Simulação numérica da propagação e rebentação de ondas utilizando o código OpenFoam

Esta dissertação teve o intuito de validar o código numérico do OpenFoam para problemas na área da hidrodinâmica e propagação de ondas. Para a geração de ondas através do código numérico recorreu-se ao solver Waves2Foam, uma ferramenta do OpenFoam baseada no InterFoam, solver baseado no método VoF (Volume of fluid) com a implementação de zonas de relaxamento para a geração e dissipação da energia das ondas. Os casos simulados nesta dissertação tiveram o objectivo de testar a ferramenta para diferentes condições de propagação de ondas e diferentes teorias. Assim é apresentado um caso bidimensional com fundo horizontal e profundidade considerada infinita e outro bidimensional com fundo variável de forma a verificar a ocorrência ou não de rebentação, ambos para ondas regulares de primeira ordem ou ondas de Airy. Além dos casos bidimensionais também são apresentados dois casos tridimensionais com fundo variável, para ondas regulares e bicromáticas e em situação com e sem rebentação. Tanto o caso bidimensional de profundidade variável como o primeiro caso tridimensional foram baseados em ensaios e dados experimentais realizados num canal de profundidade variável para ondas regulares em situação com e sem rebentação. O segundo caso tridimensional também foi baseado em ensaios experimentais no mesmo canal de fundo variável para ondas geradas bicromáticas em situação com e sem rebentação. Através das simulações realizadas pode-se concluir que para casos de propagação de ondas sem rebentação o solver Waves2Foam obtém bons resultados. Já nos casos com rebentação os resultados apresentam alguma discrepância devida à não utilização de modelos de turbulência. No geral, o código numérico do OpenFoam dá bons resultados para resolver problemas de hidrodinâmica através de ondas regulares e de ondas bicromáticas.

Role of surfactants in filtration and fouling of colloidal silica

The EM3E Master is an Education Programme supported by the European Commission, the European Membrane Society (EMS), the European Membrane House (EMH), and a large international network of industrial companies, research centres and universities

Design and development of a microfluidic platform for use with colorimetric gold nanoprobe assays

Due to the importance and wide applications of the DNA analysis, there is a need to make genetic analysis more available and more affordable. As such, the aim of this PhD thesis is to optimize a colorimetric DNA biosensor based on gold nanoprobes developed in CEMOP by reducing its price and the needed volume of solution without compromising the device sensitivity and reliability, towards the point of care use. Firstly, the price of the biosensor was decreased by replacing the silicon photodetector by a low cost, solution processed TiO2 photodetector. To further reduce the photodetector price, a novel fabrication method was developed: a cost-effective inkjet printing technology that enabled to increase TiO2 surface area. Secondly, the DNA biosensor was optimized by means of microfluidics that offer advantages of miniaturization, much lower sample/reagents consumption, enhanced system performance and functionality by integrating different components. In the developed microfluidic platform, the optical path length was extended by detecting along the channel and the light was transmitted by optical fibres enabling to guide the light very close to the analysed solution. Microfluidic chip of high aspect ratio (~13), smooth and nearly vertical sidewalls was fabricated in PDMS using a SU-8 mould for patterning. The platform coupled to the gold nanoprobe assay enabled detection of Mycobacterium tuberculosis using 3 8l on DNA solution, i.e. 20 times less than in the previous state-of-the-art. Subsequently, the bio-microfluidic platform was optimized in terms of cost, electrical signal processing and sensitivity to colour variation, yielding 160% improvement of colorimetric AuNPs analysis. Planar microlenses were incorporated to converge light into the sample and then to the output fibre core increasing 6 times the signal-to-losses ratio. The optimized platform enabled detection of single nucleotide polymorphism related with obesity risk (FTO) using target DNA concentration below the limit of detection of the conventionally used microplate reader (i.e. 15 ng/μl) with 10 times lower solution volume (3 μl). The combination of the unique optical properties of gold nanoprobes with microfluidic platform resulted in sensitive and accurate sensor for single nucleotide polymorphism detection operating using small volumes of solutions and without the need for substrate functionalization or sophisticated instrumentation. Simultaneously, to enable on chip reagents mixing, a PDMS micromixer was developed and optimized for the highest efficiency, low pressure drop and short mixing length. The optimized device shows 80% of mixing efficiency at Re = 0.1 in 2.5 mm long mixer with the pressure drop of 6 Pa, satisfying requirements for the application in the microfluidic platform for DNA analysis.

Double-walled PLLA/PLGA particles for the sustained release of Meloxicam: preparation, characterisation and contolled release studies

There were two main objectives in this thesis investigation, first, the production, characterisation, in vitro degradation and release studies of double walled microspheres for drug release control. The second one, and the most challenging, was the production of double walled nanospheres, also for drug control delivery. The spheres were produced using two polymers, the Poly(L-lactide)Acid, PLLA, and the Poly(L-lactide-co-glycolic)Acid, PLGA.Afterwards, a model drug, Meloxicam, which is an antiinflammatory drug, was encapsulated into the particles. Micro and nanospheres were produced by the solvent extraction/evaporation method, where perfect spherical particles were obtained. By varying the polymers PLLA/PLGA mass ratio, different core and shell composition, as well as several shell and core thickness were observed. In the particles with a PLLA/PLGA mass ratio 1:1, the shell is composed by PLLA and the core by PLGA. It was also verified that the Meloxicam has a tendency to be distributed in the PLGA layer. Micro and nanoparticles were characterised in morphology, size, polymer cristalinity properties and drug distribution. Particles degradation studies was performed, where the particles in a PVA solution of pH 7,4 where placed in an incubator, during approximately 40 days, at 120rpm, and 37ºC, simulating, as much as possible, the human body environment. From these studies, the conclusion was that particles containing a PLGA shell and a PLLA core degrade more rapidly, due to the fact that PLLA is more hydrophobic than the PLGA. Concerning the drug release controlled results, done also for 40 and 50 days, they showed that the microspheres containing a shell of PLLA release more slowly than when the shell is composed of PLGA. This result was predictable, since the drug is solubilised in the PLGA polymer and so, in that case, the PLLA shell works like a barrier between the drug and the outer medium. Another positive aspect presented by this study is the lower initial burst effect, obtained when using double walled particles, which is one of the advantages of the same. In a second part of this investigation, the production of the nanospheres was the main goal, since it was not yet accomplished by other authors or investigators. After several studies, referring to the speed, time and type of agitation, as well as, the concentration and volume of the first aqueous solution of poly-vinyl-alcohol (PVA) during the process of solvent extraction/evaporation it was possible to obtain double walled nanospheres.(...)

Essays in health economics: Volume-Outcome Effect, upcoding behaviour and the evaluation of a short-term intervention program

Evidence in the literature suggests a negative relationship between volume of medical procedures and mortality rates in the health care sector. In general, high-volume hospitals appear to achieve lower mortality rates, although considerable variation exists. However, most studies focus on US hospitals, which face different incentives than hospitals in a National Health Service (NHS). In order to add to the literature, this study aims to understand what happens in a NHS. Results reveal a statistically significant correlation between volume of procedures and better outcomes for the following medical procedures: cerebral infarction, respiratory infections, circulatory disorders with AMI, bowel procedures, cirrhosis, and hip and femur procedures. The effect is explained with the practice-makes-perfect hypothesis through static effects of scale with little evidence of learning-by-doing. The centralization of those medical procedures is recommended given that this policy would save a considerable number of lives (reduction of 12% in deaths for cerebral infarction).