, which failed at the adhesive-bracket interface. Conclusions: Under wet conditions the bonding capacity of the adhesives tested was similar than under dry conditions, with the exception of SmartBond which improved under wet conditions

Bioinspired electronic white cane implementation based on a LIDAR, a tri-axial accelerometer and a tactile belt

This work proposes the creation of a bioinspired electronic white cane for blind people using the whiskers principle for short-range navigation and exploration. Whiskers are coarse hairs of an animal's face that tells the animal that it has touched something using the nerves of the skin. In this work the raw data acquired from a low-size terrestrial LIDAR and a tri-axial accelerometer is converted into tactile information using several electromagnetic devices configured as a tactile belt. The LIDAR and the accelerometer are attached to the user’s forearm and connected with a wire to the control unit placed on the belt. Early validation experiments carried out in the laboratory are promising in terms of usability and description of the environment.

Erupted odontomas: a report of three cases and review of the literature

Introduction: Odontomas are benign odontogenic tumors composed of enamel, dentine, cement and pulp tissue. They are usually clinically asymptomatic, but often associated with tooth eruption disturbances. In exceptional cases the odontoma erupts into the mouth. The present study reports three cases of odontomas erupted into the oral cavity and reviews the literature. Clinical cases: The first case was an 11-year-old girl with impacted 4.6 associated to a radiopaque mass measuring about 2 cm in diameter. The histological diagnosis was complex odontoma. A clinical and radiological follow-up of 4.6 was carried out until its spontaneous eruption. The second case was a 26-year-old male presenting a hard, yellowish-brown mass located distal to the upper left second molar. Computed tomography confi rmed the presence of a radiopaque lesion, and the histopathological study confirmed a complex odontoma. The third patient was a 27-year-old male reporting tongue irritation due to tooth eruption in the inferior lingual region. A periapical radiograph revealed a mixed radiopaque lesion associated to impacted 3.2. The histological report in this case indicated a compound odontoma. Discussion: Odontomas erupting into the oral cavity are rare. The first case was published in 1980, and since then only 17 cases have been reported in the literature. Eight of the 17 cases were complex odontomas; the rest were compound odontomas. Pain, swelling and infection were the most common symptoms, and 13 cases presented an impacted tooth associated with the lesion

Morbilidad de la extracción de los terceros molares en pacientes entre los 12 y 18 años de edad

Objetivo: El propósito de este estudio fue analizar la incidencia de complicaciones después de la extracción quirúrgica de los terceros molares en pacientes de 12 a 18 años de edad. Pacientes y método: Se realizó un estudio retrospectivo de 390 extracciones quirúgicas de terceros molares superiores e inferiores en 173 pacientes en edades comprendidas entre los 12 y 18 años de edad, intervenidos bajo anestesia locorregional en el año 2000 en el Máster de Cirugía Bucal e Implantología Bucofacial de la Universidad de Barcelona. Los pacientes fueron divididos en tres grupos (A: 12-14 años, B:15-16 años, C: 17-18 años). Se registró la edad y el sexo del paciente, el motivo de la extracción, el grado de desarrollo dentario, la posición, la angulación y la inclusión del tercer molar. Finalmente se valoró la asociación entre dichas variables y la aparición de complicaciones postoperatorias. Resultados: La mayoría de los pacientes intervenidos fueron del sexo femenino (66,9%), y el grupo de edad en la que se realizó el mayor número de extracciones (62,8%) fue en el grupo C (17-18 años). El principal motivo de extracción fue la indicación por parte del ortodoncista (40,5%), seguido por la indicación profiláctica (39,5%). La presencia de clínica fue el motivo de extracción en un 20% de los casos. Se observó una incidencia del 15,6% de complicaciones postoperatorias tras la extracción de 390 terceros molares. En el grupo A el riesgo de complicaciones fue de 17,4%, en el grupo B de 19% y en el grupo C de 13,7%. Todas las complicaciones fueron reversibles y de corta duración como el dolor y la inflamación persistente, la infección, el trismo y la equimosis. Se presentó un caso de parestesia del nervio dentario inferior y un caso de parestesia del nervio lingual que remitieron a los 2 meses y al mes respectivamente. Conclusiones: este estudio demuestra que no hay diferencias significativas en las complicaciones observadas entre los tres grupos de edad, y por lo general, éstas son leves y reversibles. Se observó una mayor tendencia de complicaciones en las mujeres y el porcentaje de complicaciones aumenta cuanto menor es el espacio disponible para la erupción

Optimization of KOH etching process to obtain textured substrates suitable for heterojunction solar cells fabricated by HWCVD

In this work, we have studied the texturization process of (100) c-Si wafers using a low concentration potassium hydroxide solution in order to obtain good quality textured wafers. The optimization of the etching conditions have led to random but uniform pyramidal structures with good optical properties. Then, symmetric heterojunctions were deposited by Hot-Wire CVD onto these substrates and the Quasi-Steady-State PhotoConductance technique was used to measure passivation quality. Little degradation in the effective lifetime and implicit open circuit voltage of these devices (< 20 mV) was observed in all cases. It is especially remarkable that for big uniform pyramids, the open-circuit voltage is comparable to the values obtained on flat substrates.

Control of doped layers in p-i-n microcrystalline solar cells fully deposited with HWCVD

In this paper, the influence of the deposition conditions on the performance of p-i-n microcrystalline silicon solar cells completely deposited by hot-wire chemical vapor deposition is studied. With this aim, the role of the doping concentration, the substrate temperature of the p-type layer and of amorphous silicon buffer layers between the p/i and i/n microcrystalline layers is investigated. Best results are found when the p-type layer is deposited at a substrate temperature of 125 °C. The dependence seen of the cell performance on the thickness of the i layer evidenced that the efficiency of our devices is still limited by the recombination within this layer, which is probably due to the charge of donor centers most likely related to oxygen.

Stafne bone cavity: a retrospective study of 11 cases

Objective: to describe the clinical and radiological characteristics of patients with Stafne bone cavity. Study design: a retrospective, observational study of 11 cases of Stafne bone cavity. After finding an imagine compatible with Stafne bone cavity in the Orthopantomograph® of 11 patients, a sialography of the mandibular gland was made in 3 cases, computerized tomography (CT) in 6 cases, and in 4 cases surgical intervention to confirm the diagnosis. Results: the average age was 51.5 years, predominantly males. The entity was diagnosed incidentally during a routine radiology in all cases. The sialography revealed glandular tissue within the defect, and the CT demonstrated the conservation of the lingual cortical and the peripheral origin of the lesion. Glandular tissue was found within the lesions of two of the patients who underwent surgery, and in the other two the cavity was empty. No progressive changes were found in any of the 11 cases. Conclusions: Stafne bone cavity was an incidental finding, presenting no evolutionary changes, and as such conservatory therapy based on periodic controls was indicated. Currently, complementary techniques such as CT are sufficient to establish a certain diagnosis.

Lower incisor dentoalveolar compensation and symphysis dimensions among Class I and III malocclusion patients with different facial vertical skeletal patterns

Objective: To compare lower incisor dentoalveolar compensation and mandible symphysis morphology among Class I and Class III malocclusion patients with different facial vertical skeletal patterns. Materials and Methods: Lower incisor extrusion and inclination, as well as buccal (LA) and lingual (LP) cortex depth, and mandibular symphysis height (LH) were measured in 107 lateral cephalometric x-rays of adult patients without prior orthodontic treatment. In addition, malocclusion type (Class I or III) and facial vertical skeletal pattern were considered. Through a principal component analysis (PCA) related variables were reduced. Simple regression equation and multivariate analyses of variance were also used. Results: Incisor mandibular plane angle (P < .001) and extrusion (P  =  .03) values showed significant differences between the sagittal malocclusion groups. Variations in the mandibular plane have a negative correlation with LA (Class I P  =  .03 and Class III P  =  .01) and a positive correlation with LH (Class I P  =  .01 and Class III P  =  .02) in both groups. Within the Class III group, there was a negative correlation between the mandibular plane and LP (P  =  .02). PCA showed that the tendency toward a long face causes the symphysis to elongate and narrow. In Class III, alveolar narrowing is also found in normal faces. Conclusions: Vertical facial pattern is a significant factor in mandibular symphysis alveolar morphology and lower incisor positioning, both for Class I and Class III patients. Short-faced Class III patients have a widened alveolar bone. However, for long-faced and normal-faced Class III, natural compensation elongates the symphysis and influences lower incisor position.

Top-gate microcrystalline silicon TFTs processed at low temperature (<200ºC)

N-type as well P-type top-gate microcrystalline silicon thin film transistors (TFTs) are fabricated on glass substrates at a maximum temperature of 200 °C. The active layer is an undoped μc-Si film, 200 nm thick, deposited by Hot-Wire Chemical Vapor. The drain and source regions are highly phosphorus (N-type TFTs) or boron (P-type TFTs)-doped μc-films deposited by HW-CVD. The gate insulator is a silicon dioxide film deposited by RF sputtering. Al-SiO 2-N type c-Si structures using this insulator present low flat-band voltage,-0.2 V, and low density of states at the interface D it=6.4×10 10 eV -1 cm -2. High field effect mobility, 25 cm 2/V s for electrons and 1.1 cm 2/V s for holes, is obtained. These values are very high, particularly the hole mobility that was never reached previously.

Retrospective study of 145 supernumerary teeth

Objective: The goal of the present retrospective study is to describe the distribution of the supernumerary teeth in a population of patients that have been attended at the Public Clinic of the Department of Oral Surgery. Background: Supernumerary teeth and multiple hyperdontia are usually associated with different syndromes, such as Gardner syndrome, or with facial fissures; however, they can appear in patients without any pathology. Their prevalence oscillates to 0.5-3.8% in patients with permanent teeth and to 0.35-0.6% in patients with primary teeth. Patients and Methods: A total of 36,057 clinical histories of patients that were admitted at the clinic between September of 1991 and March of 2003 were revised. The following data were extrapolated: age, sex, number of extracted supernumerary teeth, localization, morphology and type of supernumerary teeth. Consequently, 102 patients were included into the present study. Results: Of the 147 supernumerary teeth identified in the oral cavities of patients 145 were extracted. The most frequent supernumerary teeth identified were mesiodens (46.9%), followed by premolars (24.1%) and fourth molars or distal molars (18%). As for location, 74.5% of the supernumerary teeth were found in the superior maxillary bone and 46.9% of the supernumerary teeth were present in the palatine/lingual area. Heteromorphology was found in two thirds of the supernumerary teeth, with conical shape being the most frequent. Finally, 29.7% of the supernumerary teeth had occlusion with permanent teeth, and mesiodens were the predominating type of supernumerary teeth that showed this feature. Conclusions: Mesiodens very frequently cause retention of permanent incisors, which erupt spontaneously after the extraction of supernumerary teeth, if there is sufficient space in the dental arch and if they conserve the eruptive force. Generally, supernumerary premolars are eumorphic and are casually discovered during radiological exam, if not producing any symptomology.

Sensibility and taste alterations after impacted lower third molar extractions. A prospective cohort study

Objectives: To determine the incidence, severity and duration of lingual tactile and gustatory function impairments after lower third molar removal. Study Design: Prospective cohort study with intra-subject measures of 16 patients undergoing lower third molar extractions. Sensibility and gustatory functions were evaluated in each subject preoperatively, one week and one month after the extraction, using Semmes-Weinstein monofilaments and 5 different concentrations of NaCl, respectively. Additionally, all patients filled a questionnaire to assess subjective perceptions. Results: Although patients did not perceive any sensibility impairments, a statistically significant decrease was detected when Semmes-Weinstein monofilaments. This alteration was present at one week after the surgical procedure and fully recovered one month after the extraction. There were no variations regarding the gustatory function. Conclusions: Lower third molar removal under local anesthesia may cause light lingual sensibility impairment. Most of these alterations remain undetected to patients. These lingual nerve injuries are present one week after the extraction and recover one month after surgery. The taste seems to remain unaffected after these procedures.