Optimising the design and manufacture of a customised, prescription fit, Maxillo-facial prosthesis

This thesis is a continuation of the Enterprise-Ireland Research Innovation Fund (RIF) Project entitled’ "Design and Manufacturing of Customised Maxillo-Facial Prostheses" The primary objective of this Internal Research Development Program (IRDP) project was to investigate two fundamental design changes 1 To incorporate the over-denture abutments directly into the implant. 2 To remove the restraining wings by the addition of screws, which affix the. implant to the dense material of the jawbone. The prosthetic was redesigned using the ANSYS Finite Element Analysis software program and analysed to* • Reduce the internal von Mises stress distribution The new prosthetic had a -63.63 % lower von Mises stress distribution when compared with the original prosthetic. • Examine the screw preload effects. A maximum relative displacement of 22 6 * lO^mm between the bone and screw was determined, which is well below the critical threshold of micromotion which prevents osseointegration • Investigate the prosthetic-bone contact interface. Three models of the screw, prosthesis, and bone, were studied. (Axisymmetnc, quarter volume, and full volume), a recommended preload torque of 0 32 Nm was applied to the prosthetic and a maximum von Mises stress of 1.988 MPa was predicted • Study the overdenture removal forces. This analysis could not be completed because the correct plastic multilinear properties of the denture material could not be established The redesigned prosthetic was successfully manufactured on a 3-axis milling machine with an indexing system The prosthetic was examined for dimensional quality and strength The research established the feasibility of the new design and associated manufacturing method.

Design of a bifurcated stent graft, with its accompanying delivery system.

Abdominal Aortic Aneurysms (AAA) haemorhaging is a life-threatening disease. An aneurysm is a permanent swelling of an artery due to a weakness in its wall. Current surgical repair involves opening the chest or abdomen, gaining temporary vascular control of the aorta and suturing a prosthetic graft to the healthy aorta within the aneurysm itself The outcome of this surgical approach is not perfect, and the quality of life after this repair is impaired by postoperative pain, sexual dysfunction, and a lengthy hospital stay resulting in high health costs. All these negative effects are related to the large incision and extensive tissue dissection. Endovascular grafting is an alternative to the standard surgical method. This treatment is a less invasive method of treating aortic aneurysms. It involves a surgical exposure of the common femoral arteries where the stent graft can be inserted through by an over-the-wire technique. All manipulations are controlled from a remote place by the use of a catheter and this technique avoids the need to directly expose the diseased artery through a large incision or an extensive dissection. The proposed design method outlined in this project is to develop the endovascular approach. The main aim is to design an unitary bifurcated stent graft (1 e- bifurcated graft as a single component) to treat these Abdominal Aortic Aneurysms. This includes the delivery system and deployment mechanism necessary to first accurately position the stent graft across the aneurysm sac and also across the iliac bifurcation, and secondly fix the stent graft in position by using expandable metal stents. Thus, excluding the aneurysm from the circulation and therefore preventing rupture. Miniaturisation is a critical aspect of this design, as the smaller the crimped stent graft the easier to guide through the vascular system to the desired location. Biocompatibility is an important aspect. The preferred materials for this prosthesis are to use Shape Memory Alloys for the stent and a multifilament fabric for the graft. A taper design is applied for the geometry as this gives a favourable flow characteristic and reduced wave reflections. Adequate testing of the stent graft to prove its durability and the ease of the method of deployment is a prerequisite. A bench test facility has being designed and build to replicate the cardiovascular system and the disease in question aortic aneurysms at the iliac bifurcation. The testing here shows the feasibility of the proposed delivery system and the durability of the stent graft across the aneurysm sac. Finally, these endovascular treatments offer the economic advantage of short hospital stays or even treatment as an outpatient, as well as elimination of the need for postoperative intensive care The risk of developing an aneurysm increases with age, that is one of the mam reasons to look for less invasive ways of treating aneurysms. Consequently, there is enormous pressure to develop and use these devices rapidly.

Ireland’s understudied flatfish: reproduction, age and growth of the dab Limanda limanda (L.) in Irish coastal waters

In Ireland, although flatfish form a valuable fishery, little is known about the smallest, the dab Limanda limanda. In this study, a variety of parameters of reproductive development, including ovarian phase description, gonadosomatic index (GSI), hepatosomatic index (HSI), relative condition (Kn) and oocyte size were analysed to provide information on the dab’s reproductive cycle and spawning periods. Sampling were collected monthly over an 18-month period using bottom trawls of the Irish coastline. A six phase macroscopic guide was developed for both sexes of dab, and verified using histology. In comparisons of macroscopic and microscopic phases, there was high agreement in the proposed female guide (86%), with males demonstratively lower (62%). No significant bias was observed between the the two reproductive methods. When the male macroscopic guide was examined, misclassification was high in phase 5 and phase 5 (41%), with 96% of misclassification occurring in adjacent phases. The sampled population was primarily composed of females, with ratios of females to males 1:0.6, although the predominance of females was less noticeable during the reproductive season. Oocyte growth in dab follows asynchronous development, and spawn over a protracted period indicating a batch spawning strategy. Spawning occurred mainly in early spring, with total regeneration of gonads by May. The length at which 50% of the population was reproductively mature was identified as 14cm and 17cm, for male and female dab, respectively. Precision and bias in age determinations using whole otoliths to age dab was investigated using six age readers from various institutions. Low levels of precision were obtained (CV: 10-23%) inferring the need for an alternative methodology. Precision and bias was influence by the level of experience of the reader, with ageing error attributed to interpretative differences and difficulty in edge determination. Sectioned otolith age determinations were subsequently compared to whole otolith age determinations using two age readers experienced in dab ageing. Although increased precision was observed in whole otoliths from previous estimates (CV=0%, 0% APE), sectioned otoliths were used for growth models. This was based on multinominal logistic regression on age length keys developed using both ageing methods. Biological data (length and age) for both sexes was applied to four growth models, where the Akaike criterion and Multi model Inference indicated the logistic model as having the best fit to the collected data. In general, female dab attained a longer length then males, with growth rates significantly different between the two sexes. Length weight relationships between the two sexes were also significantly different.