Study of AC losses in medium-sized high temperature superconducting coils

The study of AC losses in superconducting pancake coils is of utmost importance for the development of superconducting devices. Due to different technical difficulties this study is usually performed considering one of two approaches: considering superconducting coils of few turns and studying AC losses in a large frequency range vs. superconducting coils with a large number of turns but measuring AC losses only in low frequencies. In this work, a study of AC losses in 128 turn superconducting coils is performed, considering frequencies ranging from 50 Hz till 1152 Hz and currents ranging from zero till the critical current of the coils. Moreover, the study of AC losses considering two different simultaneous harmonic components is also performed and results are compared to the behaviour presented by the coils when operating in a single frequency regime. Different electrical methods are used to verify the total amount of AC losses in the coil and a simple calorimetric method is presented, in order to measure AC losses in a multi-harmonic context. Different analytical and numerical methods are implemented and/or used, to design the superconducting coils and to compute the total amount of AC losses in the superconducting system and a comparison is performed to verify the advantages and drawbacks of each method.

Bio-inspired anatomy for autonomous DPWS-compliant automation components

Dissertação apresentada na Faculdade de Ciências e Engenharia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

A qualitative assessment of modularity in CaesarJ components based on implementations of design patterns

Tese de Mestrado em Engenharia Informática

Petri nets based components within globally asynchronous locally synchronous systems

Dissertação apresentada na Faculdade de Ciências e Tecnologias da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e Computadores

Quantitative assessment of modularity of caesarJ components

Dissertação apresentada no âmbito do Mestrado em Engenharia Informática para obtenção do grau de Mestre em Engenharia Informática

RepComp - replicated software components for improved performance

Trabalho apresentado no âmbito do Mestrado em Engenharia Informática, como requisito parcial para obtenção do grau de Mestre em Engenharia Informática

Pozzolanic components in lime mortars: correlating behaviour, composition and microstructure.

Int. J. for Restoration of Buildings and Monuments, vol.11, nº 2 (2005), p.111-118

Lean production in the precast concrete components’ industry

Proceedings IGLC-19, July 2011, Lima, Perú

Distributed replicated macro-components

Dissertação para obtenção do Grau de Mestre em Engenharia Informática

The effect of hydraulic components on lime mortars

XXX IAHS World Congress on Housing - Housing Construction: An Interdisciplinary Task, September 9-13, 2002, Coimbra, Portugal

Adsorption equilibria of flue gas components on activated carbon

Dissertação para obtenção do Grau de Mestre em Engenharia Química e Bioquímica

Lime mortars with ceramic wastes: characterization of components and their influence on the mechanical behaviour

Considering the fundamental importance of preserving the built heritage and of ensuring the good performance achieved by incorporating ceramic particles in lime mortars in ancient times, it is important to study solutions that use materials the available today, in order to produce mortars intended to repair and replace the old ones. Solutions incorporating industrial ceramic waste might be profitable for several reasons, namely for economic, environmental and technical aspects. In this paper, seven ceramic waste products collected from ceramics factories are characterized. Their mineralogy, dimensional features and pozzolanicity were determined. Three of these products, with different particle size fractions (obtained directly from milling, dust only and fragment fractions only), were selected, incorporated into air lime mortars, and their mechanical strength was determined. In the present work, evidence of mechanical efficiency, when common sand or air lime were partially replaced by ceramic wastes, was made clear, drawing attention to the sustainability of this type of mortars, hence, encouraging further research.

Fishing the key biological components of the bacterium Geobacter metallireducens for optimal biotechnological applications

Os resultados apresentados no capítulo 2 foram incluídos no artigo Dantas JM, Campelo LM, Duke NEC, Salgueiro CA, Pokkuluri PR (2015) "The structure of PccH from Geobacter sulfurreducens – a novel low reduction potential monoheme cytochrome essential for accepting electrons from an electrode", FEBS Journal, 282, 2215-2231.

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications.