Analysis and design of sinusoidal quadrature RC-oscillators

Modern telecommunication equipment requires components that operate in many different frequency bands and support multiple communication standards, to cope with the growing demand for higher data rate. Also, a growing number of standards are adopting the use of spectrum efficient digital modulations, such as quadrature amplitude modulation (QAM) and orthogonal frequency division multiplexing (OFDM). These modulation schemes require accurate quadrature oscillators, which makes the quadrature oscillator a key block in modern radio frequency (RF) transceivers. The wide tuning range characteristics of inductorless quadrature oscillators make them natural candidates, despite their higher phase noise, in comparison with LC-oscillators. This thesis presents a detailed study of inductorless sinusoidal quadrature oscillators. Three quadrature oscillators are investigated: the active coupling RC-oscillator, the novel capacitive coupling RCoscillator, and the two-integrator oscillator. The thesis includes a detailed analysis of the Van der Pol oscillator (VDPO). This is used as a base model oscillator for the analysis of the coupled oscillators. Hence, the three oscillators are approximated by the VDPO. From the nonlinear Van der Pol equations, the oscillators’ key parameters are obtained. It is analysed first the case without component mismatches and then the case with mismatches. The research is focused on determining the impact of the components’ mismatches on the oscillator key parameters: frequency, amplitude-, and quadrature-errors. Furthermore, the minimization of the errors by adjusting the circuit parameters is addressed. A novel quadrature RC-oscillator using capacitive coupling is proposed. The advantages of using the capacitive coupling are that it is noiseless, requires a small area, and has low power dissipation. The equations of the oscillation amplitude, frequency, quadrature-error, and amplitude mismatch are derived. The theoretical results are confirmed by simulation and by measurement of two prototypes fabricated in 130 nm standard complementary metal-oxide-semiconductor (CMOS) technology. The measurements reveal that the power increase due to the coupling is marginal, leading to a figure-of-merit of -154.8 dBc/Hz. These results are consistent with the noiseless feature of this coupling and are comparable to those of the best state-of-the-art RC-oscillators, in the GHz range, but with the lowest power consumption (about 9 mW). The results for the three oscillators show that the amplitude- and the quadrature-errors are proportional to the component mismatches and inversely proportional to the coupling strength. Thus, increasing the coupling strength decreases both the amplitude- and quadrature-errors. With proper coupling strength, a quadrature error below 1° and amplitude imbalance below 1% are obtained. Furthermore, the simulations show that increasing the coupling strength reduces the phase noise. Hence, there is no trade-off between phase noise and quadrature error. In the twointegrator oscillator study, it was found that the quadrature error can be eliminated by adjusting the transconductances to compensate the capacitance mismatch. However, to obtain outputs in perfect quadrature one must allow some amplitude error.

A systematic methodology to analyse the performance and design configurations of business interoperability in cooperative industrial networks

This thesis proposes a methodology for modelling business interoperability in a context of cooperative industrial networks. The purpose is to develop a methodology that enables the design of cooperative industrial network platforms that are able to deliver business interoperability and the analysis of its impact on the performance of these platforms. To achieve the proposed objective, two modelling tools have been employed: the Axiomatic Design Theory for the design of interoperable platforms; and Agent-Based Simulation for the analysis of the impact of business interoperability. The sequence of the application of the two modelling tools depends on the scenario under analysis, i.e. whether the cooperative industrial network platform exists or not. If the cooperative industrial network platform does not exist, the methodology suggests first the application of the Axiomatic Design Theory to design different configurations of interoperable cooperative industrial network platforms, and then the use of Agent-Based Simulation to analyse or predict the business interoperability and operational performance of the designed configurations. Otherwise, one should start by analysing the performance of the existing platform and based on the achieved results, decide whether it is necessary to redesign it or not. If the redesign is needed, simulation is once again used to predict the performance of the redesigned platform. To explain how those two modelling tools can be applied in practice, a theoretical modelling framework, a theoretical Axiomatic Design model and a theoretical Agent-Based Simulation model are proposed. To demonstrate the applicability of the proposed methodology and/or to validate the proposed theoretical models, a case study regarding a Portuguese Reverse Logistics cooperative network (Valorpneu network) and a case study regarding a Portuguese construction project (Dam Baixo Sabor network) are presented. The findings of the application of the proposed methodology to these two case studies suggest that indeed the Axiomatic Design Theory can effectively contribute in the design of interoperable cooperative industrial network platforms and that Agent-Based Simulation provides an effective set of tools for analysing the impact of business interoperability on the performance of those platforms. However, these conclusions cannot be generalised as only two case studies have been carried out. In terms of relevance to theory, this is the first time that the network effect is addressed in the analysis of the impact of business interoperability on the performance of networked companies and also the first time that a holistic approach is proposed to design interoperable cooperative industrial network platforms. Regarding the practical implications, the proposed methodology is intended to provide industrial managers a management tool that can guide them easily, and in practical and systematic way, in the design of configurations of interoperable cooperative industrial network platforms and/or in the analysis of the impact of business interoperability on the performance of their companies and the networks where their companies operate.

The names of things: terminology and the practice of art history

This paper aims to explore the ways in which standard art history terminology shapes the practice of art history by conditioning the interpretation of specific works of art and, in certain cases, the definition of a research subject (especially where questions of genre and periodization are concerned). Taking as a case study a painting by Georges de La Tour, the Peasant Couple Eating, I will argue that terms such as realism, realistic, naturalistic etc. used for its description and/or interpretation, far from constituting objective stylistic characterizations, shape our perception of the work in question. Bringing the question of social class to the center of the discourse on realism, I propose to show how the social divide between the painter and his subject matter (in this case, the peasants) is internalized in the painting’s style and meaning, and how it is fundamental for the understanding of its intentionality and function.

The 1st ISA forum of sociology on the “Sociological Research and Public Debate”

1st ISA Forum report

Is ambient intelligence a truly human-centric paradigm in industry? Current research and application scenario

Based on the paper presented at the International Conference “Autonomous Systems: inter-relations of technical and societal issues”, organized by IET with the support of the Portuguese-German collaboration project on “Technology Assessment of Autonomous Robotics” (DAAD/CRUP) at FCT-UNL, Biblioteca da UNL, Campus de Caparica on 5-6 November 2009.

Research and development expenditure in the business sector as indicator of knowledge economy: the Portuguese experience

The objective of the paper is to help to understand recent changes in the structure of R&D activities, by analyzing data on the expenditure of the business sector in research and development (R&D). The results are framed in an international context, through comparison with indicators from the most developed countries, divided by technological intensity and economic activity. The study reveals that the indicators of Portuguese R&D expenditure in the business sector are closely linked both to fiscal policy and to high foreign direct investment in knowledge-intensive industries. It also links these indicators to phenomena such as the abundance of skilled labor in pharmaceutical industries and the government intervention in some sectors of the economy (namely health and rail transportation).

Spiteful Strategies. The ontogeny and the practice of spite in human interaction: an experimental game theory approach and empirical applications

As estratégias de malevolência implicam que um indivíduo pague um custo para infligir um custo superior a um oponente. Como um dos comportamentos fundamentais da sociobiologia, a malevolência tem recebido menos atenção que os seus pares o egoísmo e a cooperação. Contudo, foi estabelecido que a malevolência é uma estratégia viável em populações pequenas quando usada contra indivíduos negativamente geneticamente relacionados pois este comportamento pode i) ser eliminado naturalmente, ou ii) manter-se em equilíbrio com estratégias cooperativas devido à disponibilidade da parte de indivíduos malevolentes de pagar um custo para punir. Esta tese propõe compreender se a propensão para a malevolência nos humanos é inerente ou se esta se desenvolve com a idade. Para esse efeito, considerei duas experiências de teoria de jogos em crianças em ambiente escolar com idades entre os 6 e os 22 anos. A primeira, um jogo 2x2 foi testada com duas variantes: 1) um prémio foi atribuído a ambos os jogadores, proporcionalmente aos pontos acumulados; 2), um prémio foi atribuído ao jogador com mais pontos. O jogo foi desenhado com o intuito de causar o seguinte dilema a cada jogador: i) maximizar o seu ganho e arriscar ter menos pontos que o adversário; ou ii) decidir não maximizar o seu ganho, garantindo que este não era inferior ao do seu adversário. A segunda experiência consistia num jogo do ditador com duas opções: uma escolha egoísta/altruísta (A), onde o ditador recebia mais ganho, mas o seu recipiente recebia mais que ele e uma escolha malevolente (B) que oferecia menos ganhos ao ditador que a A mas mais ganhos que o recipiente. O dilema era que se as crianças se comportassem de maneira egoísta, obtinham mais ganho para si, ao mesmo tempo que aumentavam o ganho do seu colega. Se fossem malevolentes, então prefeririam ter mais ganho que o seu colega ao mesmo tempo que tinham menos para eles próprios. As experiências foram efetuadas em escolas de duas áreas distintas de Portugal (continente e Açores) para perceber se as preferências malevolentes aumentavam ou diminuíam com a idade. Os resultados na primeira experiência sugerem que (1) os alunos compreenderam a primeira variante como um jogo de coordenação e comportaram-se como maximizadores, copiando as jogadas anteriores dos seus adversários; (2) que os alunos repetentes se comportaram preferencialmente como malevolentes, mais frequentemente que como maximizadores, com especial ênfase para os alunos de 14 anos; (3) maioria dos alunos comportou-se reciprocamente desde os 12 até aos 16 anos de idade, após os quais começaram a desenvolver uma maior tolerância às escolhas dos seus parceiros. Os resultados da segunda experiência sugerem que (1) as estratégias egoístas eram prevalentes até aos 6 anos de idade, (2) as tendências altruístas emergiram até aos 8 anos de idade e (3) as estratégias de malevolência começaram a emergir a partir dos 8 anos de idade. Estes resultados complementam a literatura relativamente escassa sobre malevolência e sugerem que este comportamento está intimamente ligado a preferências de consideração sobre os outros, o paroquialismo e os estágios de desenvolvimento das crianças.************************************************************Spite is defined as an act that causes loss of payoff to an opponent at a cost to the actor. As one of the four fundamental behaviours in sociobiology, it has received far less attention than its counterparts selfishness and cooperation. It has however been established as a viable strategy in small populations when used against negatively related individuals. Because of this, spite can either i) disappear or ii) remain at equilibrium with cooperative strategies due to the willingness of spiteful individuals to pay a cost in order to punish. This thesis sets out to understand whether propensity for spiteful behaviour is inherent or if it develops with age. For that effect, two game-theoretical experiments were performed with schoolboys and schoolgirls aged 6 to 22. The first, a 2 x 2 game, was tested in two variants: 1) a prize was awarded to both players, proportional to accumulated points; 2), a prize was given to the player with most points. Each player faced the following dilemma: i) to maximise pay-off risking a lower pay-off than the opponent; or ii) not to maximise pay-off in order to cut down the opponent below their own. The second game was a dictator experiment with two choices, (A) a selfish/altruistic choice affording more payoff to the donor than B, but more to the recipient than to the donor, and (B) a spiteful choice that afforded less payoff to the donor than A, but even lower payoff to the recipient. The dilemma here was that if subjects behaved selfishly, they obtained more payoff for themselves, while at the same time increasing their opponent payoff. If they were spiteful, they would rather have more payoff than their colleague, at the cost of less for themselves. Experiments were run in schools in two different areas in Portugal (mainland and Azores) to understand whether spiteful preferences varied with age. Results in the first experiment suggested that (1) students understood the first variant as a coordination game and engaged in maximising behaviour by copying their opponent’s plays; (2) repeating students preferentially engaged in spiteful behaviour more often than maximising behaviour, with special emphasis on 14 year-olds; (3) most students engaged in reciprocal behaviour from ages 12 to 16, as they began developing higher tolerance for their opponent choices. Results for the second experiment suggested that (1) selfish strategies were prevalent until the age of 6, (2) altruistic tendencies emerged since then, and (3) spiteful strategies began being chosen more often by 8 year-olds. These results add to the relatively scarce body of literature on spite and suggest that this type of behaviour is closely tied with other-regarding preferences, parochialism and the children’s stages of development.

Men's grooming in Germany: A consumer research and discussion of current consumer attitudes

The objective of this dissertation was to explore the German men’s grooming market and to discuss the usage and purchase behavior of young male adults. After a brief market analysis, this dissertation evaluates the results of qualitative and quantitative research. The conducted research explored the consumer’s reasoning for and attitude towards personal grooming, and their attitude towards product attributes and the aging process. The dissertation concludes that men attach high value to personal grooming but only to the extent that their personal need is satisfied. As the male involvement in MG is highly dependent on each consumer’s individual needs, the market requires a careful segmentation.

Responsible research and innovation: a global perspective

Based on the paper presented at the Doctorate Conference on Technologogy Assessment in July 2013 at the University Nova Lisboa, Caparica campus

Genome-scale metabolic network reconstruction of Polaromonas sp. strain JS666: analysis of cDCE degradation rates and design of experiments for bioremediation improvement

Release of chloroethene compounds into the environment often results in groundwater contamination, which puts people at risk of exposure by drinking contaminated water. cDCE (cis-1,2-dichloroethene) accumulation on subsurface environments is a common environmental problem due to stagnation and partial degradation of other precursor chloroethene species. Polaromonas sp. strain JS666 apparently requires no exotic growth factors to be used as a bioaugmentation agent for aerobic cDCE degradation. Although being the only suitable microorganism found capable of such, further studies are needed for improving the intrinsic bioremediation rates and fully comprehend the metabolic processes involved. In order to do so, a metabolic model, iJS666, was reconstructed from genome annotation and available bibliographic data. FVA (Flux Variability Analysis) and FBA (Flux Balance Analysis) techniques were used to satisfactory validate the predictive capabilities of the iJS666 model. The iJS666 model was able to predict biomass growth for different previously tested conditions, allowed to design key experiments which should be done for further model improvement and, also, produced viable predictions for the use of biostimulant metabolites in the cDCE biodegradation.

Responsible research and innovation: a global perspective

Based on the paper presented at the Doctorate Conference on Technologogy Assessment in July 2013 at the University Nova Lisboa, Caparica campus

Optimisation and design of post-tensioning anchorage corner blisters in concrete box girder bidges

The design of anchorage blisters of internal continuity post-tensioning tendons of bridges built by the cantilever method, presents some peculiarities, not only because they are intermediate anchorages but also because these anchorages are located in blisters, so the prestressing force has to be transferred from the blister the bottom slab and web of the girder. The high density of steel reinforcement in anchorage blisters is the most common reason for problems with concrete cast in situ, resulting in zones with low concrete compacity, leading to concrete crushing failures under the anchor plates. A solution may involve improving the concrete compression and tensile strength. To meet these requirements a high-performance fibre reinforced self-compacting mix- ture (HPFRC) was used in anchorage corner blisters of post-tensioning tendons, reducing the concrete cross-section and decreasing the reinforcement needed. To assess the ultimate capacity and the adequate serviceability of the local anchorage zone after reducing the minimum concrete cross-section and the confining reinforcement, specified by the anchorage device supplier for the particular tendon, load transfer tests were performed. To investigate the behaviour of anchorage blisters regarding the transmission of stresses to the web and the bottom slab of the girder, and the feasibility of using high performance concrete only in the blister, two half scale models of the inferior corner of a box girder existing bridge were studied: a reference specimen of ordinary reinforced concrete and a HPFRC blister specimen. The design of the reinforcement was based in the tensile forces obtained on strut-and-tie models. An experimental program was carried out to assess the models used in design and to study the feasibility of using high performance concrete only in the blister, either with casting in situ, or with precast solutions. A non-linear finite element analysis of the tested specimens was also performed and the results compared.

Electro-Optical/Infrared sensor turret integration on an aircraft - structural im-pact on LOCKHEED MARTIN C-130H and design methodology

The growing need to patrol and survey large maritime and terrestrial areas increased the need to integrate external sensors on aircraft in order to accomplish those patrols at increasingly higher altitudes, longer range and not depending upon vehicle type. The main focus of this work is to elaborate a practical, simple, effective and efficient methodology for the aircraft modification procedure resulting from the integration of an Elec-tro-Optical/Infra-Red (EO/IR) turret through a support structure. The importance of the devel-opment of a good methodology relies on the correct management of project variables as time, available resources and project complexity. The key is to deliver a proper tool for a project de-sign team that will be used to create a solution that fulfils all technical, non-technical and certi-fication requirements present in this field of transportation. The created methodology is inde-pendent of two main inputs: sensor model and aircraft model definition, and therefore it is in-tended to deliver the results for different projects besides the one that was presented in this work as a case study. This particular case study presents the development of a structure support for FLIR STAR SAPHIRE III turret integration on the front lower fuselage bulkhead (radome) of the LOCKHEED MARTIN C-130 H. Development of the case study focuses on the study of local structural analysis through the use of Finite Element Method (FEM). Development of this Dissertation resulted in a cooperation between Faculty of Science and Technology - Universidade Nova de Lisboa and the company OGMA - Indústria Aeronáutica de Portugal