Experimental study of proton induced nuclear reactions in 6,7 Li

This work presents the results of the experimental study of proton induced nuclear reactions in lithium, namely the 7Li(p,α) 4He, 6Li(p,α) 3He and 7Li(p,p)7Li reactions. The amount of 7Li and 6Li identified as primordial and observed in very old stars of the Milky Way galactic halo strongly deviates from the predictions of primordial nucleosynthesis and stellar evolution models which depend, among other factors, on the cross sections of reactions like 7Li(p,α) 4He and 6Li(p,α) 3He. These discrepancies have triggered a large amount of research in the fields of stellar evolution, cosmology, pre-galactic evolution and low energy nuclear reactions. Focusing on nuclear reactions, this work has measured the 7Li(p,α) 4He and 6Li(p,α) 3He reactions cross sections (expressed in terms of the astrophysical S -factor) with higher accuracy, and the electron screening effects in these reactions for different environments (insulators and metallic targets). The 7Li(p,α) 4He angular distributions were also measured. These measurementstook place in two laboratory facilities, in the framework of the LUNA (Laboratory for Undergroud Nuclear Astrophysics) international collaboration, namely the Laboratorio ´ de Feixe de Ioes ˜ in ITN (Instituto Tecnologico ´ e Nuclear) Sacavem, ´ Portugal, and the Dynamitron-TandemLaboratorium in Ruhr-Universitat¨ Bochum, Germany. The ITN target chamber was modified to measure these nuclear reactions, with the design and construction of new components, the addition of one turbomolecular pump and a cold finger. The 7Li(p,α) 4He and 6Li(p,α) 3He reactions were measured concurrently with seven and four targets, respectively. These targets were produced in order to obtain adequate and stable lithium depth profiles. In metallic environments, the measured electron screening potential energies are much higher than the predictions of atomic-physics models. The Debye screening model applied to the metallic conduction electrons is able to explain these high values. It is a simple model, but also very robust. Concerning primordial nucleosynthesis and stellar evolution models, these results are very important as they show that laboratory measurements are well controlled, and the model inputs from these cross sections are therefore correct. In this work the 7Li(p,p)7Li differential cross section was also measured, which is useful to describe the 7Li(p,α) 4He entrance channel.

A first analysis of the atmospheric measurements from TANSO/GOSAT

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau em Mestre em Engenharia Física

New analytical methodologies for doping control – detection of anabolic androgenic steroids in human urine

Dissertation submitted to Faculdade de Ciências e Tecnologia - Universidade Nova de Lisboa in fulfilment of the requirements for the degree of Doctor of Philosophy (Biochemistry - Biotechnology)

Development of new methodologies in sample treatment for proteomics workflow based on enzymatic probe sonication technology and mass spectrometry

Thesis submitted to the Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia, for the degree of Doctor of Philosophy in Biochemistry

Análise da estrutura e da função da proteína morfogenética RodZ de Bacillus subtilis

Resumo: RodZ é um componente do sistema morfogenético das células bacterianas. É uma proteína transmembranar que localiza em bandas ao longo do eixo longitudinal da célula. Em Bacillus subtilis, RodZ consiste numa porção citoplasmática, RodZn, e em uma parte extra-citoplasmática, RodZc. RodZn contém um domínio em helixturn- helix (HTH), enquanto que RodZc pode ser dividido num domínio coiled-coil e num domínio terminal C, de função desconhecida. Um segmento transmembranar (TM) único separa RodZn de RodZc. A eliminação de rodZ causa alongamento do nucleóide e leva à produção de células polares nucleadas. Aqui, mostramos que RodZn é estruturado, estável e em hélice α. Descobrimos que as substituições Y32A e L33A na suposta hélice de reconhecimento (3) do motivo HTH, bem como as substituições Y49A e F53A, fora do motivo HTH (4), causam divisão assimétrica, mas apenas as últimas levam à deslocalização sub-celular de RodZ. Sugerimos que as hélices 3 e 4 são utilizadas para uma interacção proteína-proteína ou proteína- DNA essencial para divisão celular enquanto que 4 deve contactar um componente do citosqueleto, possivelmente MreB, uma vez que a correcta localização sub-celular de RodZ depende desta proteína. Em todos os mutantes as células polares são anucleadas, pelo que concluímos que o alongamento do nucleóide não é um prérequisito para divisão assimétrica. RodZc é largamente não estruturado mas com conteúdo de folha , sendo estabilizado pelo domínio coiled-coil. Mostramos uma relação homóloga entre RodZc e a bomba de transporte Na+/Ca2+ NCX1 e identificámos dois resíduos no domínio C, G265 e N275, essenciais para a manutenção da forma celular. Estes resíduos fazem parte de um motivo em gancho que pode actuar como um local de interacção com um ligando desconhecido. RodZn e RodZc são monoméricos em solução. Contudo, na membrana, RodZ interage consigo própria num sistema de dois híbridos (Split-Ubiquitin) em levedura, sugerindo que possa formar multímeros in vivo.-----------ABSTRACT: RodZ is a transmembrane component of the bacterial core morphogenic apparatus. RodZ localizes in bands long the longitudinal axis of the cell, and it is though to functionally link the cell wall to the actin cytoskeleton. In Bacillus subtilis, RodZ consists of a cytoplasmic moiety, RodZn, and an extracytoplasmic moiety, RodZc. RodZn contains a predicted helix-turn-helix domain, whereas RodZc is thought to contain a coiled-coil region and a terminal C domain of unknown function. A single transmembrane domain separates RodZn from RodZc. Deletion of rodZ causes elongation of the nucleoid and leads to the production of polar minicells containing DNA. Here, we have studied the structure and function of RodZn and RodZc. We show that RodZn is a stable, folded, -helical domain. We discovered that the Y32A and L33A substitutions within the presumptive recognition helix (3) of the HTH motif, as well as the Y49A and F53A substitutions outside of the HTH motif (in 4) cause asymmetric cell division. However, only the substitutions in 4 cause sub-celular delocalization of RodZ. We suggest that 3 and 4 are used for a protein-protein or protein-DNA interaction important for cell division, whereas 4 is likely to contact a cytoskeletal component, presumably MreB. The polar cells formed by all the mutants are anucleate. We conclude that nucleoid elongation is not a prerequisite for asymmetric division. RodZc appears to be a largely unstructured domain, with some -sheet content, and is stabilized by the coiled-coil region. We show a homology relationship between RodZc and the NCX1 Na+/Ca2+ transporter and we found two residues within the C domain, G265 and N275, that are important for cell shape determination. These residues are predicted to be essential determinants of a claw-like motif, which may act as a binding site for an unknown ligand. Both the isolated RodZn and RodZc proteins are monomeric in solution. However, because full-length RodZ interacts with itself in a split-ubiquitin yeast two-hybrid assay, we suggest that it may dimerize or form higher order multimers in vivo.

Insight into the multicopper oxidases stability

Dissertation presented to obtain the PhD degree in Biochemistry

Towards cryogenic liquid –vapor energy storage units for space applications

Dissertation to obtain the Doctoral degree in Physics Engineering

A low-voltage RF-CMOS receiver front-end for a wireless fall detection microsystem

Dissertação para obtenção do Grau de Mestre em Engenharia Eletrotécnica e de Computadores, pela Universidade Nova de Ciências e Tecnologia

Hydrogen permeation in parabolic trough receivers

The continued economic and population development puts additional pressure on the already scarce energetic sources. Thus there is a growing urge to adopt a sustainable plan able to meet the present and future energetic demands. Since the last two decades, solar trough technology has been demonstrating to be a reliable alternative to fossil fuels. Currently, the trough industry seeks, by optimizing energy conversion, to drive the cost of electricity down and therefore to place itself as main player in the next energetic age. One of the issues that lately have gained considerable relevance came from the observation of significant heat losses in a large number of receiver modules. These heat losses were attributed to slow permeation of traces of hydrogen gas through the steel tube wall into the vacuum annulus. The presence of hydrogen gas in the absorber tube results from the decomposition of heat transfer fluid due to the long-term exposure to 400°C. The permeated hydrogen acts as heat conduction mean leading to a decrease in the receivers performance and thus its lifetime. In order to prevent hydrogen accumulation, it has been common practice to incorporate hydrogen getters in the vacuum annulus of the receivers. Nevertheless these materials are not only expensive but their gas absorbing capacity can be insufficient to assure the required level of vacuum for the receivers to function. In this work the building of a permeation measurement device, vulnerabilities detected in the construction process and its overcome are described. Furthermore an experimental procedure was optimized and the obtained permeability results, of different samples were evaluated. The data was compared to measurements performed by an external entity. The reliability of the comparative data was also addressed. In the end conclusions on the permeability results for the different samples characteristics, feasibility of the measurement device are drawn and recommendations on future line of work were made.

Towards printed carbon nanotube transistors on paper substrates

This thesis reports the work performed in the optimization of deposition parameters of Multi – Walled Carbon Nanotubes (MWCNT) targeting the development of a Field Effect Transistors (FET) on paper substrates. The CNTs were dispersed in a water solution with sodium dodecyl sulphate (SDS) through ultrasonication, ultrasonic bath and a centrifugation to remove the supernatant and have a homogeneous solution. Several deposition tests were performed using different types of CNTs, dis-persants, papers substrates and deposition techniques, such as spray coating and inkjet printing. The characterization of CNTs was made by Scanning Electron Microscopy (SEM) and Hall Effect. The most suitable CNT coatings able to be used as semiconductor in FETs were deposited by spray coat-ing on a paper substrate with hydrophilic nanoporous surface (FS2) at 100 ºC, 4 bar, 10 cm height, 5 second of deposition time and 90 seconds of drying between steps (4 layers of CNTs were deposited). Planar electrolyte gated FETs were produced with these layers using gold-nickel gate, source and drain electrodes. Despite the small current modulation (Ion/Ioff ratio of 1.8) one of these devices have p-type conduction with a field effect mobility of 1.07 cm2/V.s.

A Problemática da Erosão Costeira: O Caso Específico da Praia do Pedrógão

Ao longo das últimas décadas, tem-se verificado uma crescente ocupação populacional e urbanística, em paralelo com a concentração de diversas actividades económicas, ao longo das zonas costeiras. Neste sentido, torna-se fulcral o desenvolvimento de políticas de gestão integrada destes ecossistemas naturais, dada a sua grande vulnerabilidade, no que respeita aos usos e ocupação do solo. Como resultado de acções naturais e do Homem (na sua grande maioria), a erosão estabelece-se como o principal problema que assola as zonas costeiras, em Portugal. Neste sentido, as Tecnologias de Informação Geográfica, em especial os Sistemas de Informação Geográfica, conferem-se como importantes ferramentas, tanto na monitorização do litoral, como no apoio aos processos de tomada de decisão. A presente dissertação detém, como principal objectivo, demonstrar as mais-valias dos SIG no estudo das zonas costeiras, especialmente na área da prevenção. Tendo como área de estudo a praia do Pedrógão, em Leiria, considerando o período temporal 1947 – 2014 (1947-1983; 1983-2003; 2003-2007; 2007-2012; 2012-2014), propõe-se: estabelecer uma base cartográfica que analise, espacialmente, o comportamento da linha da costa face à gradual erosão; quantificar as taxas de erosão/acreção e, por fim, proceder à delimitação de faixas de perigo, em paralelo com a análise dos resultados previamente conseguidos, assim como da topografia do local em análise. Para o troço costeiro seleccionado, é de constatar que existe, efectivamente, um recuo da linha da costa, especialmente na praia Sul (Praia dos Campistas), onde se regista o maior recuo médio anual (-17.72m, entre 2012-2014). Na praia Norte, as v taxas anuais variam entre os -0.64m (1947-1983) e os -15.07m (2012-2014), tendo apresentado valores de acreção, com excepção para o intervalo de tempo mais recente. É certo que as recargas de areia, iniciadas em 2011, procuram minimizar os impactos da erosão, o que pode condicionar os resultados obtidos. Por outro lado, no que respeita às faixas de perigo, é certo que, com o recuar da costa, há uma tendência da frente urbana aproximar-se do nível de “perigo muito elevado”. Nesse sentido, a grande maioria do edificado situa-se na faixa de perigo moderado (211 edifícios), constatando-se que outra grande parte (193 edifícios) não se encontre ameaçado. De um total de 413 edifícios, apenas 1 encontra-se em perigo elevado. Mantendo-se esta tendência de recuo da costa e tendo por base o trabalho de campo efectuado, estima-se que os valores apresentados venham a alterar-se, isto é, tanto a população local, como o edificado tendem a aproximar-se do perigo máximo/elevado.

Characterization of molecular damage induced by UV photons and carbon ions on biomimetic heterostructures

The study of the effect of radiation on living tissues is a rather complex task to address mainly because they are made of a set of complex functional biological structures and interfaces. Particularly if one is looking for where damage is taking place in a first stage and what are the underlying reaction mechanisms. In this work a new approach is addressed to study the effect of radiation by making use of well identified molecular hetero-structures samples which mimic the biological environment. These were obtained by assembling onto a solid support deoxyribonucleic acid (DNA) and phospholipids together with a soft water-containing polyelectrolyte precursor in layered structures and by producing lipid layers at liquid/air interface with DNA as subphase. The effects of both ultraviolet (UV) radiation and carbon ions beams were systematically investigated in these heterostructures, namely damage on DNA by means vacuum ultraviolet (VUV), infrared (IR), X-Ray Photoelectron (XPS) and impedance spectroscopy. Experimental results revealed that UV affects furanose, PO2-, thymines, cytosines and adenines groups. The XPS spectrometry carried out on the samples allowed validate the VUV and IR results and to conclude that ionized phosphate groups, surrounded by the sodium counterions, congregate hydration water molecules which play a role of UV protection. The ac electrical conductivity measurements revealed that the DNA electrical conduction is arising from DNA chain electron hopping between base-pairs and phosphate groups, with the hopping distance equal to the distance between DNA base-pairs and is strongly dependent on UV radiation exposure, due loss of phosphate groups. Characterization of DNA samples exposed to a 4 keV C3+ ions beam revealed also carbon-oxygen bonds break, phosphate groups damage and formation of new species. Results from radiation induced damage carried out on biomimetic heterostructures having different compositions revealed that damage is dependent on sample composition, with respect to functional targeted groups and extent of damage. Conversely, LbL films of 1,2-dipalmitoyl-sn-Glycero-3-[Phospho-rac-(1-glycerol)] (Sodium Salt) (DPPG) liposomes, alternated with poly(allylamine hydrochloride) (PAH) revealed to be unaffected, even by prolonged UV irradiation exposure, in the absence of water molecules. However, DPPG molecules were damaged by the UV radiation in presence of water with cleavage of C-O, C=O and –PO2- bonds. Finally, the study of DNA interaction with the ionic lipids at liquid/air interfaces revealed that electrical charge of the lipid influences the interaction of phospholipid with DNA. In the presence of DNA in the subphase, the effects from UV irrladiation were seen to be smaller, which means that ionic products from biomolecules degradation stabilize the intact DPPG molecules. This mechanism may explain why UV irradiation does not cause immediate cell collapse, thus providing time for the cellular machinery to repair elements damaged by UV.

8-Phase Ring oscillator for modern receivers

The evolution of receiver architectures, built in modern CMOS technologies, allows the design of high efficient receivers. A key block in modern receivers is the oscillator. The main objective of this thesis is to design a very low power and low area 8-Phase Ring Oscillator for biomedical applications (ISM and WMTS bands). Oscillators with multiphase outputs and variable duty cycles are required. In this thesis we are focused in 12.5% and 50% duty-cycles approaches. The proposed circuit uses eight inverters in a ring structure, in order to generate the output duty cycle of 50%. The duty cycle of 1/8 is achieved through the combination of the longer duty cycle signals in pairs, using, for this purpose, NAND gates. Since the general application are not only the wireless communications context, as well as industrial, scientific and medical plans, the 8-Phase Oscillator is simulated to be wideband between 100 MHz and 1 GHz, and be able to operate in the ISM bands (447 MHz-930 MHz) and WMTS (600 MHz). The circuit prototype is designed in UMC 130 nm CMOS technology. The maximum value of current drawn from a DC power source of 1.2 V, at a maximum frequency of 930 MHz achieved, is 17.54 mA. After completion of the oscillator layout studied (occupied area is 165 μm x 83 μm). Measurement results confirm the expected operating range from the simulations, and therefore, that the oscillator fulfil effectively the goals initially proposed in order to be used as Local Oscillator in RF Modern Receivers.

Design and characterization of novel biopolymeric structure using biocompatible ionic liquids

The main objective of this thesis was the development of polymeric structures from the dissolution of FucoPol, a bacterial exopolysaccharide (EPS), in a biocompatible ionic liquid, choline acetate. The FucoPol was produced by the bacteria Enterobacter A47 using glycerol as carbon source at controlled temperature and pH (30ºC and 7, respectively). At the end of 3 days it was produced 7 g/L of FucoPol. The net yield of Fucopol in glycerol (YP/S) was 0.22 g/g and the maximum productivity 2.37 g/L.d This polymer was characterized about its composition in sugars and acyl groups (by High-Performance Liquid Chromatography - HPLC), containing fucose (35 % mol), galactose (21 % mol), glucose (29 % mol), rhamnose (3% mol) and glucuronic acid (12% mol) as well as acetate (14.28 % mol), pyruvate (2.15 % mol) and succinate (1.80 % mol). Its content of water and ash was 15% p/p and 2% p/p, respectively, and the chemical bonds (determined by Infrared Spectroscopy - FT-IR) are consistent to the literature reports. However, due to limitations in Differential Scanning Calorimetry (DSC) equipment it was not possible to determine the glass transition temperature. In turn, the ionic liquid showed the typical behavior of a Newtonian fluid, glass transition temperature (determined by DSC) -98.03ºC and density 1.1031 g/cm3. The study of chemical bonds by FT-IR showed that amount of water (8.80%) influenced the visualization of the bands predicted to in view of their chemical structure. After the dissolution of the FucoPol in the ionic liquid at different temperatures (50, 60, 80 and 100 ° C) it was promoted the removal of this by the phase inversion method using deionized water as a solvent, followed by drying in an oven at 70 ° C. The mixtures before and after the phase inversion method were characterized through the studies mentioned above. In order to explore possible application field’s biocompatibility assays and collage on balsa wood tests were performed. It was found that the process of washing with water by the phase inversion method was not totally effective in removing the biocompatible ionic liquid, since all FucoPol – IL mixtures still contained ionic liquid in their composition as can be seen by the DSC results and FT-IR. In addition, washing the mixtures with water significantly altered the composition of FucoPol. However, these mixtures, that developed a viscous behavior typical of a non-Newtonian fluid (shear-thinning), have the potential to be applied in the biomedical field as well as biological glues.

Light harvesting in solar cells using natural pigments from red fruits adsorbed to mesoporous TiO2

Nature has developed strategies to present us with a wide variety of colours, from the green of leaves to the bright colours seen in flowers. Anthocyanins are between these natural pigments that are responsible for the great diversity of colours seen in flowers and fruits. Anthocyanins have been used to sensitize titanium dioxide (TiO2) in Dye-Sensitized Solar Cells (DSSCs). DSSCs have become one of the most popular research topic in photovoltaic cells due to their low production costs when compared to other alternatives. DSSCs are inspired in what happens in nature during photosynthesis. A primary charge separation is achieved by means of a photoexcited dye capable of performing the electron injection into the conduction band of a wide band-gap semiconductor, usually TiO2. With this work we aimed to synthesize a novel mesoporous TiO2 structure as the semiconductor in order to increase the dye loading. We used natural occurring dyes such as anthocyanins and their synthetic flavylium relatives, as an alternative to the widely used metal complexes of Ru(II) which are expensive and are environmentally unsafe. This offers not only the chance to use safer dyes for DSSCs, but also to take profit of waste biological products, such as wine and olive oil production residues that are heavily loaded with anthocyanin dyes. We also performed a photodegradation study using TiO2 as the catalyst to degrade dye contaminants, such as those from the wine production waste, by photo-irradiation of the system in the visible region of the light spectrum. We were able to succeed in the synthesis of mesoporous TiO2 both powder and thin film, with a high capacity to load a large amount of dye. We proved the concept of photodegradation using TiO2 as catalyst. And finally, we show that wine production waste is a possible dye source to DSSCs application.