Tomographic imaging with a scanning laser ophtalmoscop

Retinal imaging with a confocal scaning laser Ophthalmoscope (cSLO) involves scanning a small laser beam over the retina and constructing an image from the reflected light. By applying the confocal principle, tomographic images can be produced by measuring a sequence of slices at different depths. However, the thickness of such slices, when compared with the retinal thickness, is too large to give useful 3D retinal images, if no processing is done. In this work, a prototype cSLO was modified in terms hardware and software to give the ability of doing the tomographic measurements with the maximum theoretical axial resolution possible. A model eye was built to test the performance of the system. A novel algorithm has been developed which fits a double Gaussian curve to the axial intensity profiles generated from a stack of images slices. The underlying assumption is that the laser light has mainly been reflected by two structures in the retina, the internal limiting membrane and the retinal pigment epithelium. From the fitted curve topographic images and novel thickness images of the retina can be generated. Deconvolution algorithms have also been developed to improve the axial resolution of the system, using a theoretically predicted cSLO point spread function. The technique was evaluated using measurements made on a model eye, four normal eyes and seven eyes containing retinal pathology. The reproducibility, accuracy and physiological measurements obtained, were compared with available published data, and showed good agreement. The difference in the measurements when using a double rather than a single Gaussian model was also analysed.

Non-volatile analysis in fruits by laser resonant ionization spectrometry: application to resveratrol (3,5,4 -trihydroxystilbene) in grapes

Applied Physics B Lasers and Optics, vol.71

Laser welding of shape memory alloys

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Mecânica

Optimização da focagem de feixes laser em tecidos biológicos: desenvolvimento de um simulador óptico

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Biomédica

Estudo do efeito do tratamento por laser de objectos arqueológicos ferrosos

Dissertação de Mestrado em Conservação e Restauro - Metais

Correlation between the mechanical cycling behavior and microstructure in laser welded joints using NiTi memory shape alloys

Dissertação para obtenção do Grau de Mestre em Engenharia de Materiais

Forno solar com lentes de Fresnel e aplicações em laser solar

Dissertação para obtenção do Grau de Mestre em Engenharia Física

Optimização e construção de sistemas de laser solar

Dissertação para obtenção do Grau de Mestre em Engenharia Física

Laser solar de Nd: YAG bombeado por guias de onda

São propostas novas cavidades de bombeamento para lasers solares do estado sólido de Nd: YAG com o objectivo de melhorar a potência laser de saída e eficiência de bombeamento. São implementados quatro sistemas de guias de onda, um dos sistemas é simétrico e bombeado lateralmente, sendo os restantes três sistemas bombeados lateralmente e pela extremidade. A influência da geometria dos guias de onda no desempenho do bombeamento, o perfil do feixe à saída dos guias e a absorção por parte do cristal de Nd:YAG são optimizados minuciosamente, sendo modelados através do software Zemax. A cavidade de ressonância e as características do feixe são modelados em Lascad. Construíram-se e testaram-se três guias de onda de secção, octogonal, cilíndrica e quadrada. A potência laser multimodo para o sistema ótico bombeado por guia de onda cilíndrica de 20mm de diâmetro e concentrador cónico, foi de 21W, representando uma eficiência de colecção de 11.6W/m2, apresentando um erro de colecção para ΔX=1.3mm de 4.4%.

Predictive analytical and numerical modeling for orthogonal cutting

In this thesis, a predictive analytical and numerical modeling approach for the orthogonal cutting process is proposed to calculate temperature distributions and subsequently, forces and stress distributions. The models proposed include a constitutive model for the material being cut based on the work of Weber, a model for the shear plane based on Merchants model, a model describing the contribution of friction based on Zorev’s approach, a model for the effect of wear on the tool based on the work of Waldorf, and a thermal model based on the works of Komanduri and Hou, with a fraction heat partition for a non-uniform distribution of the heat in the interfaces, but extended to encompass a set of contributions to the global temperature rise of chip, tool and work piece. The models proposed in this work, try to avoid from experimental based values or expressions, and simplifying assumptions or suppositions, as much as possible. On a thermo-physical point of view, the results were affected not only by the mechanical or cutting parameters chosen, but also by their coupling effects, instead of the simplifying way of modeling which is to contemplate only the direct effect of the variation of a parameter. The implementation of these models was performed using the MATLAB environment. Since it was possible to find in the literature all the parameters for AISI 1045 and AISI O2, these materials were used to run the simulations in order to avoid arbitrary assumption.

Characterization of an OPCPA laser amplifier based on the nonlinear crystal YCOB

The work described in this thesis was performed at the Laboratory for Intense Lasers (L2I) of Instituto Superior Técnico, University of Lisbon (IST-UL). Its main contribution consists in the feasibility study of the broadband dispersive stages for an optical parametric chirped pulse amplifier based on the nonlinear crystal yttrium calcium oxi-borate (YCOB). In particular, the main goal of this work consisted in the characterization and implementation of the several optical devices involved in pulse expansion and compression of the amplified pulses to durations of the order of a few optical cycles (20 fs). This type of laser systems find application in fields such as medicine, telecommunications and machining, which require high energy, ultrashort (sub-100 fs) pulses. The main challenges consisted in the preliminary study of the performance of the broadband amplifier, which is essential for successfully handling pulses with bandwidths exceeding 100 nm when amplified from the μJ to 20 mJ per pulse. In general, the control, manipulation and characterization of optical phenomena on the scale of a few tens of fs and powers that can reach the PW level are extremely difficult and challenging due to the complexity of the phenomena of radiation-matter interaction and their nonlinearities, observed at this time scale and power level. For this purpose the main dispersive components were characterized in detail, specifically addressing the demonstration of pulse expansion and compression. The tested bandwidths are narrower than the final ones, in order to confirm the parameters of these elements and predict the performance for the broadband pulses. The work performed led to additional tasks such as a detailed characterization of laser oscillator seeding the laser chain and the detection and cancelling of additional sources of dispersion.

Recuperação renovável de Mg a partir de MgO através da utilização concertada de laser solar e de concentrador solar

Apesar do elevado potencial do metal magnésio como material útil em várias áreas cien-tíficas e tecnológicas, os seus métodos de produção tradicionais têm um impacto fortemente prejudicial no ambiente e um custo elevado. Este facto é um incentivo à procura de novas so-luções, nomeadamente as que recorrem à utilização da radiação solar partindo do óxido de magnésio. Alguns estudos têm já sido feitos nesse sentido, utilizando laser solar ou radiação solar concentrada mas a utilização concertada dos dois não tinha sido feita até ao momento. Neste trabalho, a exequibilidade da utilização concertada destes dois métodos será avaliada e será estudado o comportamento do óxido de magnésio face à radiação que nele incide.

Melhoramento e automatização de um sistema de revestimento com laser

O revestimento com laser permite criar revestimentos localizados pela adição de uma liga similar ou dissimilar. O revestimento visa melhorar as características da superfície metálica, tais como a dureza, a resistência ao desgaste por atrito, à corrosão e à fadiga térmica dos componentes sujeitos a condições adversas de trabalho por prolongados períodos de tempo. Esta dissertação tem como objetivo o melhoramento da configuração, a automatização do sistema de revestimento com laser do Laboratório de Laser do Instituto Superior Técnico (IST) da Universidade de Lisboa, utilizado pelo Centro de Física e Engenharia de Materiais Avançados do Instituto Superior Técnico – CeFEMA e a realização de ensaios de deposições com o fim de validação. Foram estudadas as configurações possíveis para o sistema de posicionamento da amostra, do laser e a configuração para o posicionamento com precisão do bocal de adição de pós ao banho de fusão. Após este estudo foram apresentadas e implementadas as propostas de melhoria do sistema inicial. Para tornar o sistema funcional, foi desenvolvido um controlador para comandar as três guias motorizadas de movimento linear OWIS, o laser IPG YLR e o alimentador de pós PLASMA-TECHNIK. Para simplificar a utilização aos investigadores do CeFEMA foi ainda desenvolvida uma interface gráfica que permite ao utilizador definir os principais parâmetros do processo Para a validação do trabalho desenvolvido foram realizados diversos ensaios de deposição da liga Ti52Ta num substrato de titânio. Através dos ensaios de deposição foi estudada a influência de alguns parâmetros do processo na geometria do revestimento obtido, como a altura, a profundidade, o ângulo do cordão, a diluição entre o material de adição e o substrato, tendo ainda sido estudada a influência dos parâmetros do processo na eficiência de deposição.

Development of an experimental setup for metal cutting research

Analytical, numerical and experimental models have been developed over time to try to characterize and understand the metal cutting process by chip removal. A true knowledge of the cutting process by chip removal is required by the increasing production, by the quality requirements of the product and by the reduced production time, in the industries in which it is employed. In this thesis an experimental setup is developed to evaluate the forces and the temperature distribution in the tool according to the orthogonal cutting model conditions, in order to evaluate its performance and its possible adoption in future works. The experimental setup is developed in a CNC lathe and uses an orthogonal cutting configuration, in which thin discs fixed onto a mandrel are cut by the cutting insert. In this experimental setup, the forces are measured by a piezoelectric dynamometer while temperatures are measured by thermocouples placed juxtaposed to the side face of the cutting insert. Three different solutions are implemented and evaluated for the thermocouples attachment in the cutting insert: thermocouples embedded in thermal paste, thermocouples embedded in copper plate and thermocouples brazed in the cutting insert. From the tests performed in the experimental setup it is concluded that the adopted forces measurement technique shows a good performance. Regarding to the adopted temperatures measurement techniques, only the thermocouples brazed in the cutting insert solution shows a good performance for temperature measurement. The remaining solutions show contact problems between the thermocouple and the side face of the cutting insert, especially when the vibration phenomenon intensifies during the cut. It is concluded that the experimental setup does not present a sufficiently robust and reliable performance, and that it can only be used in future work after making improvements in the assembly of the thermocouples.

Building 3D City Models: Testing and Comparing Laser Scanning and Low-Cost UAV Data Using FOSS Technologies

Contém resumo