Influence of premetallization surface treatment on the formation of Schottky Au-nGaN contacts

The influence of premetallization surface preparation on the structural, chemical, and electrical properties of Au-nGaN interfaces has been investigated by x-ray photoemission spectroscopy (XPS), current-voltage measurement (I-V) and cross-section transmission electron microscopy (TEM). XPS analysis showed that the three GaN substrate treatments investigated i.e., ex situ hydrofluoric acid etch, in situ anneal in ultrahigh-vacuum (UHV), and in situ Ga reflux cleaning in UHV result in surfaces increasingly free of oxygen contamination. XPS and TEM characterization of Au-nGaN formed after the three premetallization surface treatments show that HF etching and UHV annealing produce abrupt, well-defined interfaces. Conversely, GaN substrate cleaning in a Ga flux results in Au/GaN intermixing. I-V characterization of Au¿nGaN contacts yields a Schottky barrier height of 1.25 eV with a very low-ideality factor and very good contact uniformity for the premetallization UHV anneal, while the Ga reflux cleaning results in a much lower barrier (0.85 eV), with poor ideality and uniformity. I-V and XPS results suggest a high density of acceptor states at the surface, which is further enhanced by UHV annealing. These results are discussed in the context of current models of Schottky barrier formation.

Time-dependent couplings and crossover length scales in nonequilibrium surface roughening

We show that time-dependent couplings may lead to nontrivial scaling properties of the surface fluctuations of the asymptotic regime in nonequilibrium kinetic roughening models. Three typical situations are studied. In the case of a crossover between two different rough regimes, the time-dependent coupling may result in anomalous scaling for scales above the crossover length. In a different setting, for a crossover from a rough to either a flat or damping regime, the time-dependent crossover length may conspire to produce a rough surface, although the most relevant term tends to flatten the surface. In addition, our analysis sheds light into an existing debate in the problem of spontaneous imbibition, where time-dependent couplings naturally arise in theoretical models and experiments.

Origin of the neutron skin thickness of 208Pb in nuclear mean-field models

We study whether the neutron skin thickness Δrnp of 208Pb originates from the bulk or from the surface of the nucleon density distributions, according to the mean-field models of nuclear structure, and find that it depends on the stiffness of the nuclear symmetry energy. The bulk contribution to Δrnp arises from an extended sharp radius of neutrons, whereas the surface contribution arises from different widths of the neutron and proton surfaces. Nuclear models where the symmetry energy is stiff, as typical of relativistic models, predict a bulk contribution in Δrnp of 208Pb about twice as large as the surface contribution. In contrast, models with a soft symmetry energy like common nonrelativistic models predict that Δrnp of 208Pb is divided similarly into bulk and surface parts. Indeed, if the symmetry energy is supersoft, the surface contribution becomes dominant. We note that the linear correlation of Δrnp of 208Pb with the density derivative of the nuclear symmetry energy arises from the bulk part of Δrnp. We also note that most models predict a mixed-type (between halo and skin) neutron distribution for 208Pb. Although the halo-type limit is actually found in the models with a supersoft symmetry energy, the skin-type limit is not supported by any mean-field model. Finally, we compute parity-violating electron scattering in the conditions of the 208Pb parity radius experiment (PREX) and obtain a pocket formula for the parity-violating asymmetry in terms of the parameters that characterize the shape of the 208Pb nucleon densities.

Using spatially distributed parameters and multi-response objective functions to solve parameterization of complex applications of semi-distributed hydrological models

Application of semi-distributed hydrological models to large, heterogeneous watersheds deals with several problems. On one hand, the spatial and temporal variability in catchment features should be adequately represented in the model parameterization, while maintaining the model complexity in an acceptable level to take advantage of state-of-the-art calibration techniques. On the other hand, model complexity enhances uncertainty in adjusted model parameter values, therefore increasing uncertainty in the water routing across the watershed. This is critical for water quality applications, where not only streamflow, but also a reliable estimation of the surface versus subsurface contributions to the runoff is needed. In this study, we show how a regularized inversion procedure combined with a multiobjective function calibration strategy successfully solves the parameterization of a complex application of a water quality-oriented hydrological model. The final value of several optimized parameters showed significant and consistentdifferences across geological and landscape features. Although the number of optimized parameters was significantly increased by the spatial and temporal discretization of adjustable parameters, the uncertainty in water routing results remained at reasonable values. In addition, a stepwise numerical analysis showed that the effects on calibration performance due to inclusion of different data types in the objective function could be inextricably linked. Thus caution should be taken when adding or removing data from an aggregated objective function.

Depositional models of lacustrine evaporites in the SE margin of the Ebro basin (Paleogene, NE Spain)

An important evaporitic sedimentation occurred during the Paleogene (Eocene to lower Oligocene) in the Barberà sector of the southeastern margin of the Tertiary Ebro Basin. This sedimentation took place in shallow lacustrine environments and was controlled by a number of factors: 1) the tectonic structuration of the margin; 2) the high calcium sulphate content in the meteoric waters coming from the marginal reliefs; 3) the semiarid climate; and 4) the development of large alluvial fans along the basin margin, which also conditioned the location of the saline lakes. The evaporites are currently composed of secondary gypsum in surface and anhydrite at depth. There are, however, vestiges of the local presence of sodium sulphates. The evaporite units, with individual thicknesses ranging between 50 and 100 m, are intercalated within various lithostratigraphic formations and exhibit a paleogeographical pattern. The units located closer to the basin margin are characterized by a massive gypsum lithofacies (originally, bioturbated gypsum) bearing chert, and also by meganodular gypsum locally (originally, meganodules of anhydrite) in association with red lutites and clastic intercalations (gypsarenites, sandstones and conglomerates). Chert, which is only linked to the thickest gypsum layers, seems to be an early diagenetic, lacustrine product. Cyclicity in these proximal units indicates the progressive development of lowsalinity, lacustrine bodies on red mud flats. At the top of some cycles, exposure episodes commonly resulted in dissolution, erosion, and the formation of edaphic features. In contrast, the units located in a more distal position with regard to the basin margin are formed by an alternation of banded-nodular gypsum and laminated gypsum layers in association with grey lutites and few clastic intercalations. These distal units formed in saline lakes with a higher ionic concentration. Exposure episodes in these lakes resulted in the formation of synsedimentary anhydrite and sabkha cycles. In some of these units, however, outer rims characterized by a lithofacies association similar to that of the proximal units occur (nodular gypsum, massive gypsum and chert nodules).

Turistes mobiltzats : el turisme cultural a la societat digital mòbil

L’impacte de la societat en xarxa en el turisme està transformant els models de negoci pel canvi en el flux i en les dinàmiques d’accés a la informació. La irrupció dels mitjans socials i la revolució mòbil canvien la manera de planificar, experimentar i compartir el viatge. Si fa uns anys es parlava de la revolució d’Internet, avui podem dir que estem assistint a la Revolució Mòbil. No es tracta d’una evolució de la primera, sinó d’un fet que té les seves pròpies característiques, els seus protagonistes i la seva implicació en la indústria del turisme i la cultura. El gadget de referència en l’impuls de la Internet social està sent el mòbil, un sensor d’ubiqüitat i polièdric. L’accés a la informació, el consum de continguts i la compra de serveis ja no es limita a una actitud relaxada davant una pantalla, sinó que es produeix al llarg de tot el dia i en qualsevol lloc. Això fa que la mobilitat afecti tot el cicle del viatge, és a dir, l’abans, el durant i el després

Surface-enhanced laser desorption/ionisation time-of-flight mass spectrometry: A tool to predict pork quality

Expression of water soluble proteins of fresh pork Longissimus thoracis from 4 pure breed pigs (Duroc, Large White, Landrace, and Piétrain) was studied to identify candidate protein markers for meat quality. Surface-enhanced laser desorption/ionisation time-of-flight mass spectrometry (SELDI-TOF-MS) was used to obtain the soluble protein profiles of Longissimus thoracis muscles. The pure breeds showed differences among the studied meat quality traits (pHu, drip loss, androstenone, marbling, intramuscular fat, texture, and moisture), but no significant differences were detected in sensory analysis. Associations between protein peaks obtained with SELDI-TOF-MS and meat quality traits, mainly water holding capacity, texture and skatole were observed. Of these peaks, a total of 10 peaks from CM10 array and 6 peaks from Q10 array were candidate soluble protein markers for pork loin quality. The developed models explained a limited proportion of the variability, however they point out interesting relationships between protein expression and meat quality

A model of the wind direction signature in the Stokes emission vector from the ocean surface at microwave frequencies

This paper presents a model of the Stokes emission vector from the ocean surface. The ocean surface is described as an ensemble of facets with Cox and Munk's (1954) Gram-Charlier slope distribution. The study discusses the impact of different up-wind and cross-wind rms slopes, skewness, peakedness, foam cover models and atmospheric effects on the azimuthal variation of the Stokes vector, as well as the limitations of the model. Simulation results compare favorably, both in mean value and azimuthal dependence, with SSM/I data at 53° incidence angle and with JPL's WINDRAD measurements at incidence angles from 30° to 65°, and at wind speeds from 2.5 to 11 m/s.

Empirical models for predicting the production of wild mushrooms in Scots pine (Pinus sylvestris L.) forests in the Central Pyrenees

Mushroom picking has become a widespread autumn recreational activity in the Central Pyrenees and other regions of Spain. Predictive models that relate mushroom production or fungal species richness with forest stand and site characteristics are not available. This study used mushroom production data from 24 Scots pine plots over 3 years to develop a predictive model that could facilitate forest management decisions when comparing silvicultural options in terms of mushroom production. Mixed modelling was used to model the dependence of mushroom production on stand and site factors. The results showed that productions were greatest when stand basal area was approximately 20 m2 ha-1. Increasing elevation and northern aspect increased total mushroom production as well as the production of edible and marketed mushrooms. Increasing slope decreased productions. Marketed Lactarius spp., the most important group collected in the region, showed similar relationships. The annual variation in mushroom production correlated with autumn rainfall. Mushroom species richness was highest when the total production was highest.

A web ontologies framework for digital rights management

In order to improve the management of copyright in the Internet, known as Digital Rights Management, there is the need for a shared language for copyright representation. Current approaches are based on purely syntactic solutions, i.e. a grammar that defines a rights expression language. These languages are difficult to put into practise due to the lack of explicit semantics that facilitate its implementation. Moreover, they are simple from the legal point of view because they are intended just to model the usage licenses granted by content providers to end-users. Thus, they ignore the copyright framework that lies behind and the whole value chain from creators to end-users. Our proposal is to use a semantic approach based on semantic web ontologies. We detail the development of a copyright ontology in order to put this approach into practice. It models the copyright core concepts for creation, rights and the basic kinds of actions that operate on content. Altogether, it allows building a copyright framework for the complete value chain. The set of actions operating on content are our smaller building blocks in order to cope with the complexity of copyright value chains and statements and, at the same time, guarantee a high level of interoperability and evolvability. The resulting copyright modelling framework is flexible and complete enough to model many copyright scenarios, not just those related to the economic exploitation of content. The ontology also includes moral rights, so it is possible to model this kind of situations as it is shown in the included example model for a withdrawal scenario. Finally, the ontology design and the selection of tools result in a straightforward implementation. Description Logic reasoners are used for license checking and retrieval. Rights are modelled as classes of actions, action patterns are modelled also as classes and the same is done for concrete actions. Then, to check if some right or license grants an action is reduced to check for class subsumption, which is a direct functionality of these reasoners.

Discriminating crop, weeds and soil surface with a terrestrial LIDAR sensor

In this study, the evaluation of the accuracy and performance of a light detection and ranging (LIDAR) sensor for vegetation using distance and reflection measurements aiming to detect and discriminate maize plants and weeds from soil surface was done. The study continues a previous work carried out in a maize field in Spain with a LIDAR sensor using exclusively one index, the height profile. The current system uses a combination of the two mentioned indexes. The experiment was carried out in a maize field at growth stage 12–14, at 16 different locations selected to represent the widest possible density of three weeds: Echinochloa crus-galli (L.) P.Beauv., Lamium purpureum L., Galium aparine L.and Veronica persica Poir.. A terrestrial LIDAR sensor was mounted on a tripod pointing to the inter-row area, with its horizontal axis and the field of view pointing vertically downwards to the ground, scanning a vertical plane with the potential presence of vegetation. Immediately after the LIDAR data acquisition (distances and reflection measurements), actual heights of plants were estimated using an appropriate methodology. For that purpose, digital images were taken of each sampled area. Data showed a high correlation between LIDAR measured height and actual plant heights (R2 = 0.75). Binary logistic regression between weed presence/absence and the sensor readings (LIDAR height and reflection values) was used to validate the accuracy of the sensor. This permitted the discrimination of vegetation from the ground with an accuracy of up to 95%. In addition, a Canonical Discrimination Analysis (CDA) was able to discriminate mostly between soil and vegetation and, to a far lesser extent, between crop and weeds. The studied methodology arises as a good system for weed detection, which in combination with other principles, such as vision-based technologies, could improve the efficiency and accuracy of herbicide spraying.

Nuclear surface properties in relativistic effective field theory

We perform Hartree calculations of symmetric and asymmetric semi-infinite nuclear matter in the framework of relativistic models based on effective hadronic field theories as recently proposed in the literature. In addition to the conventional cubic and quartic scalar self-interactions, the extended models incorporate a quartic vector self-interaction, scalar-vector non-linearities and tensor couplings of the vector mesons. We investigate the implications of these terms on nuclear surface properties such as the surface energy coefficient, surface thickness, surface stiffness coefficient, neutron skin thickness and the spin-orbit force.

Molecular dynamics simulation of the spherical electrical double layer of a soft nanoparticle. Effect of the surface and counterion valence

Molecular dynamics simulations were performed to study the ion and water distribution around a spherical charged nanoparticle. A soft nanoparticle model was designed using a set of hydrophobic interaction sites distributed in six concentric spherical layers. In order to simulate the effect of charged functionalyzed groups on the nanoparticle surface, a set of charged sites were distributed in the outer layer. Four charged nanoparticle models, from a surface charge value of −0.035 Cm−2 to − 0.28 Cm−2, were studied in NaCl and CaCl2 salt solutions at 1 M and 0.1 M concentrations to evaluate the effect of the surface charge, counterion valence, and concentration of added salt. We obtain that Na + and Ca2 + ions enter inside the soft nanoparticle. Monovalent ions are more accumulated inside the nanoparticle surface, whereas divalent ions are more accumulated just in the plane of the nanoparticle surface sites. The increasing of the the salt concentration has little effect on the internalization of counterions, but significantly reduces the number of water molecules that enter inside the nanoparticle. The manner of distributing the surface charge in the nanoparticle (uniformly over all surface sites or discretely over a limited set of randomly selected sites) considerably affects the distribution of counterions in the proximities of the nanoparticle surface.

Effect of the surface charge discretization on electric double layers. A Monte Carlo simulation study

The structure of the electric double layer in contact with discrete and continuously charged planar surfaces is studied within the framework of the primitive model through Monte Carlo simulations. Three different discretization models are considered together with the case of uniform distribution. The effect of discreteness is analyzed in terms of charge density profiles. For point surface groups,a complete equivalence with the situation of uniformly distributed charge is found if profiles are exclusively analyzed as a function of the distance to the charged surface. However, some differences are observed moving parallel to the surface. Significant discrepancies with approaches that do not account for discreteness are reported if charge sites of finite size placed on the surface are considered.

Ocean surface winds drive dynamics of transoceanic aerial movements

Global wind patterns influence dispersal and migration processes of aerial organisms, propagules and particles, which ultimately could determine the dynamics of colonizations, invasions or spread of pathogens. However, studying how wind-mediated movements actually happen has been hampered so far by the lack of high resolution global wind data as well as the impossibility to track aerial movements. Using concurrent data on winds and actual pathways of a tracked seabird, here we show that oceanic winds define spatiotemporal pathways and barriers for large-scale aerial movements. We obtained wind data from NASA SeaWinds scatterometer to calculate wind cost (impedance) models reflecting the resistance to the aerial movement near the ocean surface. We also tracked the movements of a model organism, the Cory's shearwater (Calonectris diomedea), a pelagic bird known to perform long distance migrations. Cost models revealed that distant areas can be connected through"wind highways" that do not match the shortest great circle routes. Bird routes closely followed the low-cost"wind-highways" linking breeding and wintering areas. In addition, we found that a potential barrier, the near surface westerlies in the Atlantic sector of the Intertropical Convergence Zone (ITCZ), temporally hindered meridional trans-equatorial movements. Once the westerlies vanished, birds crossed the ITCZ to their winter quarters. This study provides a novel approach to investigate wind-mediated movements in oceanic environments and shows that large-scale migration and dispersal processes over the oceans can be largely driven by spatiotemporal wind patterns.