Unusual voltage sag event detection in power systems

Three multivariate statistical tools (principal component analysis, factor analysis, analysis discriminant) have been tested to characterize and model the sags registered in distribution substations. Those models use several features to represent the magnitude, duration and unbalanced grade of sags. They have been obtained from voltage and current waveforms. The techniques are tested and compared using 69 registers of sags. The advantages and drawbacks of each technique are listed

Estimation of zero-sequence impedance of undergrounds cables for single-phase fault location in distribution systems with electric arc

This paper focus on the problem of locating single-phase faults in mixed distribution electric systems, with overhead lines and underground cables, using voltage and current measurements at the sending-end and sequence model of the network. Since calculating series impedance for underground cables is not as simple as in the case of overhead lines, the paper proposes a methodology to obtain an estimation of zero-sequence impedance of underground cables starting from previous single-faults occurred in the system, in which an electric arc occurred at the fault location. For this reason, the signal is previously pretreated to eliminate its peaks voltage and the analysis can be done working with a signal as close as a sinus wave as possible

Classification of sags according to their origin based on the waveform similarity

A statistical method for classification of sags their origin downstream or upstream from the recording point is proposed in this work. The goal is to obtain a statistical model using the sag waveforms useful to characterise one type of sags and to discriminate them from the other type. This model is built on the basis of multi-way principal component analysis an later used to project the available registers in a new space with lower dimension. Thus, a case base of diagnosed sags is built in the projection space. Finally classification is done by comparing new sags against the existing in the case base. Similarity is defined in the projection space using a combination of distances to recover the nearest neighbours to the new sag. Finally the method assigns the origin of the new sag according to the origin of their neighbours

La evaluación entre iguales en el grado de educación social. Aproximación a la vida profesional

La relación educativa entraña, inevitablemente, el debate entorno de la verticalidad y del ejercicio del poder. De qué modo nos relacionamos y cómo gestionamos la comunicación entre educadores y educandos, así como entre iguales. Esa tensión se ve amplificada en la medida que incorporamos lógicas evaluativas en nuestro quehacer profesional. La siguiente comunicación describe la experiencia de la metodología de aprendizaje basada en la evaluación entre iguales aplicada a la profesionalización de los y las educadores/as sociales. Tanto a nivel escolar como en el universitario hay numerosas experiencias publicadas en relación a la metodología de evaluación entre iguales. Además, existen numerosos apartados de los “Documentos profesionalizadores” donde se justifica el hecho de que se entrenen algunas habilidades que deberían darse en la práctica profesional (como por ejemplo en la definición, en el código ético, y en el catálogo de funciones y competencias del/la educador/a social). En esta comunicación pretendemos dar a conocer la experiencia de entrenamiento de futuros educadores en aspectos que tienen una relación directa con la evaluación entre educadores/as sociales. Así pues, utilizaremos una justificación académica y metodológica de la actividad, enlazándola con los documentos profesionalizadores con un fin relacionado directamente con el ejercicio de la profesión.

Redisseny d’una línia d’alta tensió comparant el traçat aeri amb el traçat soterrat

A petició d’un grup d’empreses del polígon industrial “Polígon”, es redacta el presentprojecte que té per objecte establir les característiques tècniques per a la construcció d’una variant de la línia de doble circuit 110 kV que uneix les dues subestacions; S.E. Polígon Nord – S.E. Polígon Sur. Actualment es disposa d’una línia de doble circuit 110 kV que uneix les dues subestacions; S.E. Polígon Nord – S.E. Polígon Sur i que travessa vàries parcel•les del polígon industrial “Polígon” sobrevolant-les i reduint, per tant, la seva capacitat d’aprofitament de sòl. Es consideraran, i es calcularan, les dues alternatives que existeixen actualment en línies de transport elèctric: variant aèria i variant soterrada

Biomechanical wall properties of human intracranial aneurysms resected following surgical clipping (IRRAs Project)

Background and purpose: Individual rupture risk assessment of intracranial aneurysms is a major issue in the clinical management of asymptomatic aneurysms. Aneurysm rupture occurs when wall tension exceeds the strength limit of the wall tissue. At present, aneurysmal wall mechanics are poorly understood and thus, risk assessment involving mechanical properties is inexistent. Aneurysm computational hemodynamics studies make the assumption of rigid walls, an arguable simplification. We therefore aim to assess mechanical properties of ruptured and unruptured intracranial aneurysms in order to provide the foundation for future patient-specific aneurysmal risk assessment. This work also challenges some of the currently held hypotheses in computational flow hemodynamics research. Methods: A specific conservation protocol was applied to aneurysmal tissues following clipping and resection in order to preserve their mechanical properties. Sixteen intracranial aneurysms (11 female, 5 male) underwent mechanical uniaxial stress tests under physiological conditions, temperature, and saline isotonic solution. These represented 11 unruptured and 5 ruptured aneurysms. Stress/strain curves were then obtained for each sample, and a fitting algorithm was applied following a 3-parameter (C(10), C(01), C(11)) Mooney-Rivlin hyperelastic model. Each aneurysm was classified according to its biomechanical properties and (un)rupture status.Results: Tissue testing demonstrated three main tissue classes: Soft, Rigid, and Intermediate. All unruptured aneurysms presented a more Rigid tissue than ruptured or pre-ruptured aneurysms within each gender subgroup. Wall thickness was not correlated to aneurysmal status (ruptured/unruptured). An Intermediate subgroup of unruptured aneurysms with softer tissue characteristic was identified and correlated with multiple documented risk factors of rupture. Conclusion: There is a significant modification in biomechanical properties between ruptured aneurysm, presenting a soft tissue and unruptured aneurysms, presenting a rigid material. This finding strongly supports the idea that a biomechanical risk factor based assessment should be utilized in the to improve the therapeutic decision making.

Ethics Outside, Within, or Beyond OR Models

Since ethical concerns are calling for more attention within Operational Research, we present three approaches to combine Operational Research models with ethics. Our intention is to clarify the trade-offs faced by the OR community, in particular the tension between the scientific legitimacy of OR models (ethics outside OR models) and the integration of ethics within models (ethics within OR models). Presenting and discussing an approach that combines OR models with the process of OR (ethics beyond OR models), we suggest rigorous ways to express the relation between ethics and OR models. As our work is exploratory, we are trying to avoid a dogmatic attitude and call for further research. We argue that there are interesting avenues for research at the theoretical, methodological and applied levels and that the OR community can contribute to an innovative, constructive and responsible social dialogue about its ethics.

Ethics outside, within or beyond OR models

Since ethical concerns are calling for more attention within OperationalResearch, we present three approaches to combine Operational Researchmodels with ethics. Our intention is to clarify the trade-offs faced bythe OR community, in particular the tension between the scientificlegitimacy of OR models (ethics outside OR models) and the integrationof ethics within models (ethics within OR models). Presenting anddiscussing an approach that combines OR models with the process of OR(ethics beyond OR models), we suggest rigorous ways to express the relationbetween ethics and OR models. As our work is exploratory, we are trying toavoid a dogmatic attitude and call for further research. We argue thatthere are interesting avenues for research at the theoretical,methodological and applied levels and that the OR community can contributeto an innovative, constructive and responsible social dialogue about itsethics.

The organization of research corporations and researcher ability

This paper analyzes the formation of Research Corporations as an alternative governance structure for performing R&D compared to pursuing in-house R&D projects. Research Corporations are privatefor-profit research centers that bring together several firms with similar research goals. In a Research Corporation formal authority over the choice of projects is jointly exercised by the top management of the member firms. A private for-profit organization cannot commit not to interfere with the project choice of the researchers. However, increasing the number of member firms of the Research Corporation reduces the incentive of member firms to meddle with the research projects of researchers because exercising formal authority over the choice of research projects is a public good. The Research Corporation thus offers researchers greater autonomy than a single firm pursuing an identical research program in its in-house R&D department. This attracts higher ability researchers to the Research Corporation compared to the internal R&D department. The paper uses the theoretical model to analyze the organization of the Microelectronics and Computer Technology Corporation (MCC). The facts of this case confirm the existence of a tension between control over the choice of research projects and the ability of researchers that the organization is able to attract or hold onto.

An economic theory of church strictness

This paper makes several contributions to the growing literatureon the economics of religion. First, we explicitly introduce spatial-location models into the economics of religion. Second, we offer a newexplanation for the observed tendency of state (monopoly) churches tolocate toward the "low-tension" end of the "strictness continuum" (ina one-dimensional product space): This result is obtained through theconjunction of "benevolent preferences" (denominations care about theaggregate utility of members) and asymmetric costs of going to a moreor less strict church than one prefers.We also derive implications regarding the relationship between religiousstrictness and membership. The driving forces of our analysis, religiousmarket interactions and asymmetric costs of membership, high-light newexplanations for some well-established stylized facts. The analysis opensthe way to new empirical tests, aimed at confronting the implications ofour model against more traditional explanations.

La première génération d’écrivains d’origine amazighe dans la littérature catalane: Laila Karrouch (Nador, 1977) et Najat El Hachmi (Nador, 1979). Leur signification et valeur.

La Catalogne a accueilli entre la fin du XXe siècle et le début du XXIe siècle une importante vague d’immigrés aux origines les plus diverses. Les Marocains ont constitué le premier flot de cette vague et ont donné naissance, par le biais des oeuvres de Laila Karrouch et de Najat El Hachmi, à une littérature pionnière construite dans la tension entre deux mondes, le Maghreb et la Catalogne. Cette littérature, faite d’expériences vécues profondes, va permettre à beaucoup d’autres, à la fois, de garder leur identité et de se sentir citoyens de leur nouveau pays.

Eficiència energètica aplicada a les instal·lacions de la Universitat de Vic

En termes generals, es pot definir l’Eficiència Energètica com la reducció del consum d’energia mantenint els mateixos serveis energètics, sense disminuir el nostre confort i qualitat de vida, protegint el medi ambient, assegurant el proveïment i fomentant un comportament Sostenible al seu ús. L’objectiu principal d’aquest treball, és reduir el consum d’energia i terme de potència contractat a la Universitat de Vic, aplicant un programa d’estalvi amb mesures correctores en el funcionament de les seves instal·lacions o espais. Per tal de poder arribar a aquest objectiu marcat, prèviament s’ha realitzat un estudi acurat, obtenint tota la informació necessària per poder aplicar les mesures correctores a la bossa més important de consum. Un cop trobada, dur a terme l’estudi de la viabilitat de la inversió de les mesures correctores més eficients, optimitzant els recursos destinats. L’espai on s’ha dut a terme l’estudi, ha estat a l’edifici F del Campus Miramarges, seguint les indicacions d’Arnau Bardolet (Cap de Manteniment de la UVIC). Aquest edifici consta d’un entresol, baixos i quatre plantes. L’equip de mesura que s’ha fet servir per realitzar l’estudi, és de la marca Circutor sèrie AR5-L, aquests equips són programables que mesuren, calculen i emmagatzemen en memòria els principals paràmetres elèctrics en xarxes trifàsiques. Els projectes futurs complementaris que es podrien realitzar a part d’aquest són: instal·lar sensors, instal·lar mòduls convertidors TCP/IP, aprofitar la xarxa intranet i crear un escada amb un sinòptic de control i gestió des d’un punt de treball. Aquest aplicatiu permet visualitzar en una pantalla d’un PC tots els estats dels elements controlats mitjançant un sinòptic (encendre/parar manualment l’enllumenat i endolls de les aules, estat d’enllumenat i endolls de les aules, consums instantanis/acumulats energètics, estat dels passadissos entre altres) i explotar les dades recollides a la base de dades. Cada espai tindria la seva lògica de funcionament automàtic específic. Entre les conclusions més rellevants obtingudes en aquest treball s’observa: · Que és pot reduir la potència contractada a la factura a l’estar per sota de la realment consumida. · Que no hi ha penalitzacions a la factura per consum de reactiva, ja que el compensador funciona correctament. · Que es pot reduir l’horari de l’inici del consum d’energia, ja que no correspon a l’activitat docent. · Els valors de la tensió i freqüència estan dintre de la normalitat. · Els harmònics estan al llindar màxim. Analitzant aquestes conclusions, voldria destacar les mesures correctores més importants que es poden dur a terme: canvi tecnològic a LED, temporitzar automàticament l’encesa i apagada dels fluorescents i equips informàtics de les aules “seguint calendari docent”, instal·lar sensors de moviment amb detecció lumínica als passadissos. Totes les conclusions extretes d’aquest treball, es poden aplicar a tots els edificis de la facultat, prèviament realitzant l’estudi individual de cadascuna, seguint els mateixos criteris per tal d’optimitzar la inversió.

Mapping cell-matrix stresses during stretch reveals inelastic reorganization of the cytoskeleton.

The mechanical properties of the living cell are intimately related to cell signaling biology through cytoskeletal tension. The tension borne by the cytoskeleton (CSK) is in part generated internally by the actomyosin machinery and externally by stretch. Here we studied how cytoskeletal tension is modified during stretch and the tensional changes undergone by the sites of cell-matrix interaction. To this end we developed a novel technique to map cell-matrix stresses during application of stretch. We found that cell-matrix stresses increased with imposition of stretch but dropped below baseline levels on stretch release. Inhibition of the actomyosin machinery resulted in a larger relative increase in CSK tension with stretch and in a smaller drop in tension after stretch release. Cell-matrix stress maps showed that the loci of cell adhesion initially bearing greater stress also exhibited larger drops in traction forces after stretch removal. Our results suggest that stretch partially disrupts the actin-myosin apparatus and the cytoskeletal structures that support the largest CSK tension. These findings indicate that cells use the mechanical energy injected by stretch to rapidly reorganize their structure and redistribute tension.

Thrombin-induced contraction in alveolar epithelial cells probed by traction microscopy

Contractile tension of alveolar epithelial cells plays a major role in the force balance that regulates the structural integrity of the alveolar barrier. The aim of this work was to study thrombin-induced contractile forces of alveolar epithelial cells. A549 alveolar epithelial cells were challenged with thrombin, and time course of contractile forces was measured by traction microscopy. The cells exhibited basal contraction with total force magnitude 55.0 ± 12.0 nN (mean ± SE, n = 12). Traction forces were exerted predominantly at the cell periphery and pointed to the cell center. Thrombin (1 U/ml) induced a fast and sustained 2.5-fold increase in traction forces, which maintained peripheral and centripetal distribution. Actin fluorescent staining revealed F-actin polymerization and enhancement of peripheral actin rim. Disruption of actin cytoskeleton with cytochalasin D (5 µM, 30 min) and inhibition of myosin light chain kinase with ML-7 (10 µM, 30 min) and Rho kinase with Y-27632 (10 µM, 30 min) markedly depressed basal contractile tone and abolished thrombin-induced cell contraction. Therefore, the contractile response of alveolar epithelial cells to the inflammatory agonist thrombin was mediated by actin cytoskeleton remodeling and actomyosin activation through myosin light chain kinase and Rho kinase signaling pathways. Thrombin-induced contractile tension might further impair alveolar epithelial barrier integrity in the injured lung.

Two-dimensional clusters of liquid 4He

The binding energies of two-dimensional clusters (puddles) of¿4He are calculated in the framework of the diffusion Monte Carlo method. The results are well fitted by a mass formula in powers of x=N-1/2, where N is the number of particles. The analysis of the mass formula allows for the extraction of the line tension, which turns out to be 0.121 K/Å. Sizes and density profiles of the puddles are also reported.