Análise não linear do comportamento dinâmico de passadiços pedonais pré-fabricados

Os terramotos têm sido considerados uma das forças mais destrutivas e violentas da natureza, causando grandes tragédias e perdas económicas significativas. O objetivo principal do presente estudo é avaliar o comportamento global e local de três pontes pedonais, pré-fabricadas, durante a ação sísmica regulamentar. Através destas análises, pretende-se avaliar o risco de colapso das estruturas por “descalçamento” do tabuleiro e, caso necessário, propor soluções para evitar este fenómeno e melhorar o desempenho sísmico dos passadiços. No domínio de pontes, o “descalçamento dos apoios” é um tipo de rotura que pode ocorrer em estruturas com tramos simplesmente apoiados, onde os problemas surgem geralmente na interface de ligação tabuleiro-pilar, podendo conduzir ao derrubamento do primeiro. Este tipo de ligação é geralmente constituído por um conjunto de varões de aço – ferrolhos, chumbados verticalmente ao capitel do pilar e que atravessam placas de neoprene, ficando instalados no negativo das vigas. A selagem dos varões é normalmente realizada com argamassa de alta resistência. Os problemas que surgem neste tipo de ligação estão associados, a maior parte das vezes, à falta de manutenção e ao insuficiente comprimento de entrega do tabuleiro na zona dos aparelhos de apoio. A simulação do comportamento da estrutura durante as várias fases construtivas e aplicação de cargas, até ao colapso total, implica a utilização de uma ferramenta adequada. A modelação numérica foi efetuada com recurso ao programa de cálculo não-linear de estruturas Extreme Loading for Structures, baseado no Método dos Elementos Aplicados. O método considera os efeitos da não-linearidade física e geométrica, permitindo analisar o comportamento das estruturas durante a fase elástica e inelástica, passando pela cedência das armaduras, abertura e propagação de fendas até à separação dos elementos. Com base neste trabalho, foi possível verificar alterações significativas na resposta sísmica da estrutura, nomeadamente devido à eventual degradação dos ferrolhos.

Diffusional kurtosis imaging using a fast heuristic constrained linear least squares algorithm: a plugin for OsiriX

Diffusion Kurtosis Imaging (DKI) is a fairly new magnetic resonance imag-ing (MRI) technique that tackles the non-gaussian motion of water in biological tissues by taking into account the restrictions imposed by tissue microstructure, which are not considered in Diffusion Tensor Imaging (DTI), where the water diffusion is considered purely gaussian. As a result DKI provides more accurate information on biological structures and is able to detect important abnormalities which are not visible in standard DTI analysis. This work regards the development of a tool for DKI computation to be implemented as an OsiriX plugin. Thus, as OsiriX runs under Mac OS X, the pro-gram is written in Objective-C and also makes use of Apple’s Cocoa framework. The whole program is developed in the Xcode integrated development environ-ment (IDE). The plugin implements a fast heuristic constrained linear least squares al-gorithm (CLLS-H) for estimating the diffusion and kurtosis tensors, and offers the user the possibility to choose which maps are to be generated for not only standard DTI quantities such as Mean Diffusion (MD), Radial Diffusion (RD), Axial Diffusion (AD) and Fractional Anisotropy (FA), but also DKI metrics, Mean Kurtosis (MK), Radial Kurtosis (RK) and Axial Kurtosis (AK).The plugin was subjected to both a qualitative and a semi-quantitative analysis which yielded convincing results. A more accurate validation pro-cess is still being developed, after which, and with some few minor adjust-ments the plugin shall become a valid option for DKI computation

Hydric behavior of earth materials and the effects of their stabilization with cement or lime: study on repair mortars for historical rammed earth structures

Earthen building materials bear interesting environmental advantages and are the most appropriate to conserve historical earth constructions. To improve mechanical properties, these materials are often stabilized with cement or lime, but the impact of the stabilizers on the water transport properties, which are also critical, has been very rarely evaluated. We have tested four earth-based repair mortars applied on three distinct and representative rammed earth surfaces. Three mortars are based on earth collected from rammed earth buildings in south of Portugal and the fourth mortar is based on a commercial clayish earth. The main objective of the work was over the commercial earth mortar, applied stabilized and not stabilized on the three rammed earth surfaces to repair, to assess the influence of the stabilizers. The other three earth mortars (not stabilized) were applied on each type of rammed earth, representing the repair only made with local materials. The four unstabilized earth materials depicted nonlinear dependence on t1/2 during capillary suction. This behaviour was probably due to clay swelling. Stabilization with any of the four tested binders enabled the linear dependence of t1/2 expected from Washburn's equation, probably because the swelling did not take place in this case. However, the stabilizers also increased significantly the capillary suction and the capillary porosity of the materials. This means that, in addition to increasing the carbon footprint, stabilizers like cement and lime have functional disadvantages that discourage its use in repair mortars for raw earth construction.

An introduction to the fractional continuous-time linear systems

A brief introduction to the fractional continuous-time linear systems is presented. It will be done without needing a deep study of the fractional derivatives. We will show that the computation of the impulse and step responses is very similar to the classic. The main difference lies in the substitution of the exponential by the Mittag-Leffler function. We will present also the main formulae defining the fractional derivatives.

Modelação das Propriedades mecânicas de juntas soldadas por fricção linear

Dissertação apresentada à Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do Grau de Mestre em Engenharia Mecânica

Development of biocompatible and “smart” porous structures using CO2-assisted processes

Dissertação apresentada para a obtenção do grau de Doutor em Engenharia Química, especialidade Engenharia da Reacção Química, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Estimation and hypothesis testing in mixed linear models

Dissertação apresentada para obtenção do Grau de Doutor em Matemática, Estatística, pela Universidade Nova de Lisboa, faculdade de Ciências e Tecnologia

Segmentation of striatal brain structures from high resolution pet images

Dissertation presented at the Faculty of Science and Technology of the New University of Lisbon in fulfillment of the requirements for the Masters degree in Electrical Engineering and Computers

An introduction to the fractional continuous- time linear systems: the 21st century systems

IEEE CIRCUITS AND SYSTEMS MAGAZINE, Third Quarter

New quasi-orthogonal BCH-derived sequences for CDMA applications

European Transactions on Telecommunications, vol. 18

On the initial conditions in continuous-time fractional linear systems

Signal Processing, Vol. 83, nº 11

Fractional discrete-time signal processing: scale conversion and linear prediction

Nonlinear Dynamics, Vol. 29

Introduction to fractional linear systems. Part 1 : continuous-time case

IEE Proceedings - Vision, Image, and Signal Processing, Vol. 147, nº 1

Introduction to fractional linear systems. Part 2: discrete-time case

IEE Proceedings - Vision, Image, and Signal Processing, Vol. 147, nº 1