Nanostructuring silicon probes via electrodeposition: characterization of electrode coatings for acute in vivo neural recordings

Understanding how the brain works will require tools capable of measuring neuron elec-trical activity at a network scale. However, considerable progress is still necessary to reliably increase the number of neurons that are recorded and identified simultaneously with existing mi-croelectrode arrays. This project aims to evaluate how different materials can modify the effi-ciency of signal transfer from the neural tissue to the electrode. Therefore, various coating materials (gold, PEDOT, tungsten oxide and carbon nano-tubes) are characterized in terms of their underlying electrochemical processes and recording ef-ficacy. Iridium electrodes (177-706 μm2) are coated using galvanostatic deposition under different charge densities. By performing electrochemical impedance spectroscopy in phosphate buffered saline it is determined that the impedance modulus at 1 kHz depends on the coating material and decreased up to a maximum of two orders of magnitude for PEDOT (from 1 MΩ to 25 kΩ). The electrodes are furthermore characterized by cyclic voltammetry showing that charge storage capacity is im-proved by one order of magnitude reaching a maximum of 84.1 mC/cm2 for the PEDOT: gold nanoparticles composite (38 times the capacity of the pristine). Neural recording of spontaneous activity within the cortex was performed in anesthetized rodents to evaluate electrode coating performance.

Damage propagation in composite Materials meso-mechanical models

Composite materials have a complex behavior, which is difficult to predict under different types of loads. In the course of this dissertation a methodology was developed to predict failure and damage propagation of composite material specimens. This methodology uses finite element numerical models created with Ansys and Matlab softwares. The methodology is able to perform an incremental-iterative analysis, which increases, gradually, the load applied to the specimen. Several structural failure phenomena are considered, such as fiber and/or matrix failure, delamination or shear plasticity. Failure criteria based on element stresses were implemented and a procedure to reduce the stiffness of the failed elements was prepared. The material used in this dissertation consist of a spread tow carbon fabric with a 0°/90° arrangement and the main numerical model analyzed is a 26-plies specimen under compression loads. Numerical results were compared with the results of specimens tested experimentally, whose mechanical properties are unknown, knowing only the geometry of the specimen. The material properties of the numerical model were adjusted in the course of this dissertation, in order to find the lowest difference between the numerical and experimental results with an error lower than 5% (it was performed the numerical model identification based on the experimental results).

Estudo da influência do material inorgânico na formação de H2S e HCl durante a co-gasificação de CDR com carvão

O objectivo principal deste trabalho relaciona-se com a compreensão dos mecanismos de formação de H2S e HCl durante a co-gasificação de C.D.R com carvão. A presença de material inorgânico nas cinzas dos combustíveis utilizados poderá ter alguma influência na formação e subsequentes reacções de H2S e HCl, tornando-se importante compreender qual a extensão da influência destes materiais na formação destas espécies, encaradas como contaminantes do gás produzido. A utilização de misturas de C.D.R. com carvão em gasificação poderá contribuir para a redução das quantidades de resíduos depositadas em aterro. Sendo a gasificação um processo menos poluente do que a incineração, a gasificação destes materiais poderá traduzir-se num menor impacto ambiental. Os C.D.R. são materiais heterogéneos e portanto as quantidades de S, Cl e material inorgânico poderão variar tornando relevante o estudo de potenciais sinergias entre os C.D.R. e o carvão com o objectivo de 1) minimizar a emissão de poluentes gasosos, 2) minimizar a quantidade de cinza produzida e 3) aproveitar o material inorgânico, que pode desempenhar actividade catalítica conduzindo à redução da formação de H2S e HCl. Com este estudo foi determinada uma aparente relação linear entre os teores de enxofre nos combustíveis e a formação de H2S, sendo que no entanto a forma sob a qual o enxofre se encontra nos combustíveis poderá desempenhar um importante papel na conversão do enxofre em H2S. No caso do HCl, a referida relação não pareceu ser tão clara. Foi igualmente determinado que maiores temperaturas de operação promovem a formação de H2S, ao mesmo tempo que reduzem a formação de HCl, e que enquanto o aumento da quantidade de oxigénio poderá conduzir à redução da formação de H2S, não terá impacto significativo na formação de HCl. No que diz respeito aos metais foi verificado que Ca, Fe e Zn terão um papel importante na redução da formação de H2S e HCl, enquanto que K e Na terão apenas influência na formação de HCl e o Al e a Si, não afectaram nem a formação de H2S nem a de HCl.

Estudo da influência do material de enchimento na remoção de matéria orgânica, azoto e sólidos em leitos de macrófitas do tipo ESSH

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Sanitária

Um segredo bem guardado: Leques mandarim – caracterização material e conservação

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Conservação e Restauro

Design of New Materials for Passive Vibration Control

The objective of this contribution is to extend the models of cellular/composite material design to nonlinear material behaviour and apply them for design of materials for passive vibration control. As a first step a computational tool allowing determination of optimised one-dimensional isolator behaviour was developed. This model can serve as a representation for idealised macroscopic behaviour. Optimal isolator behaviour to a given set of loads is obtained by generic probabilistic metaalgorithm, simulated annealing. Cost functional involves minimization of maximum response amplitude in a set of predefined time intervals and maximization of total energy absorbed in the first loop. Dependence of the global optimum on several combinations of leading parameters of the simulated annealing procedure, like neighbourhood definition and annealing schedule, is also studied and analyzed. Obtained results facilitate the design of elastomeric cellular materials with improved behaviour in terms of dynamic stiffness for passive vibration control.

Post-processing Techniques in Free Boundary Flows during Liquid Composite Moulding Processes

Post-processing a finite element solution is a well-known technique, which consists in a recalculation of the originally obtained quantities such that the rate of convergence increases without the need for expensive remeshing techniques. Postprocessing is especially effective in problems where better accuracy is required for derivatives of nodal variables in regions where Dirichlet essential boundary condition is imposed strongly. Consequently such an approach can be exceptionally good in modelling of resin infiltration under quasi steady-state assumption by remeshing techniques and with explicit time integration, because only the free-front normal velocities are necessary to advance the resin front to the next position. The new contribution is the post-processing analysis and implementation of the freeboundary velocities of mesolevel infiltration analysis. Such implementation ensures better accuracy on even coarser meshes, which in consequence reduces the computational time also by the possibility of employing larger time steps.

Numerical Method to Predict Void Formation during The Liquid Composite Molding Process

Void formation during the injection phase of the liquid composite molding process can be explained as a consequence of the non-uniformity of the flow front progression. This is due to the dual porosity within the fiber perform (spacing between the fiber tows is much larger than between the fibers within in a tow) and therefore the best explanation can be provided by a mesolevel analysis, where the characteristic dimension is given by the fiber tow diameter of the order of millimeters. In mesolevel analysis, liquid impregnation along two different scales; inside fiber tows and within the open spaces between the fiber tows must be considered and the coupling between the flow regimes must be addressed. In such cases, it is extremely important to account correctly for the surface tension effects, which can be modeled as capillary pressure applied at the flow front. Numerical implementation of such boundary conditions leads to illposing of the problem, in terms of the weak classical as well as stabilized formulation. As a consequence, there is an error in mass conservation accumulated especially along the free flow front. A numerical procedure was formulated and is implemented in an existing Free Boundary Program to reduce this error significantly.

Preliminary study on the production of functionally graded materials by friction stir processing

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Mecânica

A conservação material e documental da obra “Instalação191093,parte1” de Francisco Rocha

Dissertação apresentada na Faculdade de Ciências e Tecnologia para obtenção do grau de Mestre em Conservação e Restauro

How composite indicators of innovation can influence technology policy decision?

Based on the report for Project III of the PhD programme on Technology Assessment and prepared for the Winter School that took place at Universidade Nova de Lisboa, Caparica Campus on the 6th and 7th of December 2010.

Design of New Materials for Passive Vibration Control

The aim of this contribution is to extend the techniques of composite materials design to non-linear material behaviour and apply it for design of new materials for passive vibration control. As a first step a computational tool allowing determination of macroscopic optimized one-dimensional isolator behaviour was developed. Voigt, Maxwell, standard and more complex material models can be implemented. Objective function considers minimization of the initial reaction and/or displacement peak as well as minimization of the steady-state amplitude of reaction and/or displacement. The complex stiffness approach is used to formulate the governing equations in an efficient way. Material stiffness parameters are assumed as non-linear functions of the displacement. The numerical solution is performed in the complex space. The steady-state solution in the complex space is obtained by an iterative process based on the shooting method which imposes the conditions of periodicity with respect to the known value of the period. Extension of the shooting method to the complex space is presented and verified. Non-linear behaviour of material parameters is then optimized by generic probabilistic meta-algorithm, simulated annealing. Dependence of the global optimum on several combinations of leading parameters of the simulated annealing procedure, like neighbourhood definition and annealing schedule, is also studied and analyzed. Procedure is programmed in MATLAB environment.

Caracterização material e conservação e restauro de um painel de azulejos do séc. XVII do Ecomuseu do Seixal, Portugal

Dissertação para obtenção do Grau de Mestre em Conservação e Restauro, Especialização em Cerâmica e Vidro

Cravo de Pascal Taskin (1782): caracterização material da policromia exterior

Dissertação para obtenção do Grau de Mestre em Conservação e Restauro, Especialização em Ciências da Conservação

A música como expressão e cognição: a propositósito do conceito de "crítica imanente do material" em adorno

Numa recensão às conferências sobre "Metafísica - Conceitos e Problemas" {Metaphysik. Begriffe und Probleme), proferidas por Adorno, na Universidade de Frankfurt, no segundo semestre de 1965 e publicadas postumamente, o filósofo dinamarquês Stâle R. S. Finke (1999) analisa os "esforços" de Adorno por "recuperar a concepção da experiência metafísica". Uma tal recuperação teria de ser compreendida num quadro de pensamento que é o da "dialéctica negativa", por sua vez tributária dos padrões kantianos de "consciência conceptual e autonomia moral" que Adorno articula naquilo a que Finke chama o "projecto" ou o "ideal de liberdade expressiva". O conceito de experiência metafísica, formulado nas referidas conferências, seria, assim, da maior importância para Adorno, pois que nele se daria expressão ao objectivo da "dialéctica negativa" (a Negative Dialektik foi publicada no ano seguinte, 1966): "a invocação do não-idêntico como condição de experiência e de expressão". "Relacionada intrinsecamente" com o "donnnio da experiência possível", histórica e cultural, isto é, com tudo aquilo que constrange a autonomia (por um lado permitindo, por outro lado limitando as possibilidades do eu), a concepção da experiência metafísica em Adorno convoca essas possibilidades do eu como inalcançadas