An investigation into the temperature distribution resulting from cutting of compact bone using a reciprocating bone saw

Surgical procedures such as osteotomy and hip replacement involve the cutting of bone with the aid of various manual and powered cutting instruments including manual and powered bone saws. The basic mechanics of bone sawing processes are consistent with most other material sawing processes such as for wood or metal. Frictional rubbing between the blade of the saw and the bone results in the generation of localised heating of the cut bone. Research studies have been carried out which consider the design of the bone saw which deals with specifics of the saw teeth geometry and research which examines the effect of drilling operations on heating of the bone has shown that elevated temperatures will occur from frictional overheating. This overheating in localised areas is known to have an impact on the rate of healing of the bone post operation and the sharpness life of the blade. The purpose of this study was to measure the temperature at three zones at fixed intervals of 3mm, 6mm, and 9mm away from the cutting zone. It should be noted that it was the first time that this measurement technique was used to measure the temperature gradient through the bone specimen thereby establishing the extent to which clinicians are experiencing thermal injury during sawing of bone while using a reciprocating saw. The effect of various cutting feed rate on temperature elevation was also investigated in this research. The results showed that there will be a region of bone at least 9mm either side of the cutting blade experiencing thermal injury as temperatures in this region exceeded the threshold temperature of 44°C for necrosis (cell death).

Investigating the long term planning framework for the Galway Bay community from climate change.

This research looked at the scientific evidence available on climate change and in particular, projections on sea level rise which ranged from 0.5m to 2m by the end of the century. These projections were then considered in an Irish context. A review of current policy in Ireland revealed that there was no dedicated Government policy on climate change or coastal zone management. In terms of spatial planning policy, it became apparent that there was little or no guidance on climate change either at a national, regional or local level. Therefore, to determine the likely impacts of sea level rise in Ireland based on current spatial planning practice and policy, a scenario-building exercise was carried out for two case study areas in Galway Bay. The two case study areas were: Oranmore, a densely populated town located to the east of Inner Galway Bay; and Tawin Island, a rural dispersed community, located to the south east of Inner Galway Bay. A ‘best’ and ‘worse’ case scenario was envisaged for both areas in terms of sea level rise. In the absence of specific climate change policies it was projected that in the ‘best’ case scenario of 0.5m sea level rise, Tawin Island would suffer serious and adverse impacts while Oranmore was likely to experience slight to moderate impacts. However, in the ‘worse’ case scenario of a 2m sea level rise, it was likely that Tawin Island would be abandoned while many houses, businesses and infrastructure built within the floodplain of Oranmore Bay would be inundated and permanently flooded. In this regard, it was the author’s opinion that a strategic and integrated climate change policy and adaptation plan is vital for the island of Ireland that recognises the importance of integrated land use and spatial planning in terms of mitigation and adaptation to climate change.

Acoustic emission analysis of the effect of a 2D wedge shaped blade on the compact bone cutting process

Surgeons may use a number of cutting instruments such as osteotomes and chisels to cut bone during an operative procedure. The initial loading of cortical bone during the cutting process results in the formation of microcracks in the vicinity of the cutting zone with main crack propagation to failure occuring with continued loading. When a material cracks, energy is emitted in the form of Acoustic Emission (AE) signals that spread in all directions, therefore, AE transducers can be used to monitor the occurrence and development of microcracking and crack propagation in cortical bone. In this research, number of AE signals (hits) and related parameters including amplitude, duration and absolute energy (abs-energy) were recorded during the indentation cutting process by a wedge blade on cortical bone specimens. The cutting force was also measured to correlate between load-displacement curves and the output from the AE sensor. The results from experiments show AE signals increase substantially during the loading just prior to fracture between 90% and 100% of maximum fracture load. Furthermore, an amplitude threshold value of 64dB (with approximate abs-energy of 1500 aJ) was established to saparate AE signals associated with microcracking (41 – 64dB) from fracture related signals (65 – 98dB). The results also demonstrated that the complete fracture event which had the highest duration value can be distinguished from other growing macrocracks which did not lead to catastrophic fracture. It was observed that the main crack initiation may be detected by capturing a high amplitude signal at a mean load value of 87% of maximum load and unsteady crack propagation may occur just prior to final fracture event at a mean load value of 96% of maximum load. The author concludes that the AE method is useful in understanding the crack initiation and fracture during the indentation cutting process.