11 resultados para organic electronics semiconductors detectors sensors X-rays
Resumo:
In this thesis was investigated the radiation hardness of the building blocks of a future flexible X-ray sensor system. The characterized building blocks for the pixel addressing and signal amplification electronics are high mobility semiconducting oxide transistors (HMSO-TFTs) and organic transistors (OTFTs), whereas the photonic detection system is based on organic semiconducting single crystals (OSSCs). TFT parameters such as mobility, threshold voltage and subthreshold slope were measured as function of cumulative X-ray dose. Instead for OSSCs conductivity and X-ray sensitivity were analysed after various radiation steps. The results show that ionizing radiation does not lead to degradation in HMSO-TFTs. Instead OTFTs show instability in mobility which is reduced up to 73% for doses of 1 kGy. OSSC demonstrate stable detector properties for the tested total dose range. As conclusion, HMSO-TFTs and OSSCs can be readily employed in the X-ray detector system allowing operation for total doses exceeding 1 kGy of ionizing radiation.
Resumo:
RESUMO - Na radiologia de intervenção, e concretamente em ortopedia, os raios X são intensamente utilizados permitindo a visualização de diversas técnicas de intervenção cirúrgica. Do ponto de vista médico as vantagens dessa prática são enormes, contudo, os profissionais de saúde envolvidos são susceptíveis de estarem expostos a valores de dose de radiação que significam a sua classificação como trabalhadores expostos. O presente estudo realizou-se num hospital e teve como objectivo obter uma estimativa das doses envolvidas em ortopedia de intervenção, utilizando várias metodologias experimentais para caracterização do campo de radiação primário e secundário. Observaram-se distintos níveis de dose de acordo com a zona anatómica exposta à radiação X: (i) gónadas — 0,02 a 3 mGy/h; (ii) cristalino — 0,06 a 1 mGy/h e (iii) mãos — 0,6 mGy/h. Tais resultados evidenciam uma clara necessidade de utilização de equipamentos de protecção e de vigilância dosimétrica pelos profissionais de saúde envolvidos no acto cirúrgico.--------------------------ABSTRACT - In intervention radiology, and more specifically in orthopaedics, X-rays are intensely used allowing the visualization of many acts of clinical intervention. From a clinical perspective, the advantages of that practice are significant; however, involved health care professionals are susceptible of being exposed to radiation dose values that mean their classification as exposed workers. The present study, performed in a hospital, aimed to obtain an estimation of the doses involved in intervention orthopaedics through several experimental methodologies in order to characterise the primary and the secondary radiation fields. Different levels of dose were observed according to the anatomic area exposed to X radiation: (i) gonads — 0.02 a 3 mGy/h; (ii) crystalline lens — 0.06 a 1 mGy/h e (iii) hands – 0.6 mGy/h. Such results denote a clear need of protection equipment use and of dosimetric surveillance by the health
Resumo:
Superoxide reductase is a 14 kDa metalloprotein containing a catalytic nonhaem iron centre [Fe(His)4Cys]. It is involved in defence mechanisms against oxygen toxicity, scavenging superoxide radicals from the cell. The oxidized form of Treponema pallidum superoxide reductase was crystallized in the presence of polyethylene glycol and magnesium chloride. Two crystal forms were obtained depending on the oxidizing agents used after purification: crystals grown in the presence of K3Fe(CN)6 belonged to space group P21 (unit-cell parameters a = 60.3, b = 59.9, c = 64.8 A ° , = 106.9 ) and diffracted beyond 1.60 A ° resolution, while crystals grown in the presence of Na2IrCl6 belonged to space group C2 (a = 119.4, b = 60.1, c = 65.6 A ° , = 104.9 ) and diffracted beyond 1.55 A ° . A highly redundant X-ray diffraction data set from the C2 crystal form collected on a copper rotating-anode generator ( = 1.542 A ° ) clearly defined the positions of the four Fe atoms present in the asymmetric unit by SAD methods. A MAD experiment at the iron absorption edge confirmed the positions of the previously determined iron sites and provided better phases for model building and refinement. Molecular replacement using the P21 data set was successful using a preliminary trace as a search model. A similar arrangement of the four protein molecules could be observed.
Resumo:
J Biol Inorg Chem (2006) 11: 548–558 DOI 10.1007/s00775-006-0104-y
Resumo:
Fundação para a Ciência e Tecnologia - EXPL/BBB-BEP/0274/2012
Resumo:
É sabido que devido à escassez de água potável, nomeadamente em países sub-desenvolvidos, morrem milhares de pessoas por ano, com a procura de fontes de água alternativas, que por sua vez se encontram contaminadas com microrganismos patogénicos; a este facto também se salienta a possibilidade de ocorrência de catástrofes naturais, tornando-se necessário o desenvolvimento de sistemas de desinfecção prácticos, de baixo custo e eficientes. O trabalho experimental desenvolvido focou-se nestas realidades, tendo por objectivo principal o desenvolvimento de um papel bactericida, em particular, um papel de baixo custo como é o caso do papel de filtro de café, para aplicação em desinfecção de água. Este papel foi funcionalizado com nanopartículas sintetizadas de prata, óxido de zinco e com ambas, assim como com nanopartículas comerciais, cuja caracterização foi feita por Microscopia Electrónica de Varrimento (SEM, Scanning Electron Microscopy), Energia Dispersiva de Raios-X (EDS, Energy-dispersive X-ray Spectroscopy), Espectroscopia de Ultravioleta-Visível (UV-VIS Uv-Visible Spectroscopy), Difracção de Raios-X (DRX, X-Rays Diffraction), Análise Termogravimétrica (TA, Thermal Analysis), e Calorimetria Diferencial de Varrimento (DSC, Differencial Scanning Calorimetry) e a actividade anti-bacteriana dos papéis foi avaliada através de Testes de Sensibilidade aos Antibióticos, pelo Método de Kirby-Bauer, contra as bactérias S.a.ATCC25923 e E.coli ATCC25922. No decorrer das sínteses variaram-se alguns parâmetros consoante o tipo de nanopartícula, para as np´s de prata variou-se essencialmente a metodologia de síntese e o tipo de redutor, para as np´s de óxido de zinco, dado ser um composto fotossensível, submeteu-se o papel á luz ultravioleta, o que, por outro lado também esterelizava o papel, e para ter uma comparação, esterelizou-se também o papel pela autoclave, constatando-se, pelas técnicas de caracterização, nomeadamente DRX, que os papeis não continham nanopartículas de óxido de zinco mas sim de acetato de zinco. Surpreendentemente, nos papéis autoclavados já se detectou a presença de óxido de zinco. Com os papéis que evidenciararam maior actividade anti-bacteriana realizaram-se filtrações de membrana com amostras de água contaminada e a determinação da concentração de metal no filtrado foi realizada pela técnica de Espectroscopia de Absorção Atómica de Chama (Flame Atomic Absorption Spectroscopy) conseguindo-se uma taxa de redução bacteriana de practicamente 100% para E.coli NCTC 9001 e E.f NCTC775 com os papéis contendo acetato de zinco numa concentração de 50 mM e np´sAg e acetato de zinco, numa concentração de 10 mM. De forma a validar o trabalho desenvolvido a parte final consistiu em testar os filtros com melhores propriedades em águas contaminadas, tendo esse trabalho sido feito no Laboratório de Água de Consumo dos Serviços Municipalizados de Água e Saneamento de Almada.
Resumo:
Dissertação para obtenção do Grau de Doutor em Química
Resumo:
Nowadays, existing 3D scanning cameras and microscopes in the market use digital or discrete sensors, such as CCDs or CMOS for object detection applications. However, these combined systems are not fast enough for some application scenarios since they require large data processing resources and can be cumbersome. Thereby, there is a clear interest in exploring the possibilities and performances of analogue sensors such as arrays of position sensitive detectors with the final goal of integrating them in 3D scanning cameras or microscopes for object detection purposes. The work performed in this thesis deals with the implementation of prototype systems in order to explore the application of object detection using amorphous silicon position sensors of 32 and 128 lines which were produced in the clean room at CENIMAT-CEMOP. During the first phase of this work, the fabrication and the study of the static and dynamic specifications of the sensors as well as their conditioning in relation to the existing scientific and technological knowledge became a starting point. Subsequently, relevant data acquisition and suitable signal processing electronics were assembled. Various prototypes were developed for the 32 and 128 array PSD sensors. Appropriate optical solutions were integrated to work together with the constructed prototypes, allowing the required experiments to be carried out and allowing the achievement of the results presented in this thesis. All control, data acquisition and 3D rendering platform software was implemented for the existing systems. All these components were combined together to form several integrated systems for the 32 and 128 line PSD 3D sensors. The performance of the 32 PSD array sensor and system was evaluated for machine vision applications such as for example 3D object rendering as well as for microscopy applications such as for example micro object movement detection. Trials were also performed involving the 128 array PSD sensor systems. Sensor channel non-linearities of approximately 4 to 7% were obtained. Overall results obtained show the possibility of using a linear array of 32/128 1D line sensors based on the amorphous silicon technology to render 3D profiles of objects. The system and setup presented allows 3D rendering at high speeds and at high frame rates. The minimum detail or gap that can be detected by the sensor system is approximately 350 μm when using this current setup. It is also possible to render an object in 3D within a scanning angle range of 15º to 85º and identify its real height as a function of the scanning angle and the image displacement distance on the sensor. Simple and not so simple objects, such as a rubber and a plastic fork, can be rendered in 3D properly and accurately also at high resolution, using this sensor and system platform. The nip structure sensor system can detect primary and even derived colors of objects by a proper adjustment of the integration time of the system and by combining white, red, green and blue (RGB) light sources. A mean colorimetric error of 25.7 was obtained. It is also possible to detect the movement of micrometer objects using the 32 PSD sensor system. This kind of setup offers the possibility to detect if a micro object is moving, what are its dimensions and what is its position in two dimensions, even at high speeds. Results show a non-linearity of about 3% and a spatial resolution of < 2µm.
Resumo:
Dissertation to obtain the academic degree of Master in materials engineering submitted to the Faculty of science and engineering of Universidade Nova de Lisboa
Resumo:
Portuguese Science Foundation - project Electra PTDC/CTM/099124/2008 and the PhD grant SFRH/BD/45224. financial support: Professor E. Fortunato’s ERC 2008 Advanced Grant (INVISIBLE contract number 228144), “APPLE” FP7-NMP-2010-SME/262782-2 and “SMARTEC” FP7-ICT-2009.3.9/258203
Resumo:
Dissertation to obtain the degree of Master in Chemical and Biochemical Engineering