Spray coating of oxide and chalcogenide semiconductor layers for TFT application

This work documents the deposition and optimization of semiconductor thin films using chemical spray coating technique (CSC) for application on thin-film transistors (TFTs), with a low-cost, simple method. CSC setup was implemented and explored for industrial application, within Holst Centre, an R&D center in the Netherlands. As zinc oxide had already been studied within the organization, it was used as a standard material in the initial experiments, obtaining typical mobility values of 0.14 cm2/(V.s) for unpatterned TFTs. Then, oxide X layer characteristics were compared for films deposited with CSC at 40°C and spin-coating. The mobility of the spin-coated TFTs was 103 cm2/(V.s) higher, presumably due to the lack of uniformity of spray-coated film at such low temperatures. Lastly, tin sulfide, a relatively unexplored material, was deposited by CSC in order to obtain functional TFTs and explore the device’s potential for working as a phototransistor. Despite the low mobilities of the devices, a sensitive photodetector was made, showing drain current variation of nearly one order of magnitude under yellow light. CSC technique’s simplicity and versatility was confirmed, as three different semiconductors were successfully implemented into functional devices.

Chemical reaction network of flavylium ions in heterogeneous media

Dissertação apresentada para a obtenção do Grau de Doutor em Química, especialidade em Química-Física, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Historically accurate reconstructions and characterisation of chrome yellow pigments

Dissertation presented at the Faculty of Sciences and Technology of the New University of Lisbon in fulfillment of the requirements for the Master degree in Conservation Science

Light controlled synthesis of nucleic acids

Dissertação apresentada para obtenção do grau de Doutor em Bioquímica - especialidade Biotecnologia, pela Universidade Nova de Lisboa,Faculdade de Ciências e Tecnologia

Comparison of different techniques for mouse transgenesis

RESUMO: O uso de ratinhos transgénicos em neurociências aumentou consideravelmente nos últimos anos devido ao crescente interesse em compreender o cérebro e a necessidade de solucionar situações clínicas do foro neurológico e psiquiátrico. Para esse efeito, diferentes métodos de produção de animais transgénicos têm sido testados. O objectivo desta tese foi comparar métodos de integração aleatória de um transgene no genoma de ratinhos em termos de eficiência, estabilidade da integração do transgene, número de animais e de horas de trabalho necessárias para cada método. Assim, foi comparado o método mais utilizado - microinjecção pronuclear (PNMI) - com duas outras técnicas cujo desempenho foi considerado promissor – a transferência génica através dos testículos por electroporação e transfecção por lentivírus in vivo. As três técnicas foram realizadas usando um gene repórter sob o controlo de um promotor constitutivo, e depois reproduzidas usando um gene de interesse de modo a permitir obtenção de um animal capaz de ser usado em experimentação laboratorial. O transgene de interesse utilizado codifica uma proteína de fusão correspondendo a uma variante da rodopsina (channelrhodopsin) fundida à proteína enhanced yellow fluorescente protein ((EYFP) resultando num produto designado ChR2-EYFP. Este animal transgénico apresentaria expressão deste canal iónico apenas em células dopaminergicas, o que, com manipulação optogenética, tornaria possivel a activação especifica deste grupo de neurónios e, simultaneamente, a observação do impacto desta manipulação no comportamento num animal em livre movimento. Estas ferramentas são importantes na investigação básica em neurociências pois ajudam a esclarecer o papel de grupos específicos de neurónios e compreender doenças como a doença de Parkinson ou a esquizofrenia onde a função de certos tipos de neurónios de encontra alterada. Quando comparados os três métodos realizados verifica-se que usando um gene repórter PMNI resulta em 31,3% de, a de animais transgénicos obtidos, a electroporação de testículos em 0% e a injecção de lentivírus em 0%. Quando usado o gene de interesse, os resultados obtidos são, respectivamente, 18,8%, 63,9% e 0%.--------------ABSTRACT: The use of transgenic mice is increasing in all fields of research, particularly in neuroscience, due to the widespread need of animal models to solve neurological and psychiatric medical conditions. Different methodologies have been tested in the last decades in order to produce such transgenic animals. The ultimate goal of this thesis is to compare different methods of random integration of a transgene in the genome of mice in terms of efficiency, stability of the transgene integration, number of animals required and the labour intensity of each technique. We compared the most used method – pronuclear microinjection (PNMI) – with two other promising techniques – Testis Mediated Gene Transfer (TMGT) by electroporation and in vivo lentiviral transfection. The three techniques were performed using a reporter gene – green fluorescent protein (GFP), whose transcription was driven by the constitutive cytomegalovirus (CMV) promoter. These three techniques were later reproduced using the tyrosine hydroxylase promoter (TH) and the neuronal manipulator, channelrhodopsin-2 fused to the enhanced yellow fluorescent reporter protein (ChR2-EYFP). The transgenic animal we sough to produce would express the light driven channel only in dopaminergic cells, making possible to specifically activate this group of neurons, while simultaneously observe the behaviour in a freely moving animal. This is a very important tool in basic neuroscience research since it helps to clarify the role of specific groups of neurons, map circuits in the brain, and consequently understand neurological diseases such as Parkinson’s disease or schizophrenia, where the function of certain types of neurons is affected. When comparing the three methods, it was verified that using a reporter gene PNMI resulted in 31.3% of transgenic mice obtained, testis electroporation in 0% and lentiviral injection in 0%. When using the gene of interest, the results obtained were, respectively, 18.8%, 63.9% and 0%.

Green light for green energy: Growth in spite of crisis

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Finance from the NOVA – School of Business and Economics

CMOS indoor light energy harvesting system for wireless sensing applications

Dissertação para obtenção do Grau de Doutor em Engenharia Electrotécnica e de Computadores

Spectroscopic characterization of natural dyes by their non-invasive identification on pre-Columbian codices: the Maya yellow

Mesoamerican cultures had a strong tradition of written and pictorial manuscripts, called the codices. In studies already performed it was found the use of Maya Blue, made from a mixture of indigo and a clay called palygorskite, forming an incredibly stable material where the dye is trapped inside the nanotubes of the clay, after heating. However, a bigger challenge lies in the study of the yellows used, for these civilizations might have used this clay-dye mixture to produce their yellow colorants. As a first step, it was possible to provide identification, by non-invasive methods, of two colorants (a flavonoid and a carotenoid). While the flavonoid absorbed between 368-379 nm, the carotenoid would absorb around 455 nm. A temperature study also conducted allowed to set 140ºC as the desirable temperature to heat the samples without degrading them. FT-IR, conventional Raman and SERS allowed us to understand the existence of a reaction between the dyes and the clays (palygorskite and kaolinite), however it is difficult to understand it in a molecular point of view. As a second step, five species of Mexican dyes were selected on the basis of historical sources. The Maya yellow samples were produced adapting the recipe proposed by Reyes-Valerio, supporting the yellow dyes extracted from the dried plants on the clays, with addition of water, and then heated at 140ºC. It was found that the addition of water in palygorskite would increase the pH, hence deprotonating the molecules having a clear negative effect in the color. A second recipe was developed, without the addition of water; however, it was found that the use of water based binders would still alter the color of the samples with palygorskite. In this case, kaolinite without heating yield better results as a Maya yellow hybrid. It was found that the Maya chemistry might not have been the same for all the colors. The Mesoamericans might have found that different dyes could work better to their desires if matched with different clays. It was noticeable that for a clear distinction between flavonoids and carotenoids the reflectance and emission studies suffice, but when clay is added, Raman techniques will perform better. For this reason, conventional Raman and SERS were employed in order to create a database for the Mesoamerican dyestuffs for a future identification.

Photochemical degradation of triclosan: a comparison between different light sources

New emerging contaminants could represent a danger to the environment and Humanity with repercussions not yet known. One of the major worldwide pharmaceutical and personal care productions are antimicrobials products, triclosan, is an antimicrobial agent present in most products. Despite the high removal rate of triclosan present in wastewater treatments, triclosan levels are on the rise in the environment through disposal of wastewater effluent and use of sewage sludge in land application. Regulated in the EC/1272/2008 (annex VI, table 3.1), this compound is considered very toxic to aquatic life and it has been reported that photochemical transformation of triclosan produces dioxins. In the current work it was defined three objectives; determination of the most efficient process in triclosan degradation, recurring to photochemical degradation methods comparing different sources of light; identification of the main by-products formed during the degradation and the study of the influence of the Fenton and photo-Fenton reaction. Photochemical degradation methods such as: photocatalysis under florescent light (UV), photocatalysis under visible light (sunlight), photocatalysis under LEDs, photo-Fenton and Fenton reaction have been compared in this work. The degradation of triclosan was visualized through gas chromatography/mass spectrometry (GC/MS). In this study photo-Fenton reaction has successfully oxidized triclosan to H2O and CO2 without any by-products within 2 hours. Photocatalysis by titanium dioxide (TiO2) under LEDs was possible, having a degradation rate of 53% in an 8 hours essay. The degradation rate of the Fenton reaction, UV light and sunlight showed degradation between 90% and 95%. The results are reported to the data observed without statistic support, since this was not possible during the work period. Hydroquinone specie and 2,4-dichlorophenol by-products were identified in the first hour of photocatalysis by UV. A common compound, possibly identified has C7O4H , was present at the degradation by UV, sunlight and LEDs and was concluded to be a contaminant. In the future more studies in the use of LEDs should be undertaken given the advantages of long durability and low consumption of energy of these lamps and that due to their negative impact on the environment fluorescent lamps are being progressively made unavailable by governments, requiring new solutions to be found. Fenton and photo-Fenton reactions can also be costly processes given the expensive reagents used.

Using an LED as a sensor and visible light communication device in a smart illumination system

The need for more efficient illumination systems has led to the proliferation of Solid-State Lighting (SSL) systems, which offer optimized power consumption. SSL systems are comprised of LED devices which are intrinsically fast devices and permit very fast light modulation. This, along with the congestion of the radio frequency spectrum has paved the path for the emergence of Visible Light Communication (VLC) systems. VLC uses free space to convey information by using light modulation. Notwithstanding, as VLC systems proliferate and cost competitiveness ensues, there are two important aspects to be considered. State-of-the-art VLC implementations use power demanding PAs, and thus it is important to investigate if regular, existent Switched-Mode Power Supply (SMPS) circuits can be adapted for VLC use. A 28 W buck regulator was implemented using a off-the-shelf LED Driver integrated circuit, using both series and parallel dimming techniques. Results show that optical clock frequencies up to 500 kHz are achievable without any major modification besides adequate component sizing. The use of an LED as a sensor was investigated, in a short-range, low-data-rate perspective. Results show successful communication in an LED-to-LED configuration, with enhanced range when using LED strings as sensors. Besides, LEDs present spectral selective sensitivity, which makes them good contenders for a multi-colour LED-to-LED system, such as in the use of RGB displays and lamps. Ultimately, the present work shows evidence that LEDs can be used as a dual-purpose device, enabling not only illumination, but also bi-directional data communication.

Light harvesting in solar cells using natural pigments from red fruits adsorbed to mesoporous TiO2

Nature has developed strategies to present us with a wide variety of colours, from the green of leaves to the bright colours seen in flowers. Anthocyanins are between these natural pigments that are responsible for the great diversity of colours seen in flowers and fruits. Anthocyanins have been used to sensitize titanium dioxide (TiO2) in Dye-Sensitized Solar Cells (DSSCs). DSSCs have become one of the most popular research topic in photovoltaic cells due to their low production costs when compared to other alternatives. DSSCs are inspired in what happens in nature during photosynthesis. A primary charge separation is achieved by means of a photoexcited dye capable of performing the electron injection into the conduction band of a wide band-gap semiconductor, usually TiO2. With this work we aimed to synthesize a novel mesoporous TiO2 structure as the semiconductor in order to increase the dye loading. We used natural occurring dyes such as anthocyanins and their synthetic flavylium relatives, as an alternative to the widely used metal complexes of Ru(II) which are expensive and are environmentally unsafe. This offers not only the chance to use safer dyes for DSSCs, but also to take profit of waste biological products, such as wine and olive oil production residues that are heavily loaded with anthocyanin dyes. We also performed a photodegradation study using TiO2 as the catalyst to degrade dye contaminants, such as those from the wine production waste, by photo-irradiation of the system in the visible region of the light spectrum. We were able to succeed in the synthesis of mesoporous TiO2 both powder and thin film, with a high capacity to load a large amount of dye. We proved the concept of photodegradation using TiO2 as catalyst. And finally, we show that wine production waste is a possible dye source to DSSCs application.

Control of a white organic light emitting diode’s emission parameters using a single doped RGB active layer

White Color tuning is an attractive feature that Organic Light Emitting Diodes (OLEDs) offer. Up until now, there hasn’t been any report that mix both color tuning abilities with device stability. In this work, White OLEDs (W-OLEDs) based on a single RGB blend composed of a blue emitting N,N′-Di(1-naphthyl)-N,N′-diphenyl-(1,1′-biphenyl)-4,4′-diamine (NPB) doped with a green emitting Coumarin-153 and a red emitting 4-(Dicyanomethylene)-2-methyl-6-(4-dimethylaminostyryl)-4H-pyran (DCM1) dyes were produced. The final device structure was ITO/Blend/Bathocuproine (BCP)/ Tris(8-hydroxyquinolinato)aluminium (Alq3)/Al with an emission area of 0.25 cm2. The effects of the changing in DCM1’s concentration (from 0.5% to 1% wt.) allowed a tuning in the final white color resulting in devices capable of emitting a wide range of tunes – from cool to warm – while also keeping a low device complexity and a high stabilitty. Moreover, an explanation on the optoelectrical behavior of the device is presented. The best electroluminescense (EL) points toward 160 cd/m2 of brightness and 1.1 cd/A of efficiency, both prompted to being enhanced. An Impedance Spectroscopy (IS) analysis allowed to study both the effects of BCP as a Hole Blocking Layer and as an aging probe of the device. Finally, as a proof of concept, the emission was increased 9 and 64 times proving this structure can be effectively applied for general lighting.

The effect of energy and traffic light labeling on parents purchasing decisions of cereals for their children

Objective: Nutritional labeling systems are considered a tool to fight obesity since they aim to contribute for more informed food choices as well as assist consumers to make healthier nutrition options and in this manner, contribute to a decrease in the obesity rate. This study intends to analyze the effect of different types of labeling systems on parents’ purchasing decisions for their children on a specific product: breakfast cereals. More precisely, how labels affect parents’ perception of healthiness regarding cereals and if the nutritional information has an effect on intended purchases for their children. Participants and methods: We conducted a study with 135 Portuguese parents of children aged 4 to12 years. Parents answered a questionnaire with one of three hypothetical cereals menus. Menus only differed in their nutritional labeling technique: no labels (control group), reference intake labels or traffic light labels. In addition, we conducted 20 face-to-face interviews to a different group of parents in order to perform a recall task. Findings: This paper provides no evidence to suggest that energy labeling or traffic light labeling systems alone were successful in helping parents making healthy purchases of cereals for their children. Therefore, there is the need to promote supplementary policies to encourage the consumption of healthier food and help fight obesity.