Plasma-enhanced chemical vapor deposition of boron nitride thin films from B2H6-H2-NH3 and B2H6-N2 gas mixtures

Highly transparent and stoichiometric boron nitride (BN) films were deposited on both electrodes (anode and cathode) of a radio-frequency parallel-plate plasma reactor by the glow discharge decomposition of two gas mixtures: B2H6-H2-NH3 and B2H6-N2. The chemical, optical, and structural properties of the films, as well as their stability under long exposition to humid atmosphere, were analyzed by x-ray photoelectron, infrared, and Raman spectroscopies; scanning and transmission electron microscopies; and optical transmittance spectrophotometry. It was found that the BN films grown on the anode using the B2H6-H2-NH3 mixture were smooth, dense, adhered well to substrates, and had a textured hexagonal structure with the basal planes perpendicular to the film surface. These films were chemically stable to moisture, even after an exposition period of two years. In contrast, the films grown on the anode from the B2H6-N2 mixture showed tensile stress failure and were very unstable in the presence of moisture. However, the films grown on the cathode from B2H6-H2-NH3 gases suffered from compressive stress failure on exposure to air; whereas with B2H6-N2 gases, adherent and stable cathodic BN films were obtained with the same crystallographic texture as anodic films prepared from the B2H6-H2-NH3 mixture. These results are discussed in terms of the origin of film stress, the effects of ion bombardment on the growing films, and the surface chemical effects of hydrogen atoms present in the gas discharge.

A fully automated hot-wall multiplasma-monochamber reactor for thin film deposition

We present a study on the development and the evaluation of a fully automated radio-frequency glow discharge system devoted to the deposition of amorphous thin film semiconductors and insulators. The following aspects were carefully addressed in the design of the reactor: (1) cross contamination by dopants and unstable gases, (2) capability of a fully automated operation, (3) precise control of the discharge parameters, particularly the substrate temperature, and (4) high chemical purity. The new reactor, named ARCAM, is a multiplasma-monochamber system consisting of three separated plasma chambers located inside the same isothermal vacuum vessel. Thus, the system benefits from the advantages of multichamber systems but keeps the simplicity and low cost of monochamber systems. The evaluation of the reactor performances showed that the oven-like structure combined with a differential dynamic pumping provides a high chemical purity in the deposition chamber. Moreover, the studies of the effects associated with the plasma recycling of material from the walls and of the thermal decomposition of diborane showed that the multiplasma-monochamber design is efficient for the production of abrupt interfaces in hydrogenated amorphous silicon (a-Si:H) based devices. Also, special attention was paid to the optimization of plasma conditions for the deposition of low density of states a-Si:H. Hence, we also present the results concerning the effects of the geometry, the substrate temperature, the radio frequency power and the silane pressure on the properties of the a-Si:H films. In particular, we found that a low density of states a-Si:H can be deposited at a wide range of substrate temperatures (100°C

Nanoparticles in SiH4-Ar plasma: Modelling and comparison with experimental data

Experimental and theoretical investigations for growth of silicon nanoparticles (4 to 14 nm) in radio frequency discharge were carried out. Growth processes were performed with gas mixtures of SiH4 and Ar in a plasma chemical reactor at low pressure. A distinctive feature of presented kinetic model of generation and growth of nanoparticles (compared to our earlier model) is its ability to investigate small"critical" dimensions of clusters, determining the rate of particle production and taking into account the influence of SiH2 and Si2Hm dimer radicals. The experiments in the present study were extended to high pressure (≥20 Pa) and discharge power (≥40 W). Model calculations were compared to experimental measurements, investigating the dimension of silicon nanoparticles as a function of time, discharge power, gas mixture, total pressure, and gas flow.

Application of ultrasound in bone surgery: two case reports

The present study describes some of the applications of ultrasound in bone surgery, based on the presentation of two clinical cases. The Piezosurgery® ultrasound device was used (Tecnología Mectron Medical, Carasco, Italy). In one case the instrument was used to harvest a chin bone graft for placement in a bone defect at level 1.2, while in the other case a bony window osteotomy was made in the external wall of the maxillary sinus, in the context of a sinus membrane lift procedure. The Piezosurgery® device produces specific ultrasound frequency modulation (25-29 kHz), and has been designed to secure increased precision in application to bone surgery. This instrument produces selective sectioning of the mineralized bone structures, and causes less intra- and postoperative bleeding. One of the advantages of the Piezosurgery® device is that it can be used for maxillary sinus lift procedures in dental implant placement. In this context it considerably lessens the risk of sinus mucosa laceration by preparing the bony window in the external wall of the upper maxilla, and can be used to complete the lifting maneuver. The use of ultrasound in application to hard tissues can be regarded as a slow technique compared with the conventional rotary instruments, since it requires special surgical skill and involves a certain learning curve.

Disseny de circuit de proves de traçabilitat amb rfid

ITENE és un institut tecnològic de recerca situat a Paterna (València). Té una plantapilot especialitzada en logística on les empreses que ho vulguin (mitjançant convenis,en règim de lloguer, etc.), poden utilitzar les instal•lacions (magatzem intel•ligent,aplicacions RFID, etc.), per provar els seus productes i simular processos de logística itraçabilitat.En aquesta planta s'ha detectat la necessitat de poder provar nous productes cometiquetes, detectors i processadors equipats amb tecnologia RFID (Identificació perRadiofreqüència). Aquesta tecnologia consisteix en passar informació que conté unaetiqueta “intel•ligent” cap a un terminal (PC) mitjançant uns detectors que, perproximitat, poden llegir la informació. Per exemple, quan un camió ple de mercaderiesprèviament etiquetades, passa per un pòrtic amb detectors RFID, es genera unainformació que passa directament a un terminal. Al moment es pot saber què porta elcamió, quantitat, color, mides, etc. Si això es combina amb un ERP, es pot descomptarde l'estoc en temps real. De fet s'utilitza per moltes aplicacions logística, control deprocessos de fabricació, traçabilitat de productes, etc.Per aquest motiu, ITENE, mitjançant el contacte de AIFOS SOLUTIONS S.L (empresaespecialitzada en RFID) ha encarregat un sistema de transportadors de banda per provarnoves solucions.L'objecte del present projecte consisteix en el disseny i automatització d'un sistema de 4cintes transportadores 2 elevadors per tal de fer un circuit tancat per moure caixes en un“bucle” de forma automàtica. L'objectiu és “llençar” caixes plenes de productes (etiquetats amb RFID) mitjançant untransportador equipat amb un pòrtic que té instal•lats diversos detectors de radiofreqüència,i poder-ne provar la correcta detecció a diferents velocitats. Un “buffer” s'encarrega desubministrar les caixes d'una en una que, un cop acabat el circuit, tornen al lloc d'on hansortit. Per donar un producte per bo, es realitzen tests de diverses hores i se n'obté unaestadística de lectures bones/dolentes. Si la ràtio és la desitjada es dóna per bo elproducte.Per aconseguir un disseny correcte s'ha utilitzat diferents eines CAD per dimensionar elsistema de transportadors i els seus elements. Tota l'aplicació està realitzada en 3Dmitjançant el software AutoCAD 3D. L'abast d'aquest projecte inclourà la solució mecànica i pneumàtica del sistema, aixícom el seu muntatge i tot el referent a les normes de seguretat per tal que el sistemacompleixi la normativa referida a la seguretat de màquines

RFID a les biblioteques.

Breu descripció del funcionament d"un sistema RFID, de les seves aplicacions en biblioteques, i dels problemes i limitacions que té.

Nanocharacterization of Soft Biological Samples in Shear Mode with Quartz Tuning Fork Probes

Quartz tuning forks are extremely good resonators and their use is growing in scanning probe microscopy. Nevertheless, only a few studies on soft biological samples have been reported using these probes. In this work, we present the methodology to develop and use these nanosensors to properly work with biological samples. The working principles, fabrication and experimental setup are presented. The results in the nanocharacterization of different samples in different ambients are presented by using different working modes: amplitude modulation with and without the use of a Phase-Locked Loop (PLL) and frequency modulation. Pseudomonas aeruginosa bacteria are imaged in nitrogen using amplitude modulation. Microcontact printed antibodies are imaged in buffer using amplitude modulation with a PLL. Finally, metastatic cells are imaged in air using frequency modulation.

The Electronic Structure of Co-Sputtered Zinc Indium Tin Oxide Thin Films

Zinc indium tin oxide (ZITO) transparent conductive oxide layers were deposited via radio frequency (RF) magnetron co-sputtering at room temperature. A series of samples with gradually varying zinc content was investigated. The samples were characterized with x-ray and ultraviolet photoemission spectroscopy (XPS, UPS) to determine the electronic structure of the surface. Valence and conduction bands maxima (VBM, CBM), and work function were determined. The experiments indicate that increasing Zn content results in films with a higher defect rate at the surface leading to the formation of a degenerately doped surface layer if the Zn content surpasses 50%. Furthermore, the experiments demonstrate that ZITO is susceptible to ultraviolet light induced work function reduction, similar to what was earlier observed on ITO and TiO2 films.

Sistemes logístics de codificació i identificació, i perspectives de futur

Comptar amb sistemes sofisticats de gestió o programes ERP (Enterprise Resource Planning) no és suficient per a les organitzacions. Per a què aquests recursos donin resultats adequats i actualitzats, la informació d’entrada ha de llegir-se de forma automàtica, per aconseguir estalviar en recursos, eliminació d’errors i assegurar el compliment de la qualitat. Per aquest motiu és important comptar amb eines i serveis d’identificació automàtica i col•lecció de dades. Els principals objectius a assolir (a partir de la introducció al lector de la importància dels sistemes logístics d’identificació en un entorn global d’alta competitivitat), són conèixer i comprendre el funcionament de les tres principals tecnologies existents al mercat (codis de barres lineals, codis de barres bidimensionals i sistemes RFID), veure en quin estat d’implantació es troba cadascuna i les seves principals aplicacions. Un cop realitzat aquest primer estudi es pretén comparar les tres tecnologies per o poder obtenir perspectives de futur en l’àmbit de l’autoidentificació. A partir de la situació actual i de les necessitats de les empreses, juntament amb el meravellós món que sembla obrir la tecnologia RFID (Radio Frequency Identification), la principal conclusió a la que s’arribarà és que malgrat les limitacions tècniques dels codis de barres lineals, aquests es troben completament integrats a tota la cadena logística gràcies a l’estandarització i la utilització d’un llenguatge comú, sota el nom de simbologies GTIN (Global Trade Item Number), durant tota la cadena de subministres que garanteixen total traçabilitat dels productes gràcies en part a la gestió de les bases de dades i del flux d’informació. La tecnologia RFUD amb l’EPC (Electronic Product Code) supera aquestes limitacions, convertint-se en el màxim candidat per a substituir els limitats codis de barres. Tot i això, RFID, amb l’EPC, no serà un adequat identificador logístic fins que es superin importants barreres, com són la falta d’estandarització i l’elevat cost d’implantació.

Exploring the high frequency emission of radio loud X-ray binaries

We report millimetre-wave continuum observations of the X-ray binaries Cygnus X-3, SS 433, LSI+61 303, Cygnus X-1 and GRS 1915+105. The observations were carried out with the IRAM 30 m-antenna at 250 GHz (1.25 mm) from 1998 March 14 to March 20. These millimetre measurements are complemented with centimetre observations from the Ryle Telescope, at 15 GHz (2.0 cm) and from the Green Bank Interferometer at 2.25 and 8.3 GHz (13 and 3.6 cm). Both Cygnus X-3 and SS 433 underwent moderate flaring events during our observations, whose main spectral evolution properties are described and interpreted. A significant spectral steepening was observed in both sources during the flare decay, that is likely to be caused by adiabatic expansion, inverse Compton and synchrotron losses. Finally, we also report 250 GHz upper limits for three additional undetected X-ray binary stars: LSI+65 010, LSI+61 235 and X Per.

Design of Novel Frequency Generation Circuit with Application to Ultra-Wideband Distributed Oscillators

Given the urgence of a new paradigm in wireless digital trasmission which should allow for higher bit rate, lower latency and tigher delay constaints, it has been proposed to investigate the fundamental building blocks that at the circuital/device level, will boost the change towards a more efficient network architecture, with high capacity, higher bandwidth and a more satisfactory end user experience. At the core of each transciever, there are inherently analog devices capable of providing the carrier signal, the oscillators. It is strongly believed that many limitations in today's communication protocols, could be relieved by permitting high carrier frequency radio transmission, and having some degree of reconfigurability. This led us to studying distributed oscillator architectures which work in the microwave range and possess wideband tuning capability. As microvave oscillators are essentially nonlinear devices, a full nonlinear analyis, synthesis, and optimization had to be considered for their implementation. Consequently, all the most used nonlinear numerical techniques in commercial EDA software had been reviewed. An application of all the aforementioned techniques has been shown, considering a systems of three coupled oscillator ("triple push" oscillator) in which the stability of the various oscillating modes has been studied. Provided that a certain phase distribution is maintained among the oscillating elements, this topology permits a rise in the output power of the third harmonic; nevertheless due to circuit simmetry, "unwanted" oscillating modes coexist with the intenteded one. Starting with the necessary background on distributed amplification and distributed oscillator theory, the design of a four stage reverse mode distributed voltage controlled oscillator (DVCO) using lumped elments has been presented. All the design steps have been reported and for the first time a method for an optimized design with reduced variations in the output power has been presented. Ongoing work is devoted to model a wideband DVCO and to implement a frequency divider.

Medium access control messaging scheme for cognitive radio networks

Los sistemas de radio cognitivos son una solución a la deficiente distribución del espectro inalámbrico de frecuencias. Usando acceso dinámico al medio, los usuarios secundarios pueden comunicarse en canales de frecuencia disponibles, mientras los usuarios asignados no están usando dichos canales. Un buen sistema de mensajería de control es necesario para que los usuarios secundarios no interfieran con los usuarios primarios en las redes de radio cognitivas. Para redes en donde los usuarios son heterogéneos en frecuencia, es decir, no poseen los mismos canales de frecuencia para comunicarse, el grupo de canales utilizado para transmitir información de control debe elegirse cuidadosamente. Por esta razón, en esta tesis se estudian las ideas básicas de los esquemas de mensajería de control usados en las redes de radio cognitivas y se presenta un esquema adecuado para un control adecuado para usuarios heterogéneos en canales de frecuencia. Para ello, primero se presenta una nueva taxonomía para clasificar las estrategias de mensajería de control, identificando las principales características que debe cumplir un esquema de control para sistemas heterogéneos en frecuencia. Luego, se revisan diversas técnicas matemáticas para escoger el mínimo número de canales por los cuales se transmite la información de control. Después, se introduce un modelo de un esquema de mensajería de control que use el mínimo número de canales y que utilice las características de los sistemas heterogéneos en frecuencia. Por último, se comparan diversos esquemas de mensajería de control en términos de la eficiencia de transmisión.

A simulation-based algorithm for solving the resource-assignment problem in satellite telecommunication networks

This paper proposes an heuristic for the scheduling of capacity requests and the periodic assignment of radio resources in geostationary (GEO) satellite networks with star topology, using the Demand Assigned Multiple Access (DAMA) protocol in the link layer, and Multi-Frequency Time Division Multiple Access (MF-TDMA) and Adaptive Coding and Modulation (ACM) in the physical layer.

The neuronal basis of attention: rate versus synchronization modulation

Extensive theoretical and experimental work on the neuronal correlates of visual attention raises two hypotheses about the underlying mechanisms. The first hypothesis, named biased competition, originates from experimental single-cell recordings that have shown that attention upmodulates the firing rates of the neurons encoding the attended features and downregulates the firing rates of the neurons encoding the unattended features. Furthermore, attentional modulation of firing rates increases along the visual pathway. The other, newer hypothesis assigns synchronization a crucial role in the attentional process. It stems from experiments that have shown that attention modulates gamma-frequency synchronization. In this paper, we study the coexistence of the two phenomena using a theoretical framework. We find that the two effects can vary independently of each other and across layers. Therefore, the two phenomena are not concomitant. However, we show that there is an advantage in the processing of information if rate modulation is accompanied by gamma modulation, namely that reaction times are shorter, implying behavioral relevance for gamma synchronization.

Frequency dynamics of gain-switched injection-locked semiconductor lasers

The frequency dynamics of gain-switched singlemode semiconductor lasers subject to optical injection is investigated. The requirements for low time jitter and reduced frequency chirp operation are studied as a function of the frequency mismatch between the master and slave lasers. Suppression of the power overshoot, typical during gain-switched operation, can be achieved for selected frequency detunings.