General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.

Via-configurable transistor array: a regular design technique to improve ICs yield

Process variations are a major bottleneck for digital CMOS integrated circuits manufacturability and yield. That iswhy regular techniques with different degrees of regularity are emerging as possible solutions. Our proposal is a new regular layout design technique called Via-Configurable Transistors Array (VCTA) that pushes to the limit circuit layout regularity for devices and interconnects in order to maximize regularity benefits. VCTA is predicted to perform worse than the Standard Cell approach designs for a certain technology node but it will allow the use of a future technology on an earlier time. Ourobjective is to optimize VCTA for it to be comparable to the Standard Cell design in an older technology. Simulations for the first unoptimized version of our VCTA of delay and energy consumption for a Full Adder circuit in the 90 nm technology node are presented and also the extrapolation for Carry-RippleAdders from 4 bits to 64 bits.

The marmora used in the imperial cult area of Tarraco (Hispania Citerior)

The imperial cult area of Tarraco was built in the 1st century AD in the highest part of the city and presided over the seat of the Concilium Prouinciae Hispaniae Citerioris. It was a temenos with a similar layout to that of the Forum Pacis and architectural decoration imitating that of the Forum Augustum in Rome, where the use of marble was a fundamental part of the architectural and sculptural decorative programme. An extensive assemblage of marble was recovered during the excavations carried out under the Tarragona Cathedral Master Plan. It reflects the use of imperial quarries in the decorative programme and has been analyzed at the Unitat d’Estudis Arqueomètrics (ICAC) facilities. This assemblage reflects the wide panorama of marmora imported and used in the decoration of the temenos. Local varieties of marmora have been identified in Tarraco, plus a series of foreign marmora from quarries all over the Roman Empire (Greece, Turkey, Egypt and North Africa). All this shows the involvement of the imperial power in the monumental architecture of the capital of the prouincia Hispania Citerior.

A programming environment having three levels of complexity for mobile robotics = Entorno de programación con tres niveles de complejidad para robótica móvil

This paper presents a programming environment for supporting learning in STEM, particularly mobile robotic learning. It was designed to maintain progressive learning for people with and without previous knowledge of programming and/or robotics. The environment was multi platform and built with open source tools. Perception, mobility, communication, navigation and collaborative behaviour functionalities can be programmed for different mobile robots. A learner is able to programme robots using different programming languages and editor interfaces: graphic programming interface (basic level), XML-based meta language (intermediate level) or ANSI C language (advanced level). The environment supports programme translation transparently into different languages for learners or explicitly on learners’ demand. Learners can access proposed challenges and learning interfaces by examples. The environment was designed to allow characteristics such as extensibility, adaptive interfaces, persistence and low software/hardware coupling. Functionality tests were performed to prove programming environment specifications. UV BOT mobile robots were used in these tests

The Application of 3D Reconstruction Techniques in the Analysis of Ancient Tarraco’s Urban Topography

The widespread implementation of GIS-based 3D topographical models has been a great aid in the development and testing of archaeological hypotheses. In this paper, a topographical reconstruction of the ancient city of Tarraco, the Roman capital of the Tarraconensis province, is presented. This model is based on topographical data obtained through archaeological excavations, old photographic documentation, georeferenced archive maps depicting the pre-modern city topography, modern detailed topographical maps and differential GPS measurements. The addition of the Roman urban architectural features to the model offers the possibility to test hypotheses concerning the ideological background manifested in the city shape. This is accomplished mainly through the use of 3D views from the main city accesses. These techniques ultimately demonstrate the ‘theatre-shaped’ layout of the city (to quote Vitrubius) as well as its southwest oriented architecture, whose monumental character was conceived to present a striking aspect to visitors, particularly those arriving from the sea.

Effects of P300-based BCI use on reported presence in a virtual environment

Brain-computer interfaces (BCIs) are becoming more and more popular as an input device for virtual worlds and computer games. Depending on their function, a major drawback is the mental workload associated with their use and there is significant effort and training required to effectively control them. In this paper, we present two studies assessing how mental workload of a P300-based BCI affects participants" reported sense of presence in a virtual environment (VE). In the first study, we employ a BCI exploiting the P300 event-related potential (ERP) that allows control of over 200 items in a virtual apartment. In the second study, the BCI is replaced by a gaze-based selection method coupled with wand navigation. In both studies, overall performance is measured and individual presence scores are assessed by means of a short questionnaire. The results suggest that there is no immediate benefit for visualizing events in the VE triggered by the BCI and that no learning about the layout of the virtual space takes place. In order to alleviate this, we propose that future P300-based BCIs in VR are set up so as require users to make some inference about the virtual space so that they become aware of it,which is likely to lead to higher reported presence.

Modeling and manufacturability assessment of bistable quantum-dot cells

We have investigated the behavior of bistable cells made up of four quantum dots and occupied by two electrons, in the presence of realistic confinement potentials produced by depletion gates on top of a GaAs/AlGaAs heterostructure. Such a cell represents the basic building block for logic architectures based on the concept of quantum cellular automata (QCA) and of ground state computation, which have been proposed as an alternative to traditional transistor-based logic circuits. We have focused on the robustness of the operation of such cells with respect to asymmetries derived from fabrication tolerances. We have developed a two-dimensional model for the calculation of the electron density in a driven cell in response to the polarization state of a driver cell. Our method is based on the one-shot configuration-interaction technique, adapted from molecular chemistry. From the results of our simulations, we conclude that an implementation of QCA logic based on simple ¿hole arrays¿ is not feasible, because of the extreme sensitivity to fabrication tolerances. As an alternative, we propose cells defined by multiple gates, where geometrical asymmetries can be compensated for by adjusting the bias voltages. Even though not immediately applicable to the implementation of logic gates and not suitable for large scale integration, the proposed cell layout should allow an experimental demonstration of a chain of QCA cells.

The octagon, the hendecagon and the approximation of pi: the geometric design of the clypeus in the enclosure of Imperial cult in Tarraco

The ancient temple dedicated to the Roman Emperor Augustus on the hilltop of Tarraco (today’s Tarragona), was the main element of the sacred precinct of the Imperial cult. It was a two hectare square, bordered by a portico with an attic decorated with a sequence of clypeus (i.e. monumental shields) made with marble plates from the Luni-Carrara’s quarries. This contribution presents the results of the analysis of a three-dimensional photogrammetric survey of one of these clipeus, partially restored and exhibited at the National Archaeological Museum of Tarragona. The perimeter ring was bounded by a sequence of meanders inscribed in a polygon of 11 sides, a hendecagon. Moreover, a closer geometric analysis suggests that the relationship between the outer meander rim and the oval pearl ring that delimited the divinity of Jupiter Ammon can be accurately determined by the diagonals of an octagon inscribed in the perimeter of the clypeus. This double evidence suggests a combined layout, in the same design, of an octagon and a hendecagon. Hypothetically, this could be achieved by combining the octagon with the approximation to Pi used in antiquity: 22/7 of the circle’s diameter. This method allows the drawing of a hendecagon with a clearly higher precision than with other ancient methods. Even the modelling of the motifs that separate the different decorative stripes corroborates the geometric scheme that we propose.

Equivalent representation form of oscillators with elastic and damping nonlinear terms

In this work we consider the nonlinear equivalent representation form of oscillators that exhibit nonlinearities in both the elastic and the damping terms. The nonlinear damping effects are considered to be described by fractional power velocity terms which provide better predictions of the dissipative effects observed in some physical systems. It is shown that their effects on the system dynamics response are equivalent to a shift in the coefficient of the linear damping term of a Duffing oscillator. Then, its numerical integration predictions, based on its equivalent representation form given by the well-known forced, damped Duffing equation, are compared to the numerical integration values of its original equations of motion. The applicability of the proposed procedure is evaluated by studying the dynamics response of four nonlinear oscillators that arise in some engineering applications such as nanoresonators, microresonators, human wrist movements, structural engineering design, and chain dynamics of polymeric materials at high extensibility, among others

Consultoria del procés de logística interna del laboratori d'anàlisis clíniques a l'Hospital General de Vic

Com a resultat de les politiques i estratègies de col·laboració entre la universitat de Vic i de l’hospital i de la voluntat de realitzar activitats formatives conjuntes , s’estableix un línia de treball orientada a l’estudi i anàlisi de la situació logística interna actual del laboratori d’anàlisis clíniques de l’Hospital General de Vic. El treball es centra en el procés intern del laboratori i l’abast de l’estudi es troba limitat a les àrees especifiques d’hematologia i coagulació i bioquí… [+]mica. D’aquestes dues àrees el treball realitza un estudi exhaustiu del seu procés intern, identifica les seves activitats i la seva metodologia de treball amb l’objectiu d’elaborar el Value Stream Map de cadascuna de les àrees. Les àrees de Microbiologia, Banc de Sang i Urgències resten fora d’aquest estudi exhaustiu tot i que són presents en el treball per la inevitable interacció que tenen en la globalitat del procés. El treball es centra bàsicament en els processos automatitzats tot i que els processos que es duen a terme en el laboratori són tant automatitzats com manuals. També es limita al sistema productiu intern del laboratori tot i la interacció que té aquest sistema intern amb altres centres productius del sistema com ara són els centres d’atenció primària, els diversos hospitals i centres d’atenció sociosanitària. El laboratori es troba immers en el moment de l’elaboració d’aquest treball en un situació de canvi i millora del seus processos interns que consisteixen principalment en la substitució de part la maquinària actual que obliguen a la definició d’un nou layout i d’una nova distribució de la producció a cada màquina. A nivell extern també s’estan produint millores en el sistema informàtic de gestió que afecten a part del seu procés. L’objectiu del treball és donar visibilitat total al procés de logística interna actual del laboratori, identificant clarament com són i quina seqüència tenen els processos logístics interns i els mètodes de treball actuals, tant de recursos màquina com recursos persona, per poder identificar sota una perspectiva de generació de valor, aquells punts concrets de la logística interna que poden ser millorats en quant a eficiència i productivitat amb l’objectiu que un cop identificats es puguin emprendre accions i/o projectes de millora. El treball finalitza amb un anàlisis final del procés logística interna des d’una òptica Lean. Per fer-ho, identifica aquelles activitats que no aporten valor al procés o MUDA i les classifica en set categories i es realitzen diverses propostes de millora com són la implantació d’un flux continu , anivellat i basat en un concepte pull , identifica activitats que poden ser estandarditzades i/o simplificades i proposa modificacions en les infraestructures físiques per donar major visibilitat al procés. L’aspecte humà del procés es planteja des d’un punt de vist de metodologia, formació, comunicació i aplicació de les 5S.

Programa d'anàlisi d'imatges de provetes metal·logràfiques

L’objectiu del present TFM és explorar les possibilitats del programa matemàtic MATLAB i la seva eina Entorn de Disseny d’Interfícies Gràfiques d’Usuari (GUIDE), desenvolupant un programa d’anàlisi d’imatges de provetes metal·logràfiques que es pugui utilitzar per a realitzar pràctiques de laboratori de l’assignatura Tecnologia de Materials de la titulació de Grau en Enginyeria Mecatrònica que s’imparteix a la Universitat de Vic. Les àrees d’interès del treball són la Instrumentació Virtual, la programació MATLAB i les tècniques d’anàlisi d’imatges metal·logràfiques. En la memòria es posa un èmfasi especial en el disseny de la interfície i dels procediments per a efectuar les mesures. El resultat final és un programa que satisfà tots els requeriments que s’havien imposat en la proposta inicial. La interfície del programa és clara i neta, destinant molt espai a la imatge que s’analitza. L’estructura i disposició dels menús i dels comandaments ajuda a que la utilització del programa sigui fàcil i intuïtiva. El programa s’ha estructurat de manera que sigui fàcilment ampliable amb altres rutines de mesura, o amb l’automatització de les rutines existents. Al tractar-se d’un programa que funciona com un instrument de mesura, es dedica un capítol sencer de la memòria a mostrar el procediment de càlcul dels errors que s’ocasionen durant la seva utilització, amb la finalitat de conèixer el seu ordre de magnitud, i de saber-los calcular de nou en cas que variïn les condicions d’utilització. Pel que fa referència a la programació, malgrat que MATLAB no sigui un entorn de programació clàssic, sí que incorpora eines que permeten fer aplicacions no massa complexes, i orientades bàsicament a gràfics o a imatges. L’eina GUIDE simplifica la realització de la interfície d’usuari, malgrat que presenta problemes per tractar dissenys una mica complexos. Per altra banda, el codi generat per GUIDE no és accessible, cosa que no permet modificar manualment la interfície en aquells casos en els que GUIDE té problemes. Malgrat aquests petits problemes, la potència de càlcul de MATLAB compensa sobradament aquestes deficiències.

Periodismo y dispositivos móviles de lecto-escritura. Introducción al diseño de contenidos para tabletas

El lanzamiento de las tabletas, especialmente la iPad de Apple en 2010, abrió la competencia entre las compañías de comunicación en el sentido de hacer disponible el contenido para este entorno de medios emergentes. La fuga de lectores de periódicos impresos y la consecuente caída en las ganancias por publicidad, forzó a las compañías periodísticas a que buscaran los otros medios de mantener sus negocios. La diversificación de productos y la penetración de los periódicos en dispositivos móviles constituyen un escenario prometedor para el medio. El vertiginoso volumen de ventas de las tabletas indica que en 2012 serán comercializadas más de 140 millones de unidades en el mundo. El diseño de los periódicos en tabletas está íntimamente ligado al diseño de la versión impresa por la fuerza de su metáfora. El desafío es encontrar un diseño de páginas propio, aprovechando el potencial multimedia sin interferir negativamente en la legibilidad y en el carácter intrínseco de informar.