Towards printed carbon nanotube transistors on paper substrates

This thesis reports the work performed in the optimization of deposition parameters of Multi – Walled Carbon Nanotubes (MWCNT) targeting the development of a Field Effect Transistors (FET) on paper substrates. The CNTs were dispersed in a water solution with sodium dodecyl sulphate (SDS) through ultrasonication, ultrasonic bath and a centrifugation to remove the supernatant and have a homogeneous solution. Several deposition tests were performed using different types of CNTs, dis-persants, papers substrates and deposition techniques, such as spray coating and inkjet printing. The characterization of CNTs was made by Scanning Electron Microscopy (SEM) and Hall Effect. The most suitable CNT coatings able to be used as semiconductor in FETs were deposited by spray coat-ing on a paper substrate with hydrophilic nanoporous surface (FS2) at 100 ºC, 4 bar, 10 cm height, 5 second of deposition time and 90 seconds of drying between steps (4 layers of CNTs were deposited). Planar electrolyte gated FETs were produced with these layers using gold-nickel gate, source and drain electrodes. Despite the small current modulation (Ion/Ioff ratio of 1.8) one of these devices have p-type conduction with a field effect mobility of 1.07 cm2/V.s.

Molecular simulation of gas adsorption equilibria in nanoporous materials

This work is divided into two distinct parts. The first part consists of the study of the metal organic framework UiO-66Zr, where the aim was to determine the force field that best describes the adsorption equilibrium properties of two different gases, methane and carbon dioxide. The other part of the work focuses on the study of the single wall carbon nanotube topology for ethane adsorption; the aim was to simplify as much as possible the solid-fluid force field model to increase the computational efficiency of the Monte Carlo simulations. The choice of both adsorbents relies on their potential use in adsorption processes, such as the capture and storage of carbon dioxide, natural gas storage, separation of components of biogas, and olefin/paraffin separations. The adsorption studies on the two porous materials were performed by molecular simulation using the grand canonical Monte Carlo (μ,V,T) method, over the temperature range of 298-343 K and pressure range 0.06-70 bar. The calibration curves of pressure and density as a function of chemical potential and temperature for the three adsorbates under study, were obtained Monte Carlo simulation in the canonical ensemble (N,V,T); polynomial fit and interpolation of the obtained data allowed to determine the pressure and gas density at any chemical potential. The adsorption equilibria of methane and carbon dioxide in UiO-66Zr were simulated and compared with the experimental data obtained by Jasmina H. Cavka et al. The results show that the best force field for both gases is a chargeless united-atom force field based on the TraPPE model. Using this validated force field it was possible to estimate the isosteric heats of adsorption and the Henry constants. In the Grand-Canonical Monte Carlo simulations of carbon nanotubes, we conclude that the fastest type of run is obtained with a force field that approximates the nanotube as a smooth cylinder; this approximation gives execution times that are 1.6 times faster than the typical atomistic runs.

Desenvolvimento de um sensor para detecção de nano e micro concentrações de deltametrina

Dissertação para obtenção do Grau de Mestre em Engenharia Física

Writing/erasing 3D micro and nano wrinkles in flexible elastomers for volatile organic compounds sensor

Micro/nano wrinkled patterns on cross-linked urethane/urea polymeric flexible free standing films with two soft segments, polypropylene oxide and polybutadiene, can be induced by UV-irradiation. The ability to write/erase these 3D structures, in a controlled manner, is the main focus of this work. The imprinting of the wrinkled structures was accomplished by swelling in an appropriate solvent followed by drying the membranes after the cross-linking process and UV irradiation. The surface tailoring of the elastomeric membranes was imaged by optical microscopy, scanning electronic microscopy and by atomic force microscopy. To erase the wrinkled structures the elastomers were swollen. The swelling as well as the sol/gel fraction and the UV radiation were tuned in order to control the wrinkles characteristics. It was found that the wrinkles wavelength, in the order of microns (1±0,25μm), was stamped by the UV radiation intensity and exposure time while the wrinkles' amplitude, in the order of nanometers (150-450 nm), was highly dependent on the swelling and sol/gel fraction. A prototype for volatile organic compounds detection was developed taking advantage of the unique 3D micro/nano wrinkles features.

Imunobiossensores capacitivos interdigitais com camadas sensíveis micro e nano-estruturadas

Dissertação para obtenção do Grau de Mestre em Biotecnologia

Desenvolvimento de um sensor de ibuprofeno em meio aquoso

A proteção dos recursos hídricos tem uma enorme importância ecológica, sendo a água um recurso indispensável à Vida e fundamental para o bem-estar de uma sociedade. Para isso, muitos dos poluentes que afetam a qualidade deste recurso natural são detetados e eliminados nas estações de tratamento de águas residuais. Porém, o impacto dos Produtos Farmacêuticos e de Cuidado Pessoal (PPCPs), usados à escala global, carece ainda da atenção necessária, dado que os meios técnicos atualmente disponíveis para detetar estes produtos são dispendiosos ou insuficientes. Dentro daquela classe de produtos, destaca-se o Ibuprofeno, uma vez que este composto, sendo lipossolúvel, tem a capacidade para se acumular nas gorduras dos seres vivos e, por conseguinte, persistir no meio-ambiente com efeitos nocivos. Para além desse facto, por diferentes vias de reação, o Ibuprofeno tem potencial para gerar produtos de carácter semelhante. No entanto, pouco esforços têm sido feitos no sentido de o detetar. Assim, pretendeu-se com este projeto desenvolver metodologias com vista à deteção de muito baixas concentrações (entre o nano e o picoMolar) daquele composto em meio aquoso. Foi utilizada a tecnologia de Língua Eletrónica por Espectroscopia de Impedância e, para tentar melhorar a sensibilidade do sensor à molécula-alvo, foram utilizados filmes finos à base de nanotubos de carbono e de diferentes polieletrólitos, preparados pela técnica de Camada-sobre-Camada (LbL, do inglês Layer-by-Layer). A caracterização destes filmes foi feita pela técnica Espectrofotometria na faixa dos Ultravioleta e Visível. Para além da análise de diferentes concentrações de Ibuprofeno, foram ainda analisadas soluções de Cloreto de Sódio, com o intuito de perceber se o sensor é versátil na deteção de outro tipo de compostos, sendo, então, o sal um composto barato e relevante neste âmbito, uma vez que a água na Natureza apresenta sempre alguma salinidade. O trabalho compreendeu ainda o desenvolvimento de um programa informático para automatizar o processo de aquisição dos dados espectrais de impedância, recolhidos pelo analisador HAMEG Programmable LCR Bridge HM8118, o que foi feito com sucesso. Posteriormente, os dados foram tratados pelo procedimento estatístico de Análise de Componentes Principais, que permitiu discriminar espacialmente e sequencialmente as diferentes concentrações dos compostos analisados.

Cellulose-based composites as functional conductive materials for printed electronics

In this work, cellulose-based electro and ionic conductive composites were developed for application in cellulose based printed electronics. Electroconductive inks were successfully formulated for screen-printing using carbon fibers (CFs) and multi-walled carbon nanotubes (MWCNTs) as conductive functional material and cellulose derivatives working as binder. The formulated inks were used to fabricate conductive flexible and disposable electrodes on paper-based substrates. Interesting results were obtained after 10 printing passes and drying at RT of the ink with 10 % wt. of pristine CFs and 3% wt. of carboxymethyl cellulose (CMC), exhibiting a resistivity of 1.03 Ωcm and a resolution of 400 μm. Also, a resistivity of 0.57 Ωcm was obtained for only one printing pass using an ink based on 0.5 % wt. MWCNTs and 3 % wt. CMC. It was also demonstrated that ionic conductive cellulose matrix hydrogel can be used in electrolyte-gated transistors (EGTs). The electrolytes revealed a double layer capacitance of 12.10 μFcm-2 and ionic conductivity of 3.56x10-7 Scm-1. EGTs with a planar configuration, using sputtered GIZO as semiconducting layer, reached an ON/OFF ratio of 3.47x105, a VON of 0.2 V and a charge carrier mobility of 2.32 cm2V-1s-1.