Production of nanometric particles in radio frequency glow discharges in mixtures of silane and methane

The formation of silicon particles in rf glow discharges has attracted attention due to their effect as a contaminant during film deposition or etching. However, silicon and silicon alloy powders produced by plasma¿enhanced chemical vapor deposition (PECVD) are promising new materials for sintering ceramics, for making nanoscale filters, or for supporting catalytic surfaces. Common characteristics of these powders are their high purity and the easy control of their stoichiometry through the composition of the precursor gas mixture. Plasma parameters also influence their structure. Nanometric powders of silicon¿carbon alloys exhibiting microstructural properties such as large hydrogen content and high surface/volume ratio have been produced in a PECVD reactor using mixtures of silane and methane at low pressure (-1 Torr) and low frequency square¿wave modulated rf power (13.56 MHz). The a¿Si1¿xCx:H powders were obtained from different precursor gas mixtures, from R=0.05 to R=9, where R=[SiH4]/([SiH4]+[CH4]). The structure of the a¿Si1¿xCx:H powder was analyzed by several techniques. The particles appeared agglomerated, with a wide size distribution between 5 and 100 nm. The silane/methane gas mixture determined the vibrational features of these powders in the infrared. Silicon-hydrogen groups were present for every gas composition, whereas carbon¿hydrogen and silicon¿carbon bonds appeared in methane¿rich mixtures (R-0.6). The thermal desorption of hydrogen revealed two main evolutions at about 375 and 660¿°C that were ascribed to hydrogen bonded to silicon and carbon, respectively. The estimated hydrogen atom concentration in the sample was about 50%.

Morphological and Magnetic Properties of Superparamagnetic Carbon-Coated Fe Nanoparticles Produced by Arc Discharge.

Spherical carbon coated iron particles of nanometric diameter in the 510 nm range have been produced by arc discharge at near-atmospheric pressure conditions (using 58·10 4 Pa of He). The particles exhibit a crystalline dense iron core with an average diameter 7.4 ± 2.0 nm surrounded by a sealed carbon shell, shown by transmission electron microscopy (TEM), selected-area diffrac- tion (SAED), energy-dispersive X-ray analysis (STEM-EDX) and electron energy loss spectroscopy (EELS). The SAED, EDX and EELS results indicate a lack of traces of core oxidized phases showing an efficient protection role of the carbon shell. The magnetic properties of the nanoparticles have been investigated in the 5300 K temperature range using a superconducting quantum interference device (SQUID). The results reveal a superparamagnetic behaviour with an average monodomain diameter of 7.6 nm of the nanoparticles. The zero field cooled and field cooled (ZFC-FC)magnetization curves show a blocking temperature (TB)at room temperature very suitable for biomedical applications (drug delivery, magnetic resonance imaging MRI, hyperthermia).

A semi-grand canonical Monte Carlo simulation model for ion binding to ionizable surfaces: proton binding of carboxylated latex particles as a case study

In this paper, we present a computer simulation study of the ion binding process at an ionizable surface using a semi-grand canonical Monte Carlo method that models the surface as a discrete distribution of charged and neutral functional groups in equilibrium with explicit ions modelled in the context of the primitive model. The parameters of the simulation model were tuned and checked by comparison with experimental titrations of carboxylated latex particles in the presence of different ionic strengths of monovalent ions. The titration of these particles was analysed by calculating the degree of dissociation of the latex functional groups vs. pH curves at different background salt concentrations. As the charge of the titrated surface changes during the simulation, a procedure to keep the electroneutrality of the system is required. Here, two approaches are used with the choice depending on the ion selected to maintain electroneutrality: counterion or coion procedures. We compare and discuss the difference between the procedures. The simulations also provided a microscopic description of the electrostatic double layer (EDL) structure as a function of p H and ionic strength. The results allow us to quantify the effect of the size of the background salt ions and of the surface functional groups on the degree of dissociation. The non-homogeneous structure of the EDL was revealed by plotting the counterion density profiles around charged and neutral surface functional groups.

Interpolating and sampling sequences in finite Riemann surfaces

We provide a description of the interpolating and sampling sequences on a space of holomorphic functions on a finite Riemann surface, where a uniform growth restriction is imposed on the holomorphic functions.

Theory of Wetting-Induced Fluid Entrainment by Advancing Contact Lines on Dry Surfaces

We report on the onset of fluid entrainment when a contact line is forced to advance over a dry solid of arbitrary wettability. We show that entrainment occurs at a critical advancing speed beyond which the balance between capillary, viscous, and contact-line forces sustaining the shape of the interface is no longer satisfied. Wetting couples to the hydrodynamics by setting both the morphology of the interface at small scales and the viscous friction of the front. We find that the critical deformation that the interface can sustain is controlled by the friction at the contact line and the viscosity contrast between the displacing and displaced fluids, leading to a rich variety of wetting-entrainment regimes. We discuss the potential use of our theory to measure contact-line forces using atomic force microscopy and to study entrainment under microfluidic conditions exploiting colloid-polymer fluids of ultralow surface tension.

Carbon and nitrogen partitioning during post-anthesis is conditioned by N fertilization and sink strength in three cereals

Further knowledge of the processes conditioning nitrogen use efficiency (NUE) is of great relevance to crop productivity. The aim of this paper was characterise C and N partitioning during grain filling and their implications for NUE. Cereals such as bread wheat (Triticum aestivum L. cv Califa sur), triticale (× Triticosecale Wittmack cv. Imperioso) and tritordeum (× Tritordeum Asch. & Graebn line HT 621) were grown under low (LN, 5 mm NH4NO3) and high (HN, 15 mm NH4NO3) N conditions. We conducted simultaneous double labelling (12CO2 and 15NH415NO3) in order to characterise C and N partitioning during grain filling. Although triticale plants showed the largest total and ear dry matter values in HN conditions, the large investment in shoot and root biomass negatively affected ear NUE. Tritordeum was the only genotype that increased NUE in both N treatments (NUEtotal), whereas in wheat, no significant effect was detected. N labelling revealed that N fertilisation during post-anthesis was more relevant for wheat and tritordeum grain filling than for triticale. The study also revealed that the investments of C and N in flag leaves and shoots, together with the"waste" of photoassimilates in respiration, conditioned the NUE of plants, and especially under LN. These results suggest that C and N use by these plants needs to be improved in order to increase ear C and N sinks, especially under LN. It is also remarkable that even though tritordeum shows the largest increase in NUE, the low yield of this cereal limits its agronomic value.

Seasonal dynamics and net production of disolved organic carbon in an oligotrophic coastal environment

To understand dissolved organic carbon (DOC) seasonal dynamics in a coastal oligotrophic site in the north-western Mediterranean Sea, we monitored DOC concentrations monthly over 3 yr, together with the meteorological data and the food-web-related biological processes involved in DOC dynamics. Additional DOC samples were taken in several inshore−offshore transects along the Catalan coast. We found DOC concentrations of ~60 µmol C l−1 in winter, with increasing values through the summer and autumn and reaching 100 to 120 µmol C l−1 in November. There was high inter-annual variability in this summer DOC accumulation, with values of 36, 69 and 13 µmol C l−1 for 2006, 2007 and 2008, respectively. The analysis of the microbial food-web processes involved in the DOC balance did not reveal the causes of this accumulation, since the only occasion on which we observed net DOC production (0.3 ± 1 µmol C l−1 d−1 on average) was in 2007, and the negative DOC balance of 2006 and 2008 did not prevent DOC accumulating. The DOC accumulation episodes coincided with low rates of water renewal (average 0.037 ± 0.021 d−1 from May to October) compared with those of winter to early spring (average 0.11 ± 0.048 d−1 from November to April). Indeed, the amount of DOC accumulated each year was inversely correlated with the average summer rainfall. We hypothesize that decreased DOC turn-over due to photochemical or biological processes mostly active during the summer and low water renewal rate combine to determine seasonal DOC accumulation and influence its inter-annual variability.

Growth and functionalization of carbon nanotubes on quartz filter for environmental applications

Background: Air pollution has become an important issue worldwide due to its adverse health effects. Among the different air contaminants, volatile organic compounds (VOCs) are liquids or solids with a high vapor pressure at room temperature that are extremely dangerous for human health. Removal of these compounds can be achieved using nanomaterials with tailored properties such as carbon nanotubes. Methods: Vertically-aligned multiwall carbon nanotubes (CNTs) were successfully grown on quartz filters by means of plasma enhanced chemical vapor deposition (PECVD). Furthermore, a plasma treatment was performed in order to modify the surface properties of the CNTs. The adsorption/desorption processes of three chlorinated compounds (trichloroethylene, 1,2-dichlorobenzene and chloroform) on the CNTs were studied using mass spectrometry measurements with a residual gas analyzer. Results: The adsorption capability of the CNTs increased after functionalization of their surface with a water plasma treatment. In addition, it was found that the presence of aromatic rings, water solubility and polarity of the VOCs play an important role on the adsorption/desorption kinetics at the CNTs surface. Conclusions: This study demonstrates the applicability of CNTs deposited on quartz filters for the removal or selective detection of volatile organic compounds (VOCs). The presence of aromatic rings in VOCs results in π -stacking interactions with a significant increase of their adsorption. On the other hand, it was found that CNTs surface interactions increase with water solubility and polarity of the VOC.

The global carbon budget:a conflicting claims problem

Despite global environmental governance has traditionally couched global warming in terms of annual CO2 emissions (a flow), global mean temperature is actually determined by cumulative CO2 emissions in the atmosphere (a stock). Thanks to advances of scientific community, nowadays it is possible to quantify the \global carbon budget", that is, the amount of available cumulative CO2 emissions before crossing the 2oC threshold (Meinshausen et al., 2009). The current approach proposes to analyze the allocation of such global carbon budget among countries as a classical conflicting claims problem (O'Neill, 1982). Based on some appealing principles, it is proposed an efficient and sustainable allocation of the available carbon budget from 2000 to 2050 taking into account different environmental risk scenarios. Keywords: Carbon budget, Conflicting claims problem, Distribution, Climate change. JEL classification: C79, D71, D74, H41, H87, Q50, Q54, Q58.

Stable carbon isotopes in archaeobotanical remains and palaeoclimate

Es descriu una metodologia recent per a inferir la precipitació en el passat basada en l’anàlisi de la composició isotòpica del carboni (δ13C) en restes arqueobotàniques. Un cop descrita la base fisiològica de la tècnica, s’il·lustra l’aplicabilitat de δ13C mitjançant un exemple referent al NE peninsular. Hom pretén proporcionar una estimació quantitativa de l’evolució de la precipitació estacional (primavera) i anual al llarg dels darrers quatre mil anys basada en δ13C. Les mostres analitzades comprenen carbons (pi blanc) i llavors carbonitzades (blat i ordi), i s’obtenen estimes pluviomètriques superiors en el passat que actualment, amb una tendència gradual cap a condicions progressivament més àrides. No obstant això, aquesta tendència no esdevé uniforme, i es detecten dues fases de major precipitació (1800-900 aC; 300 aC - 300 dC) alternadament amb períodes relativament secs (900-300 aC; 900 dC - present). Dels resultats presentats també es desprèn que la importància relativa de la pluja primaveral en el passat fou variable. Des d’aproximadament el 300 aC en endavant, el període primaveral subministrà una major proporció de pluja anual que actualment. Contràriament, durant el període 1800-800 dC la seva contribució va esdevenir inferior, i va aparèixer una fase transitòria (800-300 aC) que mostra una recuperació sobtada en aportació primaveral. Posteriorment a aquesta fase la sincronia de canvis en δ13C en granes i carbons suggereix l’arribada del clima mediterrani a la regió.

Grain yield, carbon isotope discrimination and mineral content in mature kernels of barley under irrigated and rainfed conditions

The relationship between yield, carbon isotope discrimination and ash content in mature kernels was examined for a set of 13 barley (Hordeum vulgare) cultivars. Plants were grown under rainfed and well-irrigated conditions in a Mediterranean area. Water deficit caused a decrease in both grain yield and carbon isotope discrimination (Δ). The yield was positively related to Δ and negatively related to ash content, across genotypes within each treatment. However, whereas the correlation between yield and Δ was higher for the set of genotypes under well-irrigated (r=0.70, P<0.01) than under rainfed (r=0.42) conditions, the opposite occurred when yield and ash content were related, ie r=-0.38 under well-irrigated and r=-0.73, (P<0.01) under rainfed conditions. Carbon isotope discrimination and ash content together account for almost 60% of the variation in yield, in both conditions. There was no significant relationship (r=-0.15) between carbon isotope discrimination and ash content in well-irrigated plants, whereas in rainfed plants, this relationship, although significant (r=-0.54, P< 0.05), was weakly negative. The concentration of several mineral elements was measured in the same kernels. The mineral that correlated best with ash content, yield and A, was K. For yield and Δ, although the relationship with K followed the same pattern as the relationhip with ash content, the correlation coefficients were lower. Thus, mineral accumulation in mature kernels seems to be independent of transpiration efficiency. In fact, filling of grains takes place through the phloem pathway. The ash content in kernels is proposed as a complementary criterion, in addition to kernel Δ, to assess genotype differences in barley grain yield under rainfed conditions.

Genetic variation for carbon isotope composition in Juglans regia L.: relationships with growth, phenology and climate of origin

Among the traits of breeding interest for the common walnut tree Juglans regia L., characteristics such as timing of budbreak and leaf fall, water-use efficiency and growth performance are regarded as being of utmost relevance in Mediterranean conditions. The authors evaluated intraspecific variation in $\delta$13C (carbon isotope composition, surrogate of intrinsic water-use efficiency, WUE$_{\rm i}$) for 22 J. regia families grown in a progeny test under supplementary irrigation, and investigated whether such variation correlated with climatic indicators of native habitats. The genetic relationships between $\delta$13C, growth and phenology were also assessed during two consecutive years. Overall, the most water-use-efficient families (i.e. with higher $\delta$13C), which originated mainly from drought-prone provenance regions which have a high vapour pressure deficit and low rainfall, exhibited less height growth and smaller DBH. Using a stepwise regression procedure, $\delta$13C was included as the main explanatory variable of genotypic variation in growth traits, together with growing season duration (for DBH in both years) and flushing (for height in 2007). It was concluded that WUE$_{\rm i}$ is largely unconnected to phenology effects in the explanation of growth performance for J. regia, therefore suggesting the opportunity of simultaneously selecting for low WUE$_{\rm i}$ and extended growing period to maximise productivity in non-water-limited environments.

Characterisation of the LMS200 laser beam under the influence of blockage surfaces. Influence on 3D scanning of tree orchards

The geometric characterisation of tree orchards is a high-precision activity comprising the accurate measurement and knowledge of the geometry and structure of the trees. Different types of sensors can be used to perform this characterisation. In this work a terrestrial LIDAR sensor (SICK LMS200) whose emission source was a 905-nm pulsed laser diode was used. Given the known dimensions of the laser beam cross-section (with diameters ranging from 12 mm at the point of emission to 47.2 mm at a distance of 8 m), and the known dimensions of the elements that make up the crops under study (flowers, leaves, fruits, branches, trunks), it was anticipated that, for much of the time, the laser beam would only partially hit a foreground target/object, with the consequent problem of mixed pixels or edge effects. Understanding what happens in such situations was the principal objective of this work. With this in mind, a series of tests were set up to determine the geometry of the emitted beam and to determine the response of the sensor to different beam blockage scenarios. The main conclusions that were drawn from the results obtained were: (i) in a partial beam blockage scenario, the distance value given by the sensor depends more on the blocked radiant power than on the blocked surface area; (ii) there is an area that influences the measurements obtained that is dependent on the percentage of blockage and which ranges from 1.5 to 2.5 m with respect to the foreground target/object. If the laser beam impacts on a second target/object located within this range, this will affect the measurement given by the sensor. To interpret the information obtained from the point clouds provided by the LIDAR sensors, such as the volume occupied and the enclosing area, it is necessary to know the resolution and the process for obtaining this mesh of points and also to be aware of the problem associated with mixed pixels.