The Cristo Rei section (Lower Miocene). Distal fluviatile environments in a marine series, plants, vertebrates and other evidence, age

The section at Cristo Rei shows sandy beds with intercalated clayey lenses (IVb division from the Lisbon Miocene series) that correspond to a major regression event dated from between ca. 17.6 and 17 Ma. They also correspond to a distal position (relatively to the typical fluviatile facies in Lisbon), nearer the basin's axis. Geologic data and paleontological analysis (plant fossils, fishes, crocodilians, land mammals) allow the reconstruction of environments that were represented in the concerned area: estuary with channels and ox-bows; upstream, areas occupied by brackish waters where Gryphaea griphoides banks developped; still farther upstream, freshwaters sided by humid forests and low mountain subtropical forests under warm temperate and rainy conditions, as well as not far away, seasonally dry environments (low density tree or shrub cover, or steppe).

Toarcian GSSP candidate: the Peniche section at Ponta do Trovão

The Peniche section (Ponta do Trovão) in Portugal is presented as potential stratotype (GSSP) for the Pliensbachian/Toarcian boundary. The lithostratigraphic succession is described and the chronostratigraphy, based on ammonite assemblages, is presented; the change in foraminifera assemblages occurs later, only at the base of beds 16 (base of Semicelatum Subzone, Crosbeyi ? Horizon). An extensive bibliographical list of all scientific articles containing specific reference to this stratigraphic boundary, whether from the Lusitanian or Algarve basins, is also presented.

Calcareous nannofossil assemblages around the Pliensbachian/Toarcian boundary in the reference section of Peniche (Portugal)

The Pliensbachian/Toarcian boundary (Lower Jurassic) is well represented in the Lusitanian Basin (Portugal), mainly in the Peniche area, recorded by a marl/limestone series. Calcareous nannofossil assemblages are described herein, with the aim to contribute to the Toarcian GSSP definition. Marly samples were collected 3 m below and 7 m above this boundary and analysed for calcareous nannofossils. The main nannofossils observed were Biscutum finchii, B. grande, Calcivascularis jansae, Crepidolithus crassus, C. granulatus, C. impontus, Lotharingius hauffii, L. sigillatus, L. aff. L. velatus, Schizosphaerella spp. and Tubirhabdus patulus. This assemblage indicates that the Pliensbachian/Toarcian boundary in Peniche lies in the upper part of the NJ5b Subzone. Schizosphaerella and Lotharingius dominate the assemblage. The abundant occurrence of C. jansae and the common occurrence of B. grande indicate a strong Tethyan influence.

Calcareous nannofossil assemblages across the Pliensbachian/Toarcian boundary at the Peniche section (Ponta do Trovão, Lusitanian Basin)

The Peniche section has revealed moderately-to-well preserved calcareous nannofossil assemblages across the Pliensbachian/Toarcian boundary. This good record has allowed the proposition of a refined biostratigraphic scheme. The stage boundary, as defined by ammonites, is comprised within the NJ5b C. impontus (NW Europe; BOWN & COOPER, 1998) or the NJT5b L. sigillatus (Mediterranean Tethys; MATTIOLI & ERBA, 1999) nannofossil subzones. Since in the Lusitanian Basin a mixing of N- and S-Tethyan taxa is observed, both biozonation schemes can be applied. Some nannofossil events (mainly first occurrences) are observed earlier in Portugal than in other Tethyan settings. It is still unclear if these events are real first occurrences. A diversification phase occurred across the Pliensbachian/Toarcian boundary. This phase is well recorded at Peniche, where a change is observed passing from the Pliensbachian, when assemblages are dominated by muroliths, to the Toarcian showing assemblages where placoliths are abundant. A quantification of nannofossils per gram of rock shows that absolute abundances are the highest across the Pliensbachian/Toarcian boundary. Indeed, Peniche exhibits nannofossil abundances very high with respect to correlative levels in other Tethyan settings. The pelagic carbonate fraction (produced by nannofossils) is important in the marly hemi-couplets of Peniche. In some levels, nannofossils account for more than 50% of the total carbonate fraction.

In situ measured cross section geometry of old timber structures and its influence on structural safety

Old timber structures may show significant variation in the cross section geometry along the same element, as a result of both construction methods and deterioration. As consequence, the definition of the geometric parameters in situ may be both time consuming and costly. This work presents the results of inspections carried out in different timber structures. Based on the obtained results, different simplified geometric models are proposed in order to efficiently model the geometry variations found. Probabilistic modelling techniques are also used to define safety parameters of existing timber structures, when subjected to dead and live loads, namely self-weight and wind actions. The parameters of the models have been defined as probabilistic variables, and safety of a selected case study was assessed using the Monte Carlo simulation technique. Assuming a target reliability index, a model was defined for both the residual cross section and the time dependent deterioration evolution. As a consequence, it was possible to compute probabilities of failure and reliability indices, as well as, time evolution deterioration curves for this structure. The results obtained provide a proposal for definition of the cross section geometric parameters of existing timber structures with different levels of decay, using a simplified probabilistic geometry model and considering a remaining capacity factor for the decayed areas. This model can be used for assessing the safety of the structure at present and for predicting future performance.

A look into the cross-section of industry stock returns

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Finance from the NOVA – School of Business and Economics

Strengthening to seismic action of reinforced columns with rectangular cross-section

The first part of this research work regards the assessment of the mathematical modelling of reinforced concrete columns confined with carbon fibre (CFRP) sheets under axial loading. The purpose was to evaluate existing analytical models, contribute to possible improvements and choose the best model(s) to be part of a new model for the prediction of the behaviour of confined columns under bending and compression. For circular columns, a wide group of authors have proposed several models specific for FRP-confined concrete. The analysis of some of the existing models was carried out by comparing these with several tested columns. Although several models predict fairly the peak load only few can properly estimate the load-strain and dilation behaviour of the columns. Square columns confined with CFRP show a more complex interpretation of their behaviour. Accordingly, the analysis of two experimental programs was carried out to propose new modelling equations for the whole behaviour of columns. The modelling results show that the analytical curves are in general agreement with the presented experimental curves for a wide range of dimensions. An analysis similar to the one done for circular columns was this turn carried out for square columns. Few models can fairly estimate the whole behaviour of the columns and with less accuracy at all levels when compared with circular columns. The second part of this study includes seven experimental tests carried out on reinforced concrete rectangular columns with rounded corners, different damage condition and with confinement and longitudinal strengthening systems. It was concluded that the use of CFRP confinement is viable and of effective performance enhancement alone and combined with other techniques, maintaining a good ductile behaviour for established threshold displacements. As regards the use of external longitudinal strengthening combined with CFRP confinement, this system is effective for the performance enhancement and viable in terms of execution. The load capacity was increased significantly, preserving also in this case a good ductile behaviour for threshold displacements. As to the numerical nonlinear modelling of the tested columns, the results show a variation of the peak load of 1% to 10% compared with tests results. The good results are partly due to the inclusion of the concrete constitutive model by Mander et al. modified by Faustino, Chastre & Paula taking into account the confinement effect. Despite the reasonable approximation to tests results, the modelling results showed higher unloading, which leads to an overestimate dissipated energy and residualdisplacement.